Columbia Bearing Parts

This is a bushing made from black plastic with a cleft down the middle to provide enough flex for easy insertion. It has a flanged design, which means it won’t easily pop out after installation, even under stress from constant vibration. The bushing’s primary purpose is to protect wires and cables from damage as they pass through a channel. As such, the material is fairly durable and does not need to be replaced under ordinary circumstances. That said, there are some situations in which it can become damaged. For one thing, it’s easy to damage while repairing the wires or cables that run through the bushing. If the bushing does need to be replaced, it requires disconnecting any cables or wires that run through the bushing. Pop out the old bushing with a rubber mallet, install the new bushing the same way, reconnect the wires, and the repair is complete. This is an OEM part sourced directly from MTD, and it is sold individually. It was initially used on snowblowers but has also been used on lawnmowers and lawn tractors.

This is an authentic OEM replacement flange bearing sourced directly from the manufacturer that is a component in many different lawn and garden machines. The flange bearing is used to tightly fit between two connected components. This connection creates an airtight seal. Over time and with normal wear and tear, the flange can become worn and lose the seal. When this happens, the flange will need to be replaced. The flange helps to distribute the weight load in some instances and if it is damaged, the weight would be displaced and could lead to serious energy.Replacement depends on the location of the flange that needs to be replaced. Place the equipment on a flat surface and disconnect the spark plug wire. Take the machine's components off as needed to access the flange and remove it using a pair of pliers. Clean off the components where the bearing was located before installing the new flange bearing. Reassemble the machine using a reverse process.This flange is a heavy-duty part that is sold as an individual item. The flange bearing can be used with lawnmowers and other lawn and garden machines manufactured by Craftsman.

A ball bearing is a common type of rolling-element bearing. It will use balls to keep space between the bearing races and eliminate friction and contact between moving parts. Ball bearings used in lawn and garden equipment ensure that axial loads and radial loads are evenly supported and that there is only a limited amount of rotational friction on the component. It distributes weight evenly, but will undergo constant wear and tear from vibration, heat, and friction and will need replacement regularly. This ball bearing is a genuine OEM part suited to use in Craftsman, Cub Cadet, Ryobi, Troy-Bilt, MTD, Huskee, Yard Machines, Bolens, Mastercut, and Yard-Man equipment. It may be needed for repair work done on a lawnmower, snowblower, tiller, edger, or a log splitter.

This is a pawl that can serve as a replacement for some mower models, as well as chippers and shredders. The pawl attaches to the ratchet pawl plate. The pawl is essential for starting the engine. When the starter turns, the pawl is forced outward and locks onto the flywheel, allowing the engine to start. When the starter rope is let go, the springs pull back the ratchet pawls. If there is damage to the pawl, the engine will not start.The piece is made from durable metal, and it is built to last. However, it can start to wear down over time. Additionally, there is the potential that it could corrode. If there are issues with the pawl, replace them as soon as possible to ensure their machine continues to operate properly.This pawl can work with select models from MTD, Troy-Bilt, Yard-Man, Cub Cadet, and Husky. The piece is a genuine OEM replacement part sourced from the manufacturer. It is sold individually.

This part is a replacement hex flange bearing. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a detached, defective, or damaged hex flange bearing in a variety of lawn tractor models. This part provides support for the lawn tractor shaft and also enables it to rotate without creating too much friction. This is a high wear and tear part and may require replacement with age or regular equipment use. A wrench set and screwdriver will be needed to replace this part. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. For more accurate information on how and where to install this hex flange bearing, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this hex flange bearing is suitable for use on several different models of lawn tractors manufactured by MTD, Troy-Bilt, Yard Man, and Cub Cadet. This is a genuine part made of high-quality, durable metal and is sold individually.