Parts for Kenmore 417.99980140 (41799980140, 417 99980140): Console & Controls Parts

The washer agitator stud cap is a small cover piece that fits on top of the central agitator post in top-loading washing machines. Replace this cap if it's cracked, missing, loose, or if fabric is getting caught on the exposed agitator mechanism.

The dryer timer power resistor regulates electrical current to the timer motor in mechanical timer systems. Replace when the timer fails to advance properly, gets stuck in cycles, or the dryer runs continuously without stopping.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

PPH ab st/z/ch `6 - 18x.60

This part has been discontinued by the manufacturer and is no longer available.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

A replacement mounting screw used to secure components on compatible Frigidaire appliances. This genuine-style fastener restores proper fit where the original screw is missing, stripped, or damaged for safe operation. What it does:

• Secures trim, panels, brackets, or components to prevent rattling and misalignment
• Restores a proper mechanical connection when the original screw is lost or worn
• Helps eliminate vibration noise caused by loose fasteners
• Compatible with specific Frigidaire assemblies that use this style of screw

• Screw only

• Use the correct screw location and size—do not force or overtighten to avoid stripping threads or cracking plastic parts
• Turn off power or disconnect appliance from power source before accessing internal components
• Wear safety glasses and handle small parts carefully to avoid injury or loss

Secures wiring harness to prevent chafing and maintain safe wire routing in washers, dryers, and laundry appliances. Replace if loose or broken. Check your model for compatibility.

This part has been discontinued by the manufacturer and is no longer available.

PPH ab st/z/ch `6 - 18x.60

Red adhesive strip for washers. Secures components and panels inside the cabinet. Replace if peeling, missing, or no longer holding parts in place.

This part has been discontinued by the manufacturer and is no longer available.

Snap-in bushing for washer assemblies. Replaces worn, cracked, or missing bushings that provide cushioning and support in internal components.

This component adjusts the tension of washer suspension springs in laundry center units and is located within the suspension system. Replace when experiencing excessive vibration, unbalanced loads, or unusual movement during spin cycles.

This door gasket creates a tight seal around the refrigerator door to help maintain proper cooling and reduce energy loss. Replacing a worn gasket restores a full seal for better temperature control and food preservation. What it does:

• Seals the door to prevent warm, humid air from entering the refrigerated compartment
• Helps reduce frost buildup and keeps interior temperatures stable
• Improves cooling efficiency and can lower energy use caused by a leaking seal
• Stops odors and moisture transfer between the fridge interior and kitchen

• Unplug the refrigerator before starting and remove any food or shelves blocking the seal.
• Work slowly to avoid stretching or creasing the gasket; follow door-hinge or trim removal steps if needed.
• Inspect the door flange for damage and clean the mating surface before installing the new gasket.
• After installation, allow the gasket to seat fully and check for uniform contact around the door; warm-up or seating time may be needed.

Replace the control panel housing cover on your washer or washer dryer combo. Needed when the original housing is cracked, broken, or damaged.

Agitator rod and gear kit for washers. Connects the agitator to the drive system. Replace if gears are stripped, worn, or rod is broken or damaged.

Washer door seal o-ring prevents leaks and maintains proper door closure. Replace if cracked, worn, or leaking. Confirm fit with your model number.

Suspension spring for washer drum support system. Replaces worn, stretched, or broken springs that no longer properly suspend the tub assembly.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

This replacement door gasket seals the refrigerator/freezer door to help maintain consistent temperatures and reduce frost buildup. It restores the cabinet seal so the appliance can cool efficiently and run less often. What it does:

• Provides an airtight seal around the door to keep cold air in and warm air out
• Helps reduce frost buildup and freezer run time caused by leaks
• Can stop common symptoms like warm spots inside the compartment, excessive frost, or frequent compressor cycling
• Fits into the door channel and compresses to form a continuous seal when the door is closed

• Disconnect power to the appliance before starting any repairs
• Remove the old gasket and thoroughly clean the door channel before installing the new gasket
• Press the gasket evenly into the channel, working around the door to ensure a continuous, wrinkle-free seal
• Avoid using sharp tools that could damage the new gasket; allow the gasket to fully seat before checking for leaks

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.

The Agitator Hub is an OEM part for Frigidaire washing machines. It connects the agitator to the drive shaft, enabling the agitator to rotate and move clothes effectively during the wash cycle.  

Causes of a bad agitator hub can include wear and tear from frequent use, exposure to harsh detergents or hard water, or damage from overloading the washer.  

Symptoms of a bad agitator hub include:

• Agitator not moving or rotating properly
• Loud noises or grinding sounds during the wash cycle
• Clothes not being cleaned effectively
• The washer shaking or vibrating excessively

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Tub Seal is an OEM part for Frigidaire washing machines. It is designed to create a water-tight seal between the washing machine tub and the transmission or drive system. This seal prevents water from leaking out during the operation of the washer and protects the mechanical components from water damage.

Symptoms of a failing tub seal include:

• Water leaking from the underside of the washing machine.
• Increased moisture or puddles forming under the machine during use.
• A musty or moldy smell, indicating that water has been seeping and not properly drying.

Causes of a bad tub seal can include aging and wear over time, exposure to harsh detergents that degrade the material of the seal, or mechanical stress from unbalanced loads that can cause the seal to fail. It's important to address these issues promptly to prevent further damage to the washing machine.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.