Parts for Kenmore 110.25132410 (11025132410, 110 25132410): Console And Water Inlet Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This control panel is the appliance's user interface that lets you select cycles and settings and shows status information. Replace a damaged or unresponsive panel to restore reliable control and clear display feedback. What it does:

• Provides the touchpad/buttons and display area for selecting cycles and options
• Sends user commands to the appliance's main control board for execution
• Common symptom: buttons or touchpad don't respond or commands aren't registered
• Common symptom: display is blank, unreadable, or shows incorrect status

• Disconnect power to the appliance before beginning any service to avoid shock
• Handle the panel carefully to avoid damaging the display, ribbon cables, or mounting tabs
• Some installations require removing the outer console or trim—keep fasteners and note their locations
• Ensure connectors are fully seated before testing power

The Knob Spring Clip is an OEM part for Whirlpool appliances, specifically designed for use in washers and dryers. This small but essential component is responsible for securing the control knob to the control panel, ensuring that the knob stays firmly in place during operation.

Common causes of a bad spring clip include frequent use, accidental impacts, or wear and tear over time. A faulty spring clip can result in the control knob becoming loose or falling off, making it difficult to operate the appliance.

Symptoms of a bad knob spring clip include:

• The control knob is loose or wobbly
• The control knob falls off easily
• Difficulty in turning or setting the control knob
• The appliance not responding correctly to knob adjustments

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This electronic control board is the main control module that manages your appliance's user interface and timed functions, restoring normal operation when the original control becomes unresponsive or erratic. What it does:

• Replaces the appliance's failed/main control module that runs cycles, timing, and electronic commands
• Restores control of display, touchpad/knobs, and programmed cycles when the original board malfunctions
• Commonly used when the unit shows unresponsive controls, error codes, or intermittent operation related to the control board
• Works with the appliance's existing wiring harness and user interface

• One electronic control board

• Disconnect power to the appliance before attempting replacement to avoid shock or injury
• Handle the board by its edges and avoid touching components or connector pins to prevent static damage
• Verify connector locations and orientation before unplugging; take photos if needed to ensure correct reassembly

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This cycle switch is the user-controlled selector that tells the washer which wash sequence to run, restoring normal cycle selection and operation. It provides a direct replacement for a worn or non-responsive cycle selector. What it does:

• Selects and routes electrical signals to start the chosen washer cycle
• Restores reliable selection when the dial won't change cycles or the machine won't advance
• Helps resolve intermittent or no-response issues from the cycle selector control
• Works as the mechanical/electrical interface between the user dial and the washer's control system

• (1) cycle switch (selector)

• Turn off and unplug the appliance before attempting any service
• Access may require removing the control console or rear panel; handle wires and connectors gently
• Only install parts that match the appliance's original part number

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This heavy-duty replacement power cord restores the appliance's connection to household power, delivering reliable electrical continuity for normal operation. Ideal when the original cord is damaged, burned, or fails to supply power. What it does:

• Carries mains electricity from the wall outlet to the appliance so controls and heating elements can operate
• Replaces frayed, cracked, melted, or otherwise damaged cords that may cause intermittent power or no power
• Helps eliminate sparking, overheating, or visible insulation damage at the cord or plug
• Matches the OEM fit and wiring configuration for a direct replacement when compatible

• One power cord

• Disconnect power at the breaker or unplug the appliance before beginning any work
• Verify wiring color and connector orientation match the appliance before attaching
• Secure strain relief and routing to prevent pinching or chafing; tighten terminal connections firmly

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The timer knob assembly lets you turn and set the appliance's mechanical timer. When the original knob is cracked, stripped, or missing, this replacement restores a secure grip so cycles or time settings can be selected reliably.

• Attaches to the timer shaft to select cycles or time settings
• Restores positive engagement when the original knob is worn or broken
• Common fix for a knob that spins freely, slips, or falls off
• Helps resolve difficulty setting or starting a cycle caused by a damaged knob

• Disconnect power to the appliance before replacing the knob
• Pull the old knob straight off the timer shaft; if tight, gently wiggle while pulling
• Align the new knob with the shaft and press firmly until fully seated
• Verify smooth operation through the full range of timer positions

This genuine Whirlpool control knob provides a reliable replacement for a worn, cracked, or missing appliance control. It restores a solid grip and smooth control operation so you can set cycles and temperatures with confidence. What it does:

• Replaces a broken, loose, or missing control knob so the control shaft can be turned securely
• Restores tactile grip and clear pointer alignment for accurate settings
• Stops slipping or spinning that prevents proper selection of cycles or temperatures
• Compatible with original control shafts that use a push-on or screw-retained knob design

• One control knob

• Disconnect power to the appliance before servicing to avoid injury
• Remove the old knob by pulling straight off the control shaft; retain any small screw or retaining clip if present
• Align the replacement knob with the splines on the control shaft and push into place; secure with the original screw or clip if required

This cycle switch controls and redirects power to the washer's/dryer's timer or motor circuits so the appliance advances through its programmed cycles. It restores proper cycle selection and progression when the knob does not change settings. What it does:

• Routes electrical signals to the correct cycle/timer contacts so selected programs run.
• Commonly replaced when cycles won't advance, the selector won't engage, or the control knob feels loose or unresponsive.
• Helps resolve intermittent operation or failure to start specific wash/dry functions tied to cycle position.
• Matches OEM function for reliable replacement of the selector switching stage.

• Disconnect power before servicing to avoid shock—electrical expertise recommended.
• Verify knob/timer compatibility and orientation before final assembly.
• Handle gently and avoid bending terminals; test function before reassembling the cabinet.

The Water Inlet Valve is an OEM part for Whirlpool washing machines. This valve controls the flow of water into the washer, allowing it to fill with the correct amount of water during the wash and rinse cycles.

Over time, the water inlet valve can become clogged with debris, develop electrical issues, or wear out, leading to problems with the water flow. Causes of a bad water inlet valve include mineral buildup from hard water, internal component failure, or damage to the valve body.

Symptoms of a bad water inlet valve include:

• The washing machine not filling with water
• Slow or insufficient water flow into the washer
• The washer filling with water when it should not
• Unusual noises during the filling process
• Leaks around the valve area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This main wire harness routes power and signals between the appliance control and internal components to restore proper electrical connections and operation. It's a direct-fit replacement when the original harness is damaged. What it does:

• Connects control board, motors, switches and sensors so circuits receive power and communicate correctly
• Replaces frayed, broken, or corroded wiring that can cause intermittent operation or component failure
• Helps stop issues like no power to controls, intermittent runs, or unexpected shutdowns when caused by damaged wiring
• Maintains factory routing and connector types for reliable electrical connections

• One main wire harness

• Disconnect power (unplug or shut off breaker) before inspecting or replacing the harness
• Compare harness and connectors to the original and route wires following factory paths to prevent chafing
• Secure connectors fully until they click; avoid stretching wires when reinstalling

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.