Parts for Whirlpool GX900QPPB2: 04 - Container Parts

This replacement screw secures panels, brackets, and internal components inside your appliance to keep them aligned and rattle-free. Replace stripped, rusty, or missing hardware to restore a tight fit and dependable operation.

• Holds metal panels, brackets, ducts, or trim in place
• Helps maintain alignment and reduces vibration and noise
• Replaces missing, corroded, or stripped screws
• Common symptoms: loose panel or component, rattling/buzzing during use, screw won't tighten

• Disconnect power and shut off gas/water before servicing
• Start threads by hand to avoid cross-threading; use the correct driver
• Replace one fastener at a time to maintain alignment
• Tighten snugly—do not overtighten to prevent stripping

Replacement door handle for your compactor. Installs on the door to restore a secure grip. Needed when the original is cracked, broken, or loose.

This is a white plastic drawer handle for a trash compactor, mounted on the front of the compactor drawer to allow you to open and close it. It attaches with screws or snap-in fasteners to the drawer panel. Replace this handle if it is cracked, broken, or missing, making it difficult to pull the compactor drawer open.

This is a black handle that attaches to the front of the trash compactor drawer, allowing you to pull the drawer open and push it closed. It mounts with screws through the drawer panel. Replace this handle if it is cracked, broken, or loose, making it difficult to operate the compactor drawer.

Biscuit-colored front panel for trash compactor container. Replace this decorative trim piece if cracked, discolored, or damaged to restore appearance.

White front container panel for trash compactors. Replaces scratched, chipped, or discolored panels on the compactor container exterior. Restores appearance.

This is the front-facing outer door panel for a trash compactor, featuring a stainless steel finish. It serves as the visible exterior surface of the compactor drawer, providing a clean and finished appearance. Replace this panel if it is dented, scratched, rusted, or otherwise cosmetically damaged.

Size: 8-18 x 1/2 inch.

This latch assembly secures the trash compactor drawer in the closed position and engages the safety interlock that allows the compactor to operate. It mounts to the front of the compactor frame and connects to the door switch mechanism. Replace this part if the drawer will not latch shut, the compactor fails to start because it does not detect a closed door, or the latch mechanism is visibly broken or worn.

Replacement foot pedal for trash compactors. Operates the compacting mechanism when pressed. Replace if cracked, broken, or missing for proper operation.

White plastic foot pedal for trash compactors. Installs at base of unit to release door latch. Replace if cracked, broken, or no longer springs back.

Replacement foot pedal for trash compactors. Installs at the base to operate the door release mechanism. Replace if cracked, broken, or missing.

Compactor won't run unless you hold the dial? A worn safety switch actuator prevents proper door latch engagement. This repair restores automatic operation.

Replacement roller bearing for trash compactor drawers. Installs on tracks to support smooth gliding. Replace worn or damaged bearings for easier operation.

This threaded fastener secures components within your trash compactor, ensuring proper alignment and operation of moving parts. It provides a strong mechanical connection that withstands the forces generated during compaction cycles. Replace if components become loose or if the original nut is damaged or missing.

Fits 15 and 18 inch compactors. This kit is for securing the compactor bags. Kit contains a set of 4 buttons and screws.

Size: 8-32 x 3/8 inch.

This latch pin secures the door latch mechanism on your trash compactor. Replace if the pin is broken, worn, or missing to restore proper door latching.

Latch spring for trash compactors. Installs in the door latch mechanism to provide tension. Replace if cracked, broken, or missing to restore proper latch function.

Compactor door won't latch or latch feels loose? This E-ring retaining clip secures latch components to the shaft. Quick 5-minute fix for latch problems.

Replace worn, stripped, or missing 8-18 x 3/8 machine screws that secure control panels, trim pieces, and brackets on your appliance. Restores tight fit.

Door strike plate for trash compactors. Mounts to cabinet frame to secure the door latch. Replace if cracked, bent, or missing to restore proper closure.

Protective guard for trash compactors. Shields internal components from debris and impact. Replace if cracked, broken, or missing to maintain proper function.

Front guard plate for trash compactors. Protects the compactor front panel from damage. Replace if cracked, torn, or worn to restore appearance.

Replacement fastener screw for appliances. Secures panels, trim, clips, and components. Needed when original screws are stripped, missing, or damaged.