Parts for Kitchenaid KUCK03ITBL0: 04 - Container Parts

This replacement screw secures panels, brackets, and internal components inside your appliance to keep them aligned and rattle-free. Replace stripped, rusty, or missing hardware to restore a tight fit and dependable operation.

• Holds metal panels, brackets, ducts, or trim in place
• Helps maintain alignment and reduces vibration and noise
• Replaces missing, corroded, or stripped screws
• Common symptoms: loose panel or component, rattling/buzzing during use, screw won't tighten

• Disconnect power and shut off gas/water before servicing
• Start threads by hand to avoid cross-threading; use the correct driver
• Replace one fastener at a time to maintain alignment
• Tighten snugly—do not overtighten to prevent stripping

Replacement handle for trash compactor containers. Installs on the front of the compactor bin for easy pull-out access. Order if your handle is cracked or broken.

Replacement drawer container for trash compactors. Installs as the main compartment to hold contents securely. Needed when original is cracked, broken, or deformed.

Fix a stuck or difficult-to-open compactor drawer with this replacement foot pedal. Restores hands-free drawer release and smooth latch operation.

Size: 8-32 x 3/8 inch.

This door lock latch assembly secures the washer door during operation so cycles can run safely and water stays contained. It replaces a worn or damaged latch to restore proper door locking and cycle start. What it does

• Secures and locks the washer door during wash and spin cycles so the appliance can operate normally.
• Triggers the door-closed sensor/switch that allows the washer to start and continue a cycle.
• Helps prevent accidental door opening and reduces the risk of leaks during operation.
• Common symptoms indicating this part may be needed: washer won't start, door won't latch or lock, or the latch feels loose or broken.

• Always disconnect power to the appliance before inspecting or replacing the door lock latch.
• Handle the door and glass carefully to avoid damage; align the latch with the strike before tightening fasteners.
• After installation, test a short cycle (no clothes) to ensure the door locks and the washer starts properly.

Compactor won't run unless you hold the dial? A worn safety switch actuator prevents proper door latch engagement. This repair restores automatic operation.

Color: White. For black use W10021860. For stainless use W10021850.

This identification nameplate displays your dishwasher's model information and operating instructions for easy reference. It typically mounts on the door frame or control panel area and includes important safety and usage details. Replace this nameplate if it's become illegible, damaged, or has come loose from its mounting location.

Size: 8-18 x 1/2 inch.

Replacement fastener screw for appliances. Secures panels, trim, clips, and components. Needed when original screws are stripped, missing, or damaged.

Replacement roller bearing for trash compactor drawers. Installs on tracks to support smooth gliding. Replace worn or damaged bearings for easier operation.

This threaded fastener secures components within your trash compactor, ensuring proper alignment and operation of moving parts. It provides a strong mechanical connection that withstands the forces generated during compaction cycles. Replace if components become loose or if the original nut is damaged or missing.

Front guard plate for trash compactors. Protects the compactor front panel from damage. Replace if cracked, torn, or worn to restore appearance.

This latch pin secures the door latch mechanism on your trash compactor. Replace if the pin is broken, worn, or missing to restore proper door latching.

Latch spring for trash compactors. Installs in the door latch mechanism to provide tension. Replace if cracked, broken, or missing to restore proper latch function.

Compactor door won't latch or latch feels loose? This E-ring retaining clip secures latch components to the shaft. Quick 5-minute fix for latch problems.

Door strike plate for trash compactors. Mounts to cabinet frame to secure the door latch. Replace if cracked, bent, or missing to restore proper closure.

Fits 15 and 18 inch compactors. This kit is for securing the compactor bags. Kit contains a set of 4 buttons and screws.