Parts for Kitchenaid KTTS505ESS2: Container Parts

This is a replacement machine screw sized 8-18 x 3/8 that secures panels and components on compatible appliances. It restores proper fastening where a worn, stripped, or missing screw causes loose parts or rattling. What it does

• Fastens control panels, trim pieces, or brackets to the appliance chassis
• Replaces stripped, corroded, or missing screws that cause loose panels or vibrating noise
• Provides correct thread engagement for a secure hold in tapped holes
• Small hardware solution often used during door, console, or interior repairs

• One 8-18 x 3/8 machine screw (quantity: 1)

• Use the correct screw size and thread; do not force a different-size fastener into tapped holes
• Hand-start the screw to avoid cross-threading, then tighten with the appropriate screwdriver
• Disconnect power before accessing internal components or panels on electrical appliances
• If metal threads are damaged, repair with a helicoil or replace the damaged component rather than over-torquing

This actuator is the small mechanism that drives the dishwasher's detergent dispenser door, releasing detergent at the correct time in the cycle for consistent cleaning performance. What it does:

• Converts a control signal into movement to open the dispenser door
• Helps ensure detergent is released at the proper stage of the wash
• Wear or breakage can leave the cup closed or only partially opened
• Common symptoms: detergent left in cup after cycle, dispenser door not opening, or visible damage to the lever

• 1 actuator

• Disconnect power at the breaker before servicing
• Open the door and remove the inner door panel to access the dispenser assembly
• Note the actuator's orientation; transfer and seat it fully in the mechanism
• Reassemble the door, restore power, and run a short cycle to confirm proper dispenser operation

This part is the outer panel for the drawer on a trash compactor. This part protects the wiring and other components inside of the drawer and also provides a decorative finish for the face of the unit.In the event that the stainless steel finish becomes scratched, dented, or damaged in any way, this is a high-quality replacement part. The screws may need to be reused when installing the new part, so keep those in a safe place so they do not get lost. Before replacing this part, unplug the unit from the electrical outlet or turn off the house circuit breaker. Wears gloves for safety during this process.This outer panel is compatible with trash compactors that are manufactured by the Whirlpool and KitchenAid brands. It is sold individually and sourced straight from the manufacturer as a genuine OEM part.

This replacement container restores a secure, factory-fit compartment in your appliance. Install a new container when the original is cracked or broken to keep contents properly held and nearby parts aligned as designed.

• Provides the designated compartment to hold contents securely
• Interfaces correctly with its mounting points, guides, or adjoining parts
• Replaces cracked, warped, or broken containers that won't stay seated
• Helps prevent spills, jams, or interference with nearby components

• Disconnect power to the appliance; shut off water supply if applicable
• Wear cut-resistant gloves—damaged plastic edges can be sharp
• Move any screws, covers, or inserts from the old part to the new one
• Align tabs, tracks, or snaps and press into place without forcing

This name plate is the appliance's model and serial identification label—an easy way to restore clear product ID for service, parts ordering, and warranty records. Keeps your appliance information visible and readable. What it does:

• Displays manufacturer model and serial numbers and other factory ID details
• Restores a missing or damaged ID label so technicians can identify the correct parts and specs
• Helps when registering the appliance or filing warranty and service requests
• Prevents delays caused by unreadable or absent identification information

• Clean and dry the mounting surface before applying; remove old adhesive residue
• Align carefully and press firmly; some name plates use adhesive backing or mounting tabs
• Do not cover vents, controls, or safety labels when installing

This replacement foot pedal mounts at the base of the trash compactor to provide hands-free drawer release. Replace a worn, cracked, or missing pedal to restore easy opening, proper latch engagement, and smooth operation. What it does:

• Engages the drawer release mechanism when stepped on
• Enables hands-free access when your hands are full
• Helps ensure the drawer opens and latches correctly
• Helps with symptoms such as a broken/missing pedal, difficulty opening the drawer, or a pedal that feels loose or does not return

• One foot pedal

• Disconnect power to the compactor and empty the drawer before servicing
• Remove the toe panel or mounting screws to access the pedal attachment points
• Reuse existing mounting hardware from the original pedal, aligning the new pedal correctly
• Verify smooth pedal action and proper drawer release before restoring power

This door lock latch assembly secures the washer door during operation so cycles can run safely and water stays contained. It replaces a worn or damaged latch to restore proper door locking and cycle start. What it does

• Secures and locks the washer door during wash and spin cycles so the appliance can operate normally.
• Triggers the door-closed sensor/switch that allows the washer to start and continue a cycle.
• Helps prevent accidental door opening and reduces the risk of leaks during operation.
• Common symptoms indicating this part may be needed: washer won't start, door won't latch or lock, or the latch feels loose or broken.

• Always disconnect power to the appliance before inspecting or replacing the door lock latch.
• Handle the door and glass carefully to avoid damage; align the latch with the strike before tightening fasteners.
• After installation, test a short cycle (no clothes) to ensure the door locks and the washer starts properly.

This handle spacer positions and secures a dishwasher or appliance door handle, keeping the handle aligned and preventing rubbing or binding for smooth door operation. It's a small replacement piece that restores proper handle fit. What it does:

• Provides a stable mounting gap between the handle and door/frame to ensure correct alignment
• Prevents handle contact with the door surface that can cause wear or noise
• Restores proper spacing after a broken, worn, or missing spacer
• Suitable when the handle feels loose, sits crooked, or rubs against the door

• One handle spacer

• Install with the appliance door open on a stable surface; follow the appliance manufacturer's fastening sequence
• Use hand tools only unless the OEM instructs otherwise; avoid overtightening fasteners
• Disconnect power or follow manufacturer safety instructions when required for handle removal

This safety switch actuator engages the door/interlock switch so the appliance senses a closed, secure door and will run as intended. Replacing a worn actuator restores reliable door engagement and control-system signaling. What it does:

• Moves the door latch into position to trip the appliance's safety/interlock switch
• Ensures the control board senses a closed door so cycles can start or continue
• Common symptom: appliance won't start or stops when the door is shut or nudged
• Common symptom: door won't fully latch or feels loose when closing

• One safety switch actuator

• Disconnect power (and water if applicable) before starting any repair
• Remove exterior panels or door assembly as needed to access the actuator; keep fasteners organized
• Verify switch alignment with the actuator and test operation before reassembly
• Wear gloves and eye protection

This small mounting screw secures panels and components in place so parts stay aligned and appliances run quietly and safely. It's a direct replacement fastener where the original screw has stripped, gone missing, or become loose. What it does

• Secures panels, brackets or small components to the appliance frame.
• Restores a rattling or loose panel symptom caused by a missing or damaged fastener.
• Prevents parts from shifting during operation, which can reduce wear or noise.
• Works wherever the OEM screw specification and head style match the original.

• Disconnect power and water before accessing the area.
• Use the correct driver bit to avoid cam-out and head damage.
• Tighten snugly but avoid over-torquing; stripped threads or broken screws can result from excessive force.
• Replace with the same part number or identical size/type to ensure proper fit and function.

Size: 8 x 1/2 ab.

This container roller bearing supports the trash compactor drawer as it slides on its tracks. Replacing a worn bearing restores smooth, quiet movement and helps keep the container aligned for easy opening and closing.

• Provides low-friction support so the drawer glides smoothly on the tracks
• Helps maintain proper container alignment and stability
• Reduces squeaks, grinding, and sticking during operation
• Common symptoms: drawer hard to open/close, scraping noises, binding or uneven movement, visible wear/flat spots on the bearing

• Disconnect power to the compactor before servicing
• Remove and empty the drawer to access the bearing location
• Install the new bearing in the same orientation; transfer any hardware as needed
• Inspect rollers, axles, and tracks; replace any additional worn parts for best results

Fits 15 and 18 inch compactors. This kit is for securing the compactor bags. Kit contains a set of 4 buttons and screws.

This genuine replacement screw restores secure mounting of panels and components on Whirlpool appliances, helping stop loose or rattling parts and maintain proper fit. Small but essential fastener for routine repairs. What it does:

• Secures panels, trim, brackets or small components to appliance frames
• Replaces missing, damaged, or stripped screws that cause loose or misaligned parts
• Helps stop vibration noise and restore proper panel alignment
• Provides the correct thread and length for the original mounting location

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or part damage
• Turn off and unplug the appliance before accessing internal components
• Keep removed fasteners organized so you return them to the original locations