Parts for Kitchenaid KTTS505ESS2: Frame Parts

This is the left side frame slide. For right side use W11722978.

The Roller Assembly is an OEM replacement part for Whirlpool and KitchenAid trash compactors. It includes dual plastic roller drums that grasp and compact trash inside the waste cylinder. The assembly comes with 2 rollers. 

Causes of faulty or worn rollers include years of continuous daily use compressing a wide variety of trash materials. 

Symptoms include:

• Inability to fully compact bags into tight, uniform bricks  
• Loose, inefficient compaction allowing excess empty space
• Excessive odors escaping around poorly compressed bags
• Visible cracking or flat spots on roller gripping surfaces

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 8 x 1/2 ab.

This is a replacement machine screw sized 8-18 x 3/8 that secures panels and components on compatible appliances. It restores proper fastening where a worn, stripped, or missing screw causes loose parts or rattling. What it does

• Fastens control panels, trim pieces, or brackets to the appliance chassis
• Replaces stripped, corroded, or missing screws that cause loose panels or vibrating noise
• Provides correct thread engagement for a secure hold in tapped holes
• Small hardware solution often used during door, console, or interior repairs

• One 8-18 x 3/8 machine screw (quantity: 1)

• Use the correct screw size and thread; do not force a different-size fastener into tapped holes
• Hand-start the screw to avoid cross-threading, then tighten with the appropriate screwdriver
• Disconnect power before accessing internal components or panels on electrical appliances
• If metal threads are damaged, repair with a helicoil or replace the damaged component rather than over-torquing

This safety interlock switch verifies the latch is properly engaged and allows the appliance to run only under safe conditions. Replacing a worn switch restores reliable starting and consistent shutoff when the door is opened.

• Confirms door/latch is closed so the unit can operate safely
• Opens/closes the circuit to the control or power path
• Common symptoms: won't start, must press/hold door to run, stops when the door is jiggled, intermittent operation
• Helps prevent nuisance shutdowns caused by a weak or failing switch

• Disconnect power before servicing; high voltage may be present in some appliances
• Access the switch at the latch/interlock bracket; note wire positions
• Move connectors one at a time and match the original NO/NC orientation
• Ensure the actuator aligns with the latch and the switch is firmly secured before testing

This replacement leveling wheel restores a dryer/washer cabinet's ability to sit level and roll smoothly during adjustment. It helps stop wobble and ensures the appliance can be properly leveled for stable operation. What it does:

• Replaces a worn or broken leveling wheel on the appliance base or leveling assembly
• Allows the cabinet to be adjusted up or down when setting appliance height
• Helps reduce rocking, uneven vibration, and unstable operation caused by a damaged leveler
• Works with the appliance's leveling hardware to keep the cabinet properly supported

• One replacement leveling wheel

• Disconnect power and water before beginning any work
• Support the appliance securely to relieve weight from the leveling assembly before removal
• Remove the old wheel from the leveler shaft and press or snap the new wheel into place; use basic hand tools as needed

This Inner Door Panel forms the interior surface of the dishwasher door. Replacing a dented or corroded panel restores proper sealing and structural support for the latch and dispenser, helping prevent leaks and rattling during wash cycles.

• Creates the interior door surface and directs water back into the tub
• Provides mounting points for the detergent/rinse aid dispenser, door latch, and vent components
• Helps maintain a watertight seal when the door is closed
• Replace if rusted, cracked, warped, or if dispenser/latch mounts are broken; may show leaks at the door or unusual rattling

• Disconnect power and water supply before servicing
• Open the door and remove perimeter screws; support the outer door panel as you separate the panels
• Transfer the dispenser, latch, vent, and any insulation/gaskets from the old panel to the new panel
• Reassemble with even screw torque; verify door closes/seals and run a short test cycle to check for leaks