Parts for Ge JP989SD4SS: 01 - Control Panel & Cooktop Parts

Burner won't heat or stays on constantly? The infinite control switch regulates burner temperature. Simple DIY fix with basic tools in under 30 minutes.

Replace a worn or missing surface burner knob to restore smooth, accurate heat control. This black knob presses onto the surface element switch shaft so you can turn the element on and select cooking temperatures with confidence.

• Attaches to the surface element switch shaft to control On/Off and heat levels
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps when the knob slips, won't stay on, or is hard to set accurately
• Black finish maintains the original appearance

• Turn all controls Off and allow the cooktop to cool before servicing
• Pull the old knob straight off the switch shaft—do not twist or pry the shaft
• Align the new knob with the shaft and press straight on until fully seated
• Verify smooth rotation through the settings before use

This 3-speed blower switch controls the exhaust fan in your range hood, allowing you to select low, medium, or high airflow. Replacing a worn switch can restore dependable ventilation and proper speed control. What it does:

• Selects low, medium, or high fan speed by routing power to the blower motor
• Helps resolve a fan that will not run, runs only on one speed, or will not change speeds
• Can address a switch that feels loose, sticks, or works intermittently

• 1 three-speed blower switch

• Disconnect power at the breaker before servicing
• Access the control area; note wire locations (or take a photo) and transfer wires to the new switch one at a time
• Ensure push-on terminals are fully seated and secure
• Test all fan speeds before reassembly

Replace your cooktop's selector knob if cracked, broken, or missing. This glossy black control knob installs on the control panel to operate settings.

Oven won't change modes or burner won't heat? The selector switch routes power to cooking functions. Moderate DIY repair with video guidance available.

Replace your cooktop indicator light lens when cracked, discolored, or dim. Restores visibility of burner status lights. Verify fit with your model number.

Replace your cooktop indicator light lens when cracked, discolored, or dim. Restores visibility of heating element status. Confirm fit with your model.

Bridge element not heating evenly or failing to connect? This cooktop bridge heating element restores even heat across two burners for large cookware. 1-2 hour install.

Fix a cooktop burner heating only on inner or outer ring, or not heating at all. This dual radiant element restores both heating zones. DIY repair.

Replacement mounting stud for cooktops and ranges. Secures the cooktop assembly to the cabinet or countertop. Replace if broken, stripped, or missing.

This flat washer (.250 inch inner diameter x .812 inch outer diameter) is a simple replacement part that helps distribute load from a fastener and protects mating surfaces for reliable appliance operation. What it does:

• Provides a stable bearing surface for screws, bolts or studs to reduce wear on parts
• Helps distribute clamping force to prevent pull-through or deformation of softer materials
• Reduces vibration and movement at the joint when installed correctly
• Missing or damaged washers can lead to loose fasteners, increased vibration or component misalignment

• Disconnect power and water before servicing the appliance
• Replace like-for-like: inner/outer diameters and thickness match the original washer
• Inspect mating hardware and surfaces for damage; replace corroded or deformed fasteners as needed
• Tighten fasteners evenly and avoid over-torquing to prevent washer or component damage

Mounting bracket that secures the radiant element to your cooktop. Replace if bracket is bent, broken, or missing to properly support the heating element.

Foam seal tape creates an airtight barrier between your cooktop and countertop, preventing spills from dripping into cabinets. Replace when worn or gaps appear.

Replacement thumb screw for securing cooktop panels and components. Hand-tighten without tools for quick access. Replaces worn or missing screws.

Replace your dull, broken, or missing cooktop scraper blade. This cleaning tool blade removes baked-on food and residue from glass cooktop surfaces.

Specially formulated cleaner for ceramic glass and smooth cooktops. Removes cooked-on food, grease, and spills without scratching. Verify fit by model.