Parts for Ge JGBS66EEK2ES: Control Panel & Cooktop Parts

This wire tie secures and organizes wiring inside the appliance to help prevent chafing and loose connections. Its 7-7/8 inch length is suited for bundling harnesses and routing cables away from heat and moving parts. What it does:

• Fastens and groups wires or small hoses to keep them neatly routed
• Helps prevent wire chafing, abrasion, and contact with sharp edges
• Reduces the chance of intermittent connections from loose wiring
• Keeps wiring away from moving components to reduce noise and wear

• Disconnect power before servicing the appliance
• Position wiring as needed, insert tie and tighten; avoid over-tightening
• Trim excess tie length flush and secure cut end away from wires
• Replace any damaged wiring insulation and verify routing before restoring power

Structural end support bracket for gas ranges. Replaces broken, cracked, or missing end support components. Essential for proper range stability and alignment.

End support bracket for gas ranges. Provides structural support at the end of the cooktop assembly. Replace if cracked, bent, or missing to restore stability.

Metal backguard restores rear trim and wall protection on your gas range. Replaces dented, bent, scratched, or rusted backguard above the cooktop.

Fix F4 error codes or an oven that won't heat with this gas range electronic control board. Regulates bake and broil cycles. DIY-friendly repair.

Upper back cover panel for gas ranges. Protects internal components and completes the exterior finish. Replace if cracked, damaged, or missing.

If burners won't ignite automatically but light with a match, the spark module likely failed. Accessed from the back of the range, moderate difficulty.

Fix surface burners that won't ignite or spark continuously with this electrode and harness assembly. Restores proper gas ignition on range cooktops.

Replacement grate assembly for gas range stovetops. Provides stable cooking surface over burners. Order if your existing grate is cracked, broken, or worn.

Fix a wobbly or misaligned cooktop with this rangetop and bracket assembly. Secures the cooktop to your gas range, restoring stable cooking surface.

Replacement center burner grate for gas ranges. Restores a stable cooking surface over the middle burner when the original is cracked, worn, or missing.

Factory screw secures brackets, panels, trim, or burner components on ranges, cooktops, and wall ovens. Replaces missing, stripped, or corroded fasteners.

This backguard eyebrow is the top trim piece that finishes the range's control panel area, restoring appearance and protecting the backguard edge from spills and heat. It provides a clean factory look for worn or damaged trim. What it does:

• Covers and protects the upper edge of the range backguard and control area
• Restores a finished appearance when the original trim is dented, scratched, or missing
• Helps reduce buildup of grease at the top of the control panel
• Matches OEM fit and mounting points for a direct replacement

• One backguard eyebrow trim piece

• Remove power to the appliance before beginning service
• Basic hand tools typically required; handle trim carefully to avoid scratching finish
• Follow OEM instructions for proper alignment and secure mounting

Control panel overlay for gas ranges. Installs over the control panel to protect electronics and enhance appearance. Replace if cracked, peeling, or worn.

Medium burner cap for gas cooktops and ranges. Sits atop the burner head to distribute flame evenly. Replace if cracked, chipped, or worn from use.

Burner cap covers the burner head and distributes flame evenly on gas ranges and cooktops. Replace if cracked, warped, or missing for proper cooking.

Replacement burner cap for gas cooktops and ranges. Sits atop the burner head to distribute flame evenly. Replace if cracked, chipped, or worn.

Burner cap assembly covers the burner head on gas cooktops and ranges. Replace cracked, stained, corroded, or missing caps to restore appearance.

Replacement small surface burner for gas ranges and cooktops. Restores proper flame control when original burner is damaged, cracked, or corroded.

The Burner, Large V2 is an OEM part for GE gas ranges. It is designed to provide a consistent and even flame for cooking, ensuring efficient heat distribution for large pots and pans.

Causes of a bad burner can include clogging from food spills

Replacement burner head for gas ranges and cooktops. Installs on stovetop to distribute flame evenly. Replace if warped, cracked, or causing uneven flames.

Oval burner assembly for gas range cooktops. Replace if your burner head or cap is cracked, clogged, damaged, or missing. Includes both burner and cap.

Medium-sized surface burner for gas cooktops and ranges. Installs on the cooktop surface. Replace if cracked, worn, or providing uneven heat distribution.

If your gas range burner won't light or clicks continuously, this igniter clip secures the ignition system. Simple DIY fix in under 15 minutes.

This is a replacement screw that can be used with many different types of household appliances. Screws fasten various pieces of machines together. They can also help to reduce the amount of vibration in the machine. If a screw is missing or damaged, it co

Protective bumper that cushions the burner grate and prevents scratching or denting the cooktop surface. Replace if cracked, worn, or missing.

Package of 12

This is the flat griddle plate that sits over the center burners on compatible cooktops/ranges. It provides an even cooking surface for pancakes, sandwiches, and more, and replaces a worn or missing griddle so heat is distributed properly.

• Creat

Hex washer head screw for electric ranges. Secures panels, brackets, and internal components. Replace if screw is stripped, missing, or damaged.