Parts for Lg WM3555HWA/00: Control Panel & Dispenser Assy Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This exhaust duct directs hot, moist air from the dryer to the external vent, helping maintain proper airflow and prevent moisture buildup. It's a direct-replacement duct designed to restore proper venting and reduce dryer run-time caused by restricted airflow. What it does:

• Channels dryer exhaust from the drum to the home vent to help maintain efficient airflow
• Helps reduce moisture and lint buildup in the dryer cabinet and vent path
• Can improve drying performance when a damaged or cracked duct is replaced
• May reduce excessive heat or unusual odors that occur with a broken or disconnected duct

• One exhaust duct

• Disconnect power and gas before starting any dryer service
• Inspect surrounding seals and clamps and replace if damaged; use manufacturer-recommended fasteners
• Ensure duct is routed without sharp kinks and secured to the dryer and wall vent to prevent leaks

This cabinet assembly replaces a damaged or worn outer cabinet to restore the appliance's structure and appearance. It provides the external housing that supports controls, panels and internal components for safe, stable operation. What it does:

• Replaces cracked, dented or corroded outer housing that exposes internal parts
• Restores proper panel alignment and door/frame fit to reduce rattles and vibration
• Protects internal components from dust, moisture and physical damage
• Helps maintain the appliance's original appearance and mounting points for controls

• Disconnect power (and shut off water/gas, if applicable) before beginning any service.
• Use caution lifting large panels; two people may be required to remove/install the cabinet safely.
• Retain and re-use any brackets, screws or trim pieces unless the replacement explicitly includes them.

This display power control board assembly operates the user interface and display lighting so control buttons and status indicators respond correctly. Replace a damaged board to restore display visibility and normal control-panel operation. What it does

• Powers and drives the control-panel display and associated LEDs.
• Processes user inputs from touchpads or buttons so settings register.
• Can cause unresponsive controls, blank or flickering display, or no display lighting when failing.
• Works with the main control system to show error codes and status indicators.

• Disconnect power to the appliance before starting; verify mains are off.
• Handle the board by the edges and avoid static discharge; use an ESD strap if available.
• Keep screws and wiring organized; note connector locations before removal.

This factory bolt assembly fastens critical components securely inside your appliance. Replacing a worn, stripped, or missing bolt restores a snug fit, reduces vibration and noise, and helps prevent damage caused by loosening during operation. What it does:

• Secures mating parts to maintain alignment and structural stability
• Helps prevent vibration, rattling, and movement from a loose fastener
• Addresses issues like wobble or intermittent operation in the affected area
• Replaces damaged, corroded, or missing hardware for a reliable hold

• One bolt assembly

• Disconnect power before servicing
• Support the assembly being fastened to avoid strain or misalignment
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening
• Replace companion washers or hardware if worn or damaged; match any threadlocker used on the original

The Tub Seal Gasket is an OEM part for LG washing machines. It creates a tight seal between the inner and outer tubs during the wash cycle, preventing leaks and containing water. The gasket helps prevent water from escaping the tub. 

Causes of a bad gasket can include wear and tear from repeated use over time, exposure to cleaning chemicals or extreme temperatures, or damage from handling heavy loads. 

Symptoms of a bad gasket include: 

• Water leaking from the outer tub during operation
• Excessive moisture in areas surrounding the washer 
• The tub making creaking or grinding noises
• Decreased washing or spinning performance

This OEM LG part can also be used on Kenmore/Sears appliances. 

A replacement clamp assembly that secures flexible hoses or tubing to fittings to help prevent leaks and minimize movement. Fits OEM mounting points and restores a tight hose connection for reliable operation. What it does:

• Secures a water or drain hose to a nipple or fitting to stop slipping and reduce leaks
• Helps maintain a sealed connection under normal pressure and vibration
• Reduces hose movement that can cause wear, noise or intermittent leaks
• Useful when the original clamp is corroded, damaged or no longer holds tightly

• Turn off power and shut off water supply before starting work
• Inspect hose and fitting; replace hose if damaged or excessively worn
• Use appropriate pliers or a screwdriver to remove/install the clamp; avoid over-tightening

The Door Strike is an OEM part for LG washing machines. This part ensures that the door closes securely and the washer can operate safely. 

Causes of a bad door strike can include regular wear and tear from frequent use, impact or mishandling that leads to bending or breaking, or issues with the door alignment that cause undue stress on the strike. 

Symptoms of a bad Door Strike include:

• The door not latching properly
• The washer not starting or stopping mid-cycle due to door issues
• Leaks around the door during operation
• Visible damage or wear to the strike

This OEM LG part is also compatible with some Kenmore models.

This inner microwave door glass replaces cracked, chipped or broken door glass to restore clear viewing and help maintain safe operation. Precision-fit replacement for the door assembly on compatible units. What it does

• Replaces damaged or shattered door glass so you can see cooking progress
• Helps maintain proper heat containment and door integrity when installed correctly
• Stops rattling or air leaks caused by cracked or loose glass
• Prevents safety risks from exposed sharp edges on broken glass

• One door glass

• Disconnect power to the appliance before starting any repair
• Handle glass with care and wear protective gloves and eye protection
• Follow the OEM service manual or exploded parts diagram for door disassembly and reassembly
• If the door frame, hinges, or latch are damaged, replace or inspect those components before reinstalling the glass.

This water inlet valve assembly controls water flow into the washer, restoring normal fill and cycle operation when the valve fails. Replaces a worn or leaking inlet valve to stop overfilling, no-fill, or slow-fill symptoms. What it does:

• Directs cold and/or hot water into the tub when the washer calls for fill
• Opens and closes via solenoids to control fill timing and volume
• Commonly replaced for leaks at the valve, no water entering tub, or continuous filling
• Works with the washer's control board to regulate water during cycles

• One water inlet valve assembly

• Disconnect power and shut off water supply before starting any work
• Drain remaining water from hoses and tub to avoid spills
• Inspect and replace inlet hoses and clamps if damaged; hand-tighten fittings to avoid leaks
• Test the machine through a short cycle after installation and check for leaks

The Inlet Valve Assembly is an OEM part for LG front-loading washing machines. It is a critical component that controls water flow into the washer tub. Comprised of durable solenoid valves and precision sealing elements, the inlet valve assembly works automatically to supply the appropriate amounts of hot and cold water at predetermined stages in each cycle. 

Causes of a bad inlet valve can include mineral buildup obstructing valve ports over time, worn valve seals resulting in water leaks, or electrical faults preventing the solenoids from opening and closing reliably.

Symptoms of a bad inlet valve assembly include:

• The washer failing to fill with water 
• Uneven or unbalanced water temperature
• Water leaks at the valve connections
• Error codes related to water level or temperature detection

This OEM LG part is also compatible with Sears/Kenmore front-load washers. 
 

This base bracket is a structural mounting support that stabilizes and secures appliance panels or assemblies to the cabinet, restoring proper alignment and preventing excess movement. Fits as a direct replacement mounting bracket. What it does

• Provides stable support for appliance panels/assemblies to reduce rattling and misalignment
• Keeps the cabinet and attached components properly positioned during operation
• Replaces cracked, bent, or missing brackets that can cause vibration or uneven gaps
• Helps restore normal door/panel fit and overall unit stability

• One base bracket

• Always unplug the appliance (and shut off water supply if applicable) before beginning work
• Basic hand tools required; keep track of removed fasteners for reassembly
• Inspect surrounding mounts and hardware; replace any stripped or damaged screws
• Wear gloves to avoid cuts on sharp sheet-metal edges and test fit before final tightening

This Thermostat Assembly monitors and regulates internal temperature within the appliance's heating circuit. Replacing a failed thermostat restores proper heat control, helps prevent overheating, and can resolve common heating performance issues so cycles run correctly. What it does

• Senses internal temperature and opens/closes the heater circuit to maintain proper heat
• Provides over-temperature protection by cutting power at unsafe temperatures
• Helps ensure consistent heating performance throughout the cycle
• Helps with symptoms such as no heat, overheating/shutting off, or unusually long cycle times

• 1 thermostat assembly

• Disconnect power before servicing; allow hot components to cool
• Access the thermostat location (varies by model); note wire positions before removal
• Mount flush to the surface for accurate sensing; transfer original hardware if required
• After installation, test operation; use a multimeter for continuity checks if needed

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This inlet hose routes household water into the appliance so it can fill and operate correctly. Replacing a damaged inlet hose restores proper water flow and prevents leaks that can cause poor performance or water damage. What it does:

• Channels incoming water from the household supply into the appliance
• Stops leaks and restores normal fill when the original hose is cracked, split, or worn
• Helps correct symptoms like no water entering the appliance, slow or intermittent fill, or visible leaking at the hose connection
• Works with the appliance's valve and fittings to maintain a sealed water path

• Turn off the water supply and unplug the appliance before starting any work
• Inspect fittings and seals; replace any worn gaskets to ensure a watertight connection
• Hand-tighten connections then check for leaks; avoid overtightening plastic fittings

This drain hose cap seals and secures the refrigerator defrost drain outlet so meltwater is directed into the drain hose instead of pooling in the cabinet. Replaces a worn or damaged cap to help stop interior leaks and water buildup. What it does:

• Seals the defrost drain outlet to prevent water from spilling into drawers or onto shelves.
• Guides defrost/meltwater into the drain hose and toward the drain pan.
• Helps reduce odors and pests entering through an open drain opening.
• Fits onto the drain outlet to replace cracked, missing, or loose caps.

• Disconnect power before working inside the refrigerator to avoid electrical hazard.
• Remove shelves and drawers as needed to access the drain outlet; clear any visible debris or ice first.
• Press the cap firmly onto the drain outlet/hose until fully seated; avoid excessive force or prying tools.
• After installation, pour a small amount of warm water down the drain to confirm proper flow and seating.

This flexible door boot gasket forms the watertight seal between the washer door and tub to keep water inside during cycles. Replaces a torn, stretched, or worn bellows to stop leaks and restore a secure door seal. What it does:

• Seals the washer door to prevent water from leaking during wash and rinse cycles.
• Compensates for movement between the door and tub while maintaining a watertight barrier.
• Commonly needed when the bellows shows visible tears, cracks, or heavy wear.
• Helps reduce water pooling and mildew buildup caused by gaps or pinholes.

• Disconnect power and water supply before starting any repair.
• Inspect the tub and door mating surfaces; clean before installing the new bellows for a proper seal.
• Some models use internal clamps or retaining rings—retainers must be reinstalled or replaced exactly as removed.

The Washer Heater Assembly is an OEM component specifically designed for LG washing machines. It provides heated water to wash cycles, helping activate detergents and release tough soils for deeper cleaning. 

Causes of a faulty heater assembly typically include cracks in the heater element from chemical exposure or thermal expansion/contraction cycles over time. Electrical connections can corrode from mineral deposits.

Symptoms of a bad heater assembly include: 

• Inability to select hot water cycles  
• Slow or incomplete activation of detergents
• Reduced cleaning performance on heavily soiled loads
• Error codes indicating temperature sensor problems

This OEM LG part is also compatible with select Sears/Kenmore washers.

This DC pump motor assembly drives the appliance pump to move and remove water during drain and circulation cycles. It restores pump operation so the washer/dishwasher can empty properly and avoid standing water. What it does:

• Powers the drain/recirculation pump to move water out of the tub during drain and wash cycles.
• Common repair when the appliance fails to drain, leaves standing water, or shows drain-related errors.
• Helps restore normal water flow for wash, rinse and drain sequences.

• Disconnect power (and water, if applicable) before servicing the appliance.
• Inspect hoses, filters and the pump housing for clogs before replacing the motor.
• Note connector orientation and mounting location; transfer gaskets/seals if the original must be reused.

The Drain Hose is an OEM part for LG washing machines. It is designed to carry used water from the washing machine to the household drain. This hose ensures that water is efficiently expelled from the washer, preventing any overflow or leakage issues.

Causes of a bad drain hose can include cracks or splits due to wear and tear, clogs from debris or residue buildup, and damage from mishandling or improper installation. Such issues can compromise the hose's ability to transport water effectively.

Symptoms of a bad Drain Hose include:

• Water leaks during or after the wash cycle
• The washer not draining properly
• Visible cracks or damage to the hose
• Unpleasant odors due to trapped debris or standing water

This OEM LG part is also compatible with Sears/Kenmore models.

This pump casing is the molded housing that supports and channels the washer's drain pump, ensuring water flows from the tub to the drain. Replacing a damaged casing restores proper drainage and helps prevent leaks. What it does:

• Houses the drain pump and impeller, keeping moving parts aligned
• Directs wastewater from the tub to the drain line
• Seals and contains pump flow to prevent leaks when intact
• A cracked or damaged casing can cause leaks, poor drainage, or unusual noises

• Disconnect power and turn off the water supply before starting work
• Drain remaining water from the washer to avoid spills when removing the pump
• Access typically requires removing a front or rear service panel—support the machine as needed
• Inspect and replace any worn gaskets or seals during reassembly; test for leaks after installation

This drain pump assembly removes and directs wash water out of the tub so cycles can complete and clothes can drain. Replaces a failed pump to restore normal draining and cycle completion. What it does:

• Pumps water from the washer tub to the drain during drain and spin cycles.
• Commonly replaces pumps that cause standing water or failure to drain.
• Can resolve loud grinding or humming from the pump area and drain-related error codes.
• Compatible when the original pump assembly is corroded, clogged, or electrically failed.

• Disconnect power and turn off water supply before starting any repair.
• Drain remaining water from the washer to avoid spills when accessing the pump.
• Remove the service panel to access and replace the pump; note hose and wiring positions for reassembly.
• Handle the pump and impeller gently; secure all hose clamps and electrical connectors before testing.

The Pressure Switch Assembly is an OEM part for LG washers. This pressure switch plays a crucial role in monitoring the pressure levels within the washer tub during various cycles and phases of operation. It is designed to open and close electrical circuits precisely based on pressure readings, signaling the control board to advance the program as needed. 

Symptoms of a bad pressure switch include:

• Inability to complete cycles 
• Error codes related to pressure 
• Repeatedly stopping or not starting cycles
• Strange noises or vibrations 

Causes of failure can include cracks, corrosion or wear over prolonged use. Replace yours today with this genuine LG part to restore optimal functioning and performance.

This OEM LG part is also compatible with Sears/Kenmore.

The Holder is an OEM part for LG front-loading washing machines. It is a plastic mounting bracket or suspension system that attaches to the rear of the washer tub and helps secure internal components like hoses, pulleys, and the rear bearing in place during spin cycles. Subject to force and vibration, the holder must withstand years of washing use.

Symptoms of a bad holder include: 

• Loosening or detaching internal parts leading to noise and imbalance
• Cracking or damage of the plastic bracketry 
• Bearing or tub damage from improperly secured components

Causes can be fatigue from repeated wash cycles, stress cracks from heavy loads, or material deterioration over time. Replace with this OEM LG holder to maintain drum balance and suspend components securely. It is also compatible with Sears/Kenmore front-load washers.

This hanger assembly replaces a worn or broken pivot that helps support and guide a refrigerator/freezer door. Restores proper door alignment and smooth opening so the seal closes correctly and the door operates as intended. What it does:

• Provides the pivot point that supports the door and enables smooth swing motion
• Keeps door aligned to maintain an effective gasket seal and prevent drafts
• Replaces worn, cracked, or bent pivot hardware that can cause uneven or binding doors
• Works with the existing hinge components to restore stable door operation

• Disconnect power and remove any stored items from the door before starting
• Support the door during removal to prevent dropping or damage to the cabinet
• Use basic hand tools; avoid over-tightening fasteners to prevent stress on the part
• If alignment issues persist after replacement, check hinge and strike components for wear

This clamp assembly secures a hose or component to its mounting point to help prevent leaks and reduce vibration. It replaces a worn or broken clamp so the connection stays tight and stable. What it does:

• Secures hoses, lines, or parts to their mounting points to maintain a sealed connection
• Helps reduce vibration and movement that can cause wear or noise
• Restores proper fit where a cracked, bent, or missing clamp allows leaks or misalignment
• Simple, direct replacement—matches the OEM attachment function

• Disconnect power and water before servicing to avoid shock or flooding
• Inspect mating surfaces and hose condition; replace hose if damaged before installing clamp
• Use pliers or a screwdriver as needed; tighten to a snug fit—do not over-tighten
• Follow the appliance's service manual for disassembly/reassembly guidance and safety

This tub clamp secures the washer tub assembly or related hoses to keep components aligned and reduce movement during operation. It helps restore proper fitment so the tub stays stable and functions quietly. What it does:

• Holds the tub or tub-related components in place to prevent shifting during cycles
• Helps reduce vibration and noise caused by loose tub mounting
• Maintains correct alignment of hoses and seals to reduce leak risk
• Used when a worn or broken clamp allows excessive tub movement

• One tub clamp

• Turn off power and water supply before beginning any repair
• Inspect surrounding components (hose, seal, mounting points) and replace if damaged
• Use common hand tools; secure clamp evenly to avoid twisting the tub or hoses

This door boot gasket forms the flexible seal between the outer tub and cabinet opening on a front-load washer to keep wash water contained. Replace a torn or moldy boot to stop leaks and lingering odors.

• Creates a watertight seal between the outer tub and the door opening
• Flexes with drum movement to maintain a reliable barrier during wash and spin
• Helps resolve leaks at the door, visible rips or cracks, water on the floor after a cycle, and musty smells that persist after cleaning

• Unplug the washer and turn off water supply before servicing
• Remove the front panel as needed; note the boot's orientation before removal
• Clean mounting grooves; seat the new boot evenly all the way around and secure clamps firmly
• Run a quick cycle to check for leaks after reassembly

A replacement nozzle assembly that restores proper spray direction and flow for compatible LG machines. Replaces a damaged, cracked, or clogged nozzle to help improve water/detergent distribution and performance. What it does

• Directs and focuses water or solution flow for effective cleaning or dispensing.
• Replaces nozzles that are cracked, worn, or blocked and causing weak or misdirected spray.
• Helps reduce spotting or poor cleaning caused by uneven spray coverage.
• Matches OEM fit and form to sit correctly in the dispenser/spray manifold area.

• One nozzle assembly

• Disconnect power and water supply before starting any repair.
• Remove the appropriate cover or access panel to reach the nozzle assembly per your model's service instructions.
• Replace the part carefully; confirm correct orientation and secure any clips or fasteners.

This inlet hose supplies water from the household supply to the appliance's fill system, helping the unit fill normally and preventing leaks. Durable replacement for worn, cracked, or leaking inlet connections. What it does:

• Carries cold (or hot) water from the house supply to the appliance's fill valve and tub.
• Seals the connection at the water valve to prevent drips or leaks.
• Restores normal fill behavior when a damaged or collapsed hose causes slow or no fill.
• Helps stop water on the floor caused by cracked, split, or degraded hose material.

• Turn off water supply and unplug the appliance before replacing the hose.
• Inspect mating fittings and replace worn O-rings or gaskets as needed; only state included items above.
• Hand-start threads to avoid cross-threading, then snug with a wrench — do not overtighten.
• Check carefully for leaks after restoring water and power.

Connector hose joins an appliance water line to internal plumbing, providing a sealed path for water. Replacing a damaged connector stops leaks and restores reliable water delivery to dispensers and ice makers.

• Joins and seals the appliance water line to the unit, preventing leaks and ensuring proper flow.
• Replace when you notice dripping, pooling under the appliance, or reduced water/ice production.
• Fits factory connection points for a secure, leak-resistant seal.
• Works with existing clamps and O-rings when those components are serviceable.

• Shut off the water supply and disconnect power before removing the old connector.
• Relieve water pressure by running the dispenser or dispensing water before disconnecting lines.
• Inspect and replace worn clamps or O-rings; hand-tighten fittings, then turn the water on slowly and check for leaks.

This washer shock absorber mounts between the outer tub and base to control movement during spin. Replacing a worn damper restores stability, reduces vibration and noise, and helps prevent the machine from walking or banging.

• Stabilizes the tub during spin by absorbing and controlling movement
• Reduces vibration and cabinet noise for smoother operation
• Helps the washer reach and maintain proper spin speed
• Worn shocks can cause shaking, banging, or walking during spin

• Disconnect power and water; use gloves and protect the floor.
• Access from the front or rear depending on model; remove panels as needed.
• Support the tub, then remove fasteners at both ends; install the new damper in the same orientation and tighten securely.
• Reassemble, level the washer, and run a test spin to check for vibration.

The Hinge Pin is an OEM part for LG washing machines. It serves as a pivot point for the washer door, allowing it to open and close smoothly. This component is crucial for maintaining the proper alignment and function of the washer door, ensuring a secure and reliable seal during operation.

Common causes of a bad hinge pin include frequent use leading to wear and tear, physical damage from accidental impacts, or rust and corrosion over time. A compromised hinge pin can result in misalignment of the door, affecting the washing machine's ability to close properly and maintain an effective seal.

Symptoms of a bad hinge pin include:

• Difficulty opening or closing the washer door
• Door not staying securely closed during operation
• Squeaking or grinding noises when the door is moved
• Visible wear or damage to the hinge pin

This OEM LG part is also compatible with Sears/Kenmore models.

The Vent Hose is an OEM part for LG washing machines. This hose is essential for ensuring proper ventilation within the washer, allowing air to circulate and preventing the buildup of moisture and mildew. It helps maintain the efficiency of the washing machine by facilitating the expulsion of air and excess water vapor during operation.

Causes of a bad washer vent hose can include wear and tear over time, blockages from lint or debris, or damage due to bending or pinching.

Symptoms of a bad vent hose include:

• Excessive moisture or condensation inside the washer
• Musty odors from the washing machine
• Visible cracks or holes in the hose
• Poor ventilation leading to inefficient washing cycles

This OEM LG part is also compatible with Sears/Kenmore.

This mesh filter assembly captures debris before it reaches the refrigerator's water/ice path, helping maintain clean water flow and reduce clogging. Replace a damaged or clogged mesh filter to restore normal water/ice performance. What it does:

• Screens out mineral particles and sediment from the water/ice supply to prevent clogs
• Helps reduce debris in ice and water dispensed from the refrigerator
• Can improve weak or intermittent water flow when the mesh is clogged or torn
• Prevents foreign particles from reaching valves and the ice maker inlet

• One mesh filter assembly

• Turn off water supply and unplug the refrigerator before servicing
• Remove the old filter assembly and install the new mesh filter in the same orientation
• Handle the filter gently; avoid tearing the mesh during installation

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.