Parts for Crosley CFWH7300RW0: Control Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This is the main electronic control board that manages the washer's cycles, timing, and user interface functions. It receives input from the control panel and sends signals to components like the motor, valves, and sensors. Replace this board if the washer fails to start, displays error codes, has unresponsive buttons, or stops mid-cycle unexpectedly.

Mounting bracket for washer and laundry center models. Secures components in place during operation. Replace if cracked, bent, or broken to restore stability.

This small pin secures the program selection knob to the dryer's control panel shaft. Replace if the control knob spins freely without changing settings or falls off the control panel.

Fix a washer that won't fill, overfills, or shows E35 error code with this water level pressure switch. Moderate DIY repair takes about 1-2 hours.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Washer won't start, shows error codes, or cycles incorrectly? The control board manages all wash cycles and safety functions. Moderate DIY repair.

Wire harness assembly for washers and laundry centers. Replaces damaged, frayed, or corroded wiring connections. Essential for restoring internal electrical routing.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet panels, brackets, or internal parts in washers and dryers
• Direct replacement for worn or lost screws to keep assemblies aligned and secure
• Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
• Spec: #10-16 thread; 0.75-inch length

• Disconnect power; for washers, also shut off water supply
• Match the original screw location; start threads by hand to prevent cross-threading
• Use a driver that fits the screw head properly; tighten snugly without overtightening

Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

Fix a washer that fills slowly, won't fill, or leaks water when off with this water inlet valve. DIY repair takes about 30 minutes with basic tools.

Connects the detergent dispenser to the wash tub in your washer. Replace if cracked, leaking, or causing water damage to other components during cycles.

Secures hoses to fittings, preventing leaks in water and drain lines. Replace when connections loosen or leaks appear. Verify fit with your model number.

Direct-fit outer cabinet housing that encases and protects internal washer components. Replace if cracked, damaged, or worn to restore proper alignment.

Rubber O-ring seal prevents water leaks at hose connections and fittings. Replace when worn or cracked to restore tight seal and stop dripping. Verify fit.

Fix a broken or missing detergent dispenser cover that's cracked or won't guide proper detergent placement. Simple 5-minute replacement repair.

Detergent drawer broken, cracked, or won't open? This drawer holds and dispenses detergent during wash cycles. Simple snap-in replacement, no tools needed.

Fix a broken or cracked dispenser drawer handle that won't open properly. Simple snap-in replacement takes minutes. Fits front load washers.

This is the complete detergent dispenser drawer assembly for a front-load or top-load washing machine. It holds and dispenses detergent, fabric softener, and bleach at the appropriate times during the wash cycle. Replace this assembly if the dispenser drawer is cracked, if detergent is not dispensing properly, or if residue builds up and cannot be cleaned out.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Seals hot and cold water connections to your washer's dispenser. Replace if you notice leaking at the inlet assembly. Confirm fit with your model number.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.