Parts for Electrolux EFLS517STT0: 02 - Control Panel Parts

Fix unresponsive buttons or blank displays with this user interface control board. Restores keypad function and display readings on your laundry center.

Replacement mounting bracket that secures panels, assemblies, or controls to your washer cabinet. Needed when original is cracked, broken, or missing.

Control knob assembly for laundry center washers. Replacement needed when knob is cracked, broken, loose, or missing from repeated use or damage.

Fix uneven drying or excess noise with this air flow diffuser. Directs airflow inside your dryer for consistent temperature and quieter operation.

Fix E11 error code and washer not filling issues. This pressure sensor switch monitors water levels and signals the control board. DIY repair in under an hour.

Secures the drum baffle (lifter vane) to your washer drum. Replace missing, stripped, or loose screws to keep baffles firmly attached and prevent rattling.

Mounting screw for dryers and laundry appliances. Secures panels, brackets, and internal components. Replace if stripped, missing, or damaged.

Fix E11 error codes, no-fill issues, or washer won't start. This main control board manages all wash cycles. Moderate difficulty repair, 1-2 hours.

The Console Assembly with Overlay is an OEM part for Frigidaire washing machines. Mounting to the top of the unit provides outer protection for the control panel and touchpad located behind.

Causes of failure are normal wear from repeated use and cleaning chemicals, as well as potential warping from prolonged heat and moisture exposure inside the unit.

Signs of a bad console assembly include:

• Broken, cracked, or improperly fitting outer overlay  
• Exposed internal padding or frame
• Loose, misaligned, or bubbled overlay veneer
• Faded or stained surfaces looking worn over time

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Replacement drain hose for front-load washers. Connects the pump to the drain outlet. Replace if cracked, kinked, leaking, or damaged to restore drainage.

Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.

Secures wiring and hoses to your laundry center frame. Replace if cracked, broken, or missing to keep wire bundles organized and protected from wear.

Washer won't fill with water or only fills with cold? This water inlet valve controls water flow into the tub. DIY-friendly repair in about 30 minutes.

Replaces cracked, worn, or leaking internal water hose in your washer. Restores watertight water flow between drum and dispenser components.

Secures hoses to fittings, preventing leaks in water and drain lines. Replace when connections loosen or leaks appear. Verify fit with your model number.

Rubber O-ring seal prevents water leaks at hose connections and fittings. Replace when worn or cracked to restore tight seal and stop dripping. Verify fit.

Replaces missing, stripped, or rusted 8-18 thread screws that secure dryer panels, brackets, and components for tight, rattle-free assembly.

Replacement indicator light for laundry center control panels. Restores visual feedback when panel lights fail or dim. Confirm fit with your model number.

Fix detergent not dispensing or pooling in the cup. This washer dispenser cup restores proper detergent flow. Easy DIY repair in under 30 minutes.

A replacement drawer slide that helps the drawer open and close smoothly and stay aligned. Restores reliable sliding action for drawers that stick, sag, or catch while opening and closing. What it does:

• Guides and supports the drawer for smooth, even movement
• Prevents drawer sagging and misalignment during use
• Reduces sticking, scraping, or catching when opening or closing
• Helps maintain proper drawer fit and load distribution

What's included: One replacement slide Install notes:

• Disconnect power and remove drawer before replacing the slide
• Inspect mounting clips or screws and reuse or replace as needed; align slide before securing
• Use proper tools and avoid forcing parts to prevent damage

Mounting screw for washer cabinet and component assembly. Replace if screw is stripped, missing, or damaged during disassembly. Essential hardware piece.

Metal sheet-metal screw secures panels, brackets, and internal components. Replace when missing, stripped, or damaged to restore proper fit.

Seals hot and cold water connections to your washer's dispenser. Replace if you notice leaking at the inlet assembly. Confirm fit with your model number.