Parts for Electrolux EIFLS55QT0: Control Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Mounting bracket for washer and laundry center models. Secures components in place during operation. Replace if cracked, bent, or broken to restore stability.

Control knob ring for dryers. Installs on the control panel to secure and finish the dial assembly. Replace if cracked, broken, or missing.

Replacement display lens for dryer control panel. Covers and protects indicator lights. Install when original lens is cracked, discolored, or missing.

Replacement control panel button for your washer. Installs on the front console. Needed when original button is cracked, broken, or missing.

Fix a washer that won't start, locks unexpectedly, or doesn't respond to buttons. This control board assembly restores electronic functions and display.

Fix a washer that won't fill, overfills, or shows E35 error code with this water level pressure switch. Moderate DIY repair takes about 1-2 hours.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Fixes washer not responding to buttons, blank display, or error codes. Restores console functions and cycle selection. Moderate DIY repair, 30-60 minutes.

Replacement wire harness cable for your washer. Connects electrical components inside the machine. Needed when the original cable is damaged or worn.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Machine screw secures panels, brackets, and internal components in washers. Replace missing, rusted, or stripped screws to restore proper fit and alignment.

This is a flexible hose that connects the detergent or fabric softener dispenser to the wash tub, allowing dispensed products to flow into the drum during the wash cycle. If you notice detergent not dispensing properly, leaking near the dispenser area, or water pooling under the washer during the fill cycle, this hose may be cracked, clogged, or disconnected and needs replacement.

Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

This is a water inlet valve that controls the flow of hot and cold water into the washing machine tub during the fill cycle. It is an electrically operated solenoid valve that opens and closes based on signals from the control board. Replace this valve if your washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it shouldn't be.

Replaces cracked, worn, or leaking internal water hose in your washer. Restores watertight water flow between drum and dispenser components.

Secures hoses to fittings, preventing leaks in water and drain lines. Replace when connections loosen or leaks appear. Verify fit with your model number.

Rubber O-ring seal prevents water leaks at hose connections and fittings. Replace when worn or cracked to restore tight seal and stop dripping. Verify fit.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This small cup fits inside the washer's dispenser drawer and holds liquid detergent, releasing it into the wash drum at the appropriate time during the cycle. It is designed to meter out the correct amount of detergent for optimal cleaning. Replace if the cup is cracked, warped, or missing, or if detergent is not dispensing properly during the wash cycle.

A replacement drawer slide that helps the drawer open and close smoothly and stay aligned. Restores reliable sliding action for drawers that stick, sag, or catch while opening and closing. What it does:

• Guides and supports the drawer for smooth, even movement
• Prevents drawer sagging and misalignment during use
• Reduces sticking, scraping, or catching when opening or closing
• Helps maintain proper drawer fit and load distribution

What's included: One replacement slide Install notes:

• Disconnect power and remove drawer before replacing the slide
• Inspect mounting clips or screws and reuse or replace as needed; align slide before securing
• Use proper tools and avoid forcing parts to prevent damage

This drawer glide helps your washer's detergent or fabric softener drawer slide smoothly in and out. It supports the drawer weight and ensures proper alignment for dispensing cycles. Replace when the drawer sticks, doesn't close properly, or falls out of its tracks.

This conveyor mechanism moves the dispenser drawer smoothly in and out of your washing machine during operation. It ensures proper alignment and movement when the drawer opens and closes to add detergent and fabric softener. If your dispenser drawer sticks, won't open properly, or has become misaligned, this conveyor component needs replacement.

Metal sheet-metal screw secures panels, brackets, and internal components. Replace when missing, stripped, or damaged to restore proper fit.

Seals hot and cold water connections to your washer's dispenser. Replace if you notice leaking at the inlet assembly. Confirm fit with your model number.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.