Parts for Electrolux ELFW7337AW0: Control Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Fix a washer that won't start, stops mid-cycle, or shows error codes with this electronic control board. Restores proper cycle control and settings.

Replacement mounting bracket that secures panels, assemblies, or controls to your washer cabinet. Needed when original is cracked, broken, or missing.

This replacement door gasket seals the appliance door to maintain a tight, even seal that helps control temperature and prevent leaks. It restores proper door closure and reduces energy loss when the original gasket is cracked, torn, or hardened. What it does:

• Creates a continuous barrier between the door and cabinet to keep internal air in and outside air out
• Prevents water and air leaks that can lead to frost build-up or inconsistent temperatures
• Improves appliance efficiency by reducing cold/hot air exchange across the door
• Helps the door latch and close evenly for reliable operation

• One door gasket/seal

• Disconnect power to the appliance before starting any repairs
• Remove the old gasket by gently pulling from the door frame; clean the gasket channel before installing the new seal
• Work around the door evenly, pressing the new gasket into the channel to avoid stretching or twisting
• If the gasket is tight after install, allow time for it to relax into place; use care with sharp tools to avoid damage

Fix E11 error code and washer not filling issues. This pressure sensor switch monitors water levels and signals the control board. DIY repair in under an hour.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

If your washer won't start, buttons don't respond, or the display is blank, the control board may have failed. This assembly restores cycle selection and timing.

Replacement control console assembly with handle for your washer. Restores the front panel interface when the original is cracked, damaged, or broken.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

This assembly combines the dispenser housing with the water inlet valve, controlling the flow of water into the washer's detergent and softener dispensers. It mounts at the back of the machine where the water supply hoses connect. Replace this assembly if the washer is not filling properly, water leaks from the back, or detergent is not being dispensed correctly during the wash cycle.

Replaces cracked, worn, or leaking internal water hose in your washer. Restores watertight water flow between drum and dispenser components.

Secures hoses to fittings, preventing leaks in water and drain lines. Replace when connections loosen or leaks appear. Verify fit with your model number.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This assembly combines the dispenser housing with the water inlet valve, controlling the flow of water into the washer's detergent and softener dispensers. It mounts at the back of the machine where the water supply hoses connect. Replace this assembly if the washer is not filling properly, water leaks from the back, or detergent is not being dispensed correctly during the wash cycle.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Fix a broken or missing detergent dispenser cover that's cracked or won't guide proper detergent placement. Simple 5-minute replacement repair.

This assembly combines the dispenser housing with the water inlet valve, controlling the flow of water into the washer's detergent and softener dispensers. It mounts at the back of the machine where the water supply hoses connect. Replace this assembly if the washer is not filling properly, water leaks from the back, or detergent is not being dispensed correctly during the wash cycle.

This is the complete detergent dispenser drawer assembly for a front-load or top-load washing machine. It holds and dispenses detergent, fabric softener, and bleach at the appropriate times during the wash cycle. Replace this assembly if the dispenser drawer is cracked, if detergent is not dispensing properly, or if residue builds up and cannot be cleaned out.

Mounting screw for washer cabinet and component assembly. Replace if screw is stripped, missing, or damaged during disassembly. Essential hardware piece.

Metal sheet-metal screw secures panels, brackets, and internal components. Replace when missing, stripped, or damaged to restore proper fit.

Seals hot and cold water connections to your washer's dispenser. Replace if you notice leaking at the inlet assembly. Confirm fit with your model number.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.