Parts for Frigidaire FWT867GHS0: 03 - Control Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This is a small plastic latch that secures the detergent or fabric softener dispenser drawer in the closed position on a front-load washer. It clicks into place to hold the drawer shut during the wash cycle and prevent leaks. Replace this latch if the dispenser drawer won't stay closed, pops open during operation, or the latch tab is cracked or broken.

Suspension spring for washer drum support system. Replaces worn, stretched, or broken springs that cause excessive vibration or drum movement during cycles.

Replace a broken or cracked washer dispenser drawer that won't close properly or is leaking detergent. Includes drawer, handle, and trim components.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

This is a 7-position temperature selector switch that mounts on the washer's control panel and allows you to choose the water temperature for each wash cycle. It controls the mix of hot and cold water entering the tub. Replace this switch if your washer fills with the wrong water temperature, only uses hot or cold regardless of the setting, or if the temperature dial no longer clicks into position.

This is a genuine OEM timer that can be used with different models of washers and has been manufactured by Frigidaire. This part has been sourced directly from the manufacturer to ensure the highest possible quality.This timer is critical for the dryer to run properly as it controls the electrical components to enable the correct duration of the washing machine's cycles. If the timer is broken, the washing machine may not run for the intended amount of time or, in some cases, might not function at all. In such instances, the timer will need to be immediately replaced. The appliance will need to be completely disconnected from all power and water sources before repairs are undergone and work gloves should be worn to prevent injury.This timer is sold individually and is manufactured from high-quality, durable, non-corrosive materials. It is an authentic replacement part and compatible with a variety of models of washing machines that have been made by Frigidaire, Electrolux, Gibson, and Kelvinator.

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

Replacement mounting screw for securing appliance panels, brackets, and internal components. Needed when original fasteners are stripped, missing, or lost.

Rotary control knob that fits onto the control shaft to select settings. Replace if your original knob is cracked, broken, worn, or missing.

This control knob replaces a worn, cracked, or missing range/stove dial so you can select heat and settings with a secure grip and clear position indicator. It restores normal operation of the control shaft. What it does:

• Fits onto the control shaft to turn the burner/oven setting and indicate the selected position.
• Restores a solid grip and visible pointer for precise adjustments.
• Common symptom fix: knob is loose, stripped, cracked, or missing and won't turn or hold a setting.
• Helps avoid accidental setting changes from a damaged or worn knob.

• Disconnect power to the appliance before service to avoid shocks or accidental heating.
• Pull the old knob straight off the control shaft; line up splines and push the new knob onto the shaft until fully seated.
• Do not force or hammer the knob onto the shaft; if it does not seat easily, verify spline alignment.
• If the control stem or switch is damaged, replace the stem/switch assembly rather than forcing a knob.

The timer pointer is the small indicator arrow or needle that attaches to the face of a mechanical timer dial, showing you the current cycle position as the timer advances. It helps you read exactly where in the wash, dry, or cook cycle your appliance is. Replace this pointer if the original has broken off or gone missing, making the timer dial impossible to read accurately.

Secure hose clamp for dishwashers and washers. Replace if worn, loose, or leaking. Verify fit with your model number before ordering.

This is a rubber hose that connects the detergent or fabric softener dispenser to the wash tub, allowing dispensed products to flow into the drum during the wash cycle. Over time this hose can crack, clog, or develop leaks. Replace it if you notice detergent not reaching the tub, water leaking near the dispenser area, or visible deterioration of the hose.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Suspension bushing for washer tub assembly. Replaces worn, cracked, or missing bushings that cause excessive noise or tub movement during cycles.

Secures washer hoses to prevent leaks and water damage. Replace if cracked, rusted, or loose to maintain proper seal. Verify fit with your model number.

Wire harness that connects to the dispenser valve in your washer. Replace if wires are damaged, connectors are broken, or harness is melted or corroded.

Vibration dampener pad that reduces noise and movement during wash cycles. Replaces worn, cracked, or missing dampeners that no longer cushion properly.

Replacement bushing that cushions and centers the washer's top panel. Needed when original is worn, cracked, or missing, causing panel rattles or loose fit.

Vibration dampener pad that reduces noise and movement during wash cycles. Replaces worn, cracked, or missing dampeners that no longer cushion properly.

This washer control board manages all electronic functions including cycle selection, water temperature, and spin speed. The control board processes signals from the user interface and controls various components throughout the wash cycle. Replace this board when your washer won't start, cycles don't advance properly, or buttons don't respond.

Lower spring tub sleeve for washers. Protects and guides the suspension spring connection to the tub. Replace if cracked, worn, or missing.

Upper spring tub sleeve for washers. This bushing cushions the suspension spring connection to the tub. Replace if worn, cracked, or missing.

This washer control board manages all electronic functions including cycle selection, water temperature, and spin speed. The control board processes signals from the user interface and controls various components throughout the wash cycle. Replace this board when your washer won't start, cycles don't advance properly, or buttons don't respond.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.