Parts for Frigidaire NGSTR127AS0: 03 - Control Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Fix a washer door that won't close or latch properly with this door latch handle. Restores secure door closure for laundry centers and combo units.

Suspension spring for washer drum support system. Replaces worn, stretched, or broken springs that cause excessive vibration or drum movement during cycles.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Fix a washer that won't start or spin with this lid switch replacement. Common fix for washers that stop mid-cycle. Standard DIY repair in 30 minutes.

This is a genuine OEM timer that can be used with different models of washers and has been manufactured by Frigidaire. This part has been sourced directly from the manufacturer to ensure the highest possible quality.This timer is critical for the dryer to run properly as it controls the electrical components to enable the correct duration of the washing machine's cycles. If the timer is broken, the washing machine may not run for the intended amount of time or, in some cases, might not function at all. In such instances, the timer will need to be immediately replaced. The appliance will need to be completely disconnected from all power and water sources before repairs are undergone and work gloves should be worn to prevent injury.This timer is sold individually and is manufactured from high-quality, durable, non-corrosive materials. It is an authentic replacement part and compatible with a variety of models of washing machines that have been made by Frigidaire, Electrolux, Gibson, and Kelvinator.

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

Replacement mounting screw for securing appliance panels, brackets, and internal components. Needed when original fasteners are stripped, missing, or lost.

Color: white. Measures about 1-1/2 inches in diameter.

White timer control knob for washers. Installs on the control panel to select wash cycles. Replace if cracked, broken, or won't stay attached to shaft.

Secure hose clamp for dishwashers and washers. Replace if worn, loose, or leaking. Verify fit with your model number before ordering.

This dispenser valve assembly controls water flow to the fridge door dispenser for reliable dispensing and shutoff. It replaces a failed valve to restore proper water delivery and stop unwanted dripping or leaks. What it does

• Opens and closes the water passage when the dispenser actuator is pressed to deliver water to the glass.
• Seals the water line to prevent drips or continuous flow when the dispenser is idle.
• Helps stop intermittent dispensing or no-water issues caused by a faulty valve.
• Works with the door dispenser plumbing—electrical/connectors remain unchanged.

• Disconnect power and shut off the refrigerator water supply before starting.
• Remove the refrigerator door panel or access cover per your model's service instructions to reach the valve.
• Verify electrical connector seating and water line fittings are secure; replace any damaged tubing or seals.
• Test for leaks and proper dispensing after restoring power and water.

Water inlet hose for washers and laundry centers. Connects the water supply to your machine. Replace if cracked, torn, leaking, or damaged.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Suspension bushing for washer tub assembly. Replaces worn, cracked, or missing bushings that cause excessive noise or tub movement during cycles.

Secures washer hoses to prevent leaks and water damage. Replace if cracked, rusted, or loose to maintain proper seal. Verify fit with your model number.

This console support bracket secures the range or oven control panel, keeping the console aligned and stable for reliable button and knob operation. It restores proper panel fit and reduces movement or rattling during use. What it does:

• Provides structural support for the appliance control console or control panel
• Keeps the console aligned so switches, buttons, and knobs operate smoothly
• Helps stop console sagging, looseness, vibration, or rattling during operation
• Prevents stress on wiring and switches by holding the panel in place

• Disconnect power to the appliance before beginning any repairs; for gas ranges, shut off the gas supply.
• Support the console or control panel while removing fasteners to avoid dropping the panel.
• Use the original mounting screws and fasteners; align the bracket before tightening.

Wire harness that connects to the dispenser valve in your washer. Replace if wires are damaged, connectors are broken, or harness is melted or corroded.

This rear interior lamp and bracket assembly secures the refrigerator light at the back of the fresh-food compartment and restores reliable interior illumination for loading and unloading. It replaces a damaged or loose lamp housing to improve visibility. What it does:

• Holds and positions the interior lamp at the rear of the cabinet for proper illumination.
• Replaces cracked or broken lamp brackets that leave the lamp loose or misaligned.
• Helps resolve symptoms such as a hanging or wobbly lamp housing and reduced or intermittent rear lighting.
• Works with the existing lamp socket/wiring to provide stable mounting and alignment.

• Disconnect power to the appliance before starting any work to avoid shock.
• Use basic hand tools (screwdriver) to remove the old assembly and secure the new one; keep screws for reuse unless damaged.
• Handle the lamp area carefully to avoid damaging the bulb or wiring; replace the bulb separately if needed.
• Test the light operation after reinstalling and restoring power.

Rubber isolator that cushions vibrating components in your washer. Replace if cracked, worn, or missing to restore proper mounting and reduce noise.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.