Parts for Ge PT958DR1BB: 01 - Control Panel Parts

This offset bracket secures and repositions appliance components to restore proper alignment and support. It replaces a worn or damaged mounting bracket to stop movement and help eliminate noise or misalignment issues. What it does:

• Provides a stable mounting point for panels or assemblies that need offset positioning
• Restores proper alignment when a bracket is bent, cracked, or missing
• Helps stop rattling, vibration, or sagging caused by a loose support
• Works as a direct-fit replacement for the OEM offset bracket

• Disconnect power to the appliance before starting any repair
• Access may require removing exterior panels or trim; keep fasteners organized
• Use the existing mounting hardware unless replacements are specified

Oven won't heat or turn on? This electronic control board restores timed baking, broiling, and temperature regulation. Moderate DIY repair in 1-2 hours.

The Fan Kit is an OEM part for GE ovens and ranges. This part regulates the internal temperatures and preventing overheating.

Causes of a bad Fan Kit can stem from motor failure due to wear and tear, obstructions or debris blocking proper airfl

Fix an oven that won't heat, displays error codes, or has a non-responsive touchpad with this electronic control board. Moderate repair difficulty.

Small adhesive MG logo emblem for appliance exterior. Restores original appearance when factory badge is worn, faded, missing, or damaged. Easy peel-and-stick.

Oven won't heat or overheats? This thermal limit switch protects against temperature extremes. Moderate DIY repair restores safe oven operation.

Oven won't heat or shuts off during baking? A faulty thermal fuse cuts power when detecting excessive heat. This safety device protects your range.

Secures oven insulation behind the cooktop or control panel. Replace this retainer clip if broken, missing, or no longer holding insulation in place.

Inner vent trim piece for wall ovens. Installs around the interior ventilation area to provide a finished look. Replace if cracked, discolored, or missing.

This oven exhaust duct channels hot air and cooking fumes out of the oven cavity to the range venting system, helping maintain proper oven temperature and reduce smoke or odors. Replace a damaged or corroded duct to restore correct venting. What it does:

• Directs hot air and combustion/steam fumes from the oven cavity into the vent ductwork
• Helps maintain consistent oven temperature by providing a clear exhaust path
• Can reduce smoke, burning smells, or poor broil performance when functioning properly
• Prevents loose metal or debris from obstructing the vent path

• One oven exhaust duct

• Disconnect power to the range (and gas supply if applicable) before beginning work
• Access typically requires removing the oven back panel or range back; keep fasteners for reinstallation
• Watch for sharp sheet-metal edges and wear gloves and eye protection
• Reinstall panels and secure all fasteners; test oven operation and venting after replacement

Replacement mounting screw for refrigerators. Secures brackets, panels, handles, and covers. Replace lost, stripped, or damaged screws to restore stability.

Replacement mounting screw secures panels, brackets, and controls on ranges and ovens. Needed when original screws are missing, stripped, or damaged.

6-20 x 3/8 inch nickel screw secures trim panels, brackets, and small components in dishwashers and ovens. Replace missing or stripped screws.

Mounting screw secures range components and panels. Replace if screw is stripped, missing, or damaged during appliance repair or maintenance work.

Black. 8-18 AB HXW 3/8

Range burner clip secures burner components in place. Replace if bent, broken, or burners wobble. Verify fit with your model number before ordering.

Circuit board standoff for ovens. Mounts between the control board and housing to provide proper spacing. Replace if broken, cracked, or missing.

Lubricant cleaner for range and oven control shafts, burner valves, and rack paddles. Dissolves residue and restores smooth operation when parts feel stiff.

Wire harness connecting the logic board to the display panel in wall ovens. Replace if wires are frayed, connectors are damaged, or harness is broken.

Flat multi-conductor ribbon connector links control assemblies to the main wiring harness. Replace when connector is broken, corroded, or missing.