Parts for Ge JD630DF3WW: Control Panel Parts

Control panel assembly for electric ranges. Houses touchpad interface and display. Replace if cracked, unresponsive, or display is damaged or illegible.

This genuine replacement part is an oven control board. The oven control board is the main circuit board that controls the ovens' essential functions. If the oven isn't heating properly, not turning on, or showing an error code on the digital display, it might be time to replace the control board. Replacing a control board may seem like a difficult task, but it is a relatively simple process. Start by unplugging the range. After that, move the appliance away from the wall to gain access to the back. Remove the upper back panel, and locate the control board. Take note of the orientation of the wires using a phone camera. Then detach the wire harness from the old control board. Remove any individual wires with a pair of needle-nose pliers. Then re-attach the wires to the new control board in the correct terminals. Snap the new control board into place and re-install the upper back panel of the range.This OEM replacement part is compatible with General Electric, Hotpoint, and RCA brand ovens.

White control panel support assembly for ranges. Replaces cracked, broken, or damaged support brackets that hold the control panel in place.

Can't control burner heat on your range? The infinite heat switch regulates surface element temperature settings. Straightforward DIY repair.

Burner stuck on high or won't adjust temperature? This range infinite switch controls surface element heat levels. Common DIY fix for uneven heating.

Seals your electric range faceplate to prevent moisture, dust, and debris from entering. Replace when worn or damaged to restore a snug fit. Confirm fit.

Range burner won't shut off or heat properly? The infinite switch controls burner temperature. DIY-friendly repair takes about 15-20 minutes.

Seals the console to keep moisture, grease, and debris from reaching electronics. Replace if crushed, torn, or allowing contaminants in. Confirm fit.

Secures the small clear lens in your range's control panel opening. Replace if cracked, broken, or missing to restore a snug fit and proper appearance.

Replace a cracked, stripped, or missing range control knob. This round dial restores manual operation of cooktop or oven temperature settings.

Indicator light for range control panels. Illuminates to show when burners or functions are active. Replace when dim, flickering, or burned out. Verify fit with your model number.

Secures the clear lens on your range's control panel. Replace if cracked, broken, or missing to keep the lens properly seated and prevent shifting or rattling.

Replace a cracked or discolored indicator light lens to restore clear status visibility on your range. This snap-in lens covers the panel light opening. Confirm fit with your model number.

This harness wire connects the cooktop's infinite (infinite-burner) control to the appliance wiring, restoring reliable power and signal routing for burner temperature control. It replaces a damaged or worn harness to help burners respond properly. What it does:

• Routes power and control signals between the infinite burner control and the cooktop wiring
• Replaces frayed, burnt, or disconnected wiring that can cause a burner to fail or behave intermittently
• Helps restore consistent heat response when a control works but the burner does not heat correctly
• Matches OEM wiring configuration for correct fit and function

• Disconnect power to the appliance before starting any repair
• Follow OEM wiring diagrams and keep wire routing and connector orientation the same as the original
• Inspect connectors and adjacent components for damage; replace any additional faulty parts as needed

Wire harness control assembly for ranges. Connects control board to range components. Replace if wires are damaged, connectors broken, or harness missing.

Replacement mounting screw for appliances. Secures components and reduces vibration. Needed when original screws are missing, stripped, or damaged.

6-20 x 3/8 inch nickel screw secures trim panels, brackets, and small components in dishwashers and ovens. Replace missing or stripped screws.

Mounting screw secures panels, trim, and internal components in ranges and ovens. Replace if missing, stripped, or damaged to restore proper fit.

Black hex washer screw for securing range components like door trim, control panels, and internal brackets. Replace missing or stripped screws during repairs.

Range burner clip secures burner components in place. Replace if bent, broken, or burners wobble. Verify fit with your model number before ordering.

Silicon controlled rectifier for cooktop power control. Includes 8-32 mounting screw. Replace if damaged, corroded, or missing to restore proper installation.