Parts for Kenmore 417.43052200 (41743052200, 417 43052200): Control Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This latch secures the detergent or fabric softener dispenser drawer on a front-load washing machine, keeping it firmly closed during the wash cycle. It clicks into place to hold the drawer shut and releases when pressed to allow access to the dispenser compartments. Replace this latch if the dispenser drawer will not stay closed, pops open during a cycle, or if the latch mechanism is cracked or broken.

Suspension spring for washer drum support system. Replaces worn, stretched, or broken springs that cause excessive vibration or drum movement during cycles.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

This is a 7-position temperature selector switch that mounts on the washer's control panel and allows you to choose the water temperature for each wash cycle. It controls the mix of hot and cold water entering the tub. Replace this switch if your washer fills with the wrong water temperature, only uses hot or cold regardless of the setting, or if the temperature dial no longer clicks into position.

6 Hour delay

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

Replacement mounting screw for securing appliance panels, brackets, and internal components. Needed when original fasteners are stripped, missing, or lost.

Replace your washer's timer knob if cracked, broken, or missing. This control knob installs on the timer shaft and allows you to select wash cycles.

Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.

This dispenser valve assembly controls water flow to the fridge door dispenser for reliable dispensing and shutoff. It replaces a failed valve to restore proper water delivery and stop unwanted dripping or leaks. What it does

• Opens and closes the water passage when the dispenser actuator is pressed to deliver water to the glass.
• Seals the water line to prevent drips or continuous flow when the dispenser is idle.
• Helps stop intermittent dispensing or no-water issues caused by a faulty valve.
• Works with the door dispenser plumbing—electrical/connectors remain unchanged.

• Disconnect power and shut off the refrigerator water supply before starting.
• Remove the refrigerator door panel or access cover per your model's service instructions to reach the valve.
• Verify electrical connector seating and water line fittings are secure; replace any damaged tubing or seals.
• Test for leaks and proper dispensing after restoring power and water.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This is a rubber hose that connects the detergent or fabric softener dispenser to the wash tub, allowing dispensed products to flow into the drum during the wash cycle. Over time this hose can crack, clog, or develop leaks. Replace it if you notice detergent not reaching the tub, water leaking near the dispenser area, or visible deterioration of the hose.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Suspension bushing for washer tub assembly. Replaces worn, cracked, or missing bushings that cause excessive noise or tub movement during cycles.

Fix a washer that won't change speeds or has non-responsive speed settings with this rotary selector switch. Direct-fit 3-position switch restores control.

Dryer back panel cover that encloses the rear of your dryer cabinet. Replace this panel if cracked, dented, or missing to restore the appearance.

Wire harness that connects to the dispenser valve in your washer. Replace if wires are damaged, connectors are broken, or harness is melted or corroded.

Rubber isolator that cushions vibrating components in your washer. Replace if cracked, worn, or missing to restore proper mounting and reduce noise.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.