Parts for Kitchenaid KSSC42FKB01: 05 - Control Panel Parts

The Whirlpool EveryDrop Refrigerator Water Filter 5 is an OEM replacement filter for Whirlpool refrigerators. This filter is used in Whirlpool bottom freezer and side-by-side refrigerators which accept Filter 5. 

• Single Port Filter
• Simple turn installation requires no special tools
• For best performance, replace every six months 
• Micron Rating: 0.5
• Filter Media: Coconut Carbon Block 
• Flow Rate: 0.5 GPM 
• Capacity: 300 gallons
• Temp Range: 33 - 100 °F 
• Pressure Range: 30 - 120 psi
• Approximate dimensions: 2.30 x 3.00 x 11.60 Inches
• Meets NSF Standard: 42
• Approved for WQA Gold Seal
• Reduces 16 contaminants, including lead, mercury, asbestos, etc

A replacement support control bracket that secures the appliance control/console to the cabinet, restoring stable button alignment and preventing the control panel from sagging or shifting during use. Durable stamped metal design for reliable mounting. What it does:

• Secures the control console to the appliance cabinet so the control assembly stays properly positioned
• Prevents the control panel or console from sagging, rocking, or coming loose
• Helps maintain proper alignment of switches, knobs, and electronic controls
• Resolves intermittent button contact or usability issues caused by a loose console

• Disconnect power before beginning any service to avoid shock or injury
• Basic hand tools (screwdriver, nut driver) are typically required; keep original fasteners if present
• Align bracket with factory mounting points and tighten hardware securely but avoid overtightening

This sheet-metal screw secures appliance panels, brackets, and components to the cabinet. Replacing a missing or stripped fastener restores a tight, rattle-free fit and helps keep assemblies aligned for reliable operation.

• Fastens sheet-metal parts to the chassis or support brackets
• Replaces stripped, corroded, or lost screws to restore proper hold
• Helps reduce vibration and noise from loose panels
• Maintains alignment of covers, ducts, or trim

• Disconnect power to the appliance; shut off water or gas if applicable.
• Match this screw to the original location and length.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• If the original hole is damaged, repair or replace the mounting point before installing.

The Light Socket Kit is an OEM part for Whirlpool refrigerators. This kit includes the light socket and necessary components to ensure proper installation and functionality. It is designed to hold the refrigerator light bulb securely and provide reliable electrical connections to illuminate the interior of the refrigerator.

Common causes of failure include wear and tear, corrosion from moisture, or damage from handling or bulb replacement.

Symptoms of a bad Light Socket Kit include:

• Refrigerator light not turning on
• Flickering or intermittent lighting
• Visible damage or corrosion on the socket
• Burned or melted areas around the socket

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement light bulb restores clear, reliable illumination so you can see contents and monitor appliance operation. Replace a burned-out, dim, or flickering bulb to bring visibility back to the area it lights. What it does:

• Provides illumination in the appliance's interior or designated lighting location
• Makes it easier to see contents and check status at a glance
• Common symptoms: light won't turn on, intermittent/flickering light, dim or blackened bulb

• 1 light bulb

• Disconnect power before servicing; allow hot surfaces and the old bulb to cool completely
• Remove any lens/cover, then remove the old bulb
• Install the new bulb securely without overtightening; reinstall the lens/cover if present
• Restore power and test operation

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.