Parts for Electrolux EFLW427UIW1: Control Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This electronic control manages the oven's user interface, timers and heating functions to restore normal temperature and timing behavior. Use it when the control board fails to respond or the display and timers act erratically. What it does:

• Regulates oven bake/broil cycles and overall temperature control signals
• Powers and displays the clock, timer and front-panel readouts
• Processes inputs from the touchpad/controls to select cooking modes and start/stop cycles
• Common symptoms: blank or flickering display, unresponsive touchpad, incorrect clock/timer, or oven not heating as expected

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the board by its edges and avoid static discharge; do not touch circuit traces or components
• Match connectors/mounting points to the original control before installation

A replacement mounting bracket that secures appliance components to the cabinet or chassis, restoring stable support and alignment for panels, assemblies, or controls. What it does

• Provides a durable mounting point to hold panels, assemblies, or components in place.
• Stops loose or sagging panels and reduces rattling or vibration noises.
• Restores proper alignment so doors, panels, or control assemblies fit and operate correctly.
• Replaces damaged, bent, or broken brackets that no longer secure parts.

• One mounting bracket

• Disconnect power (and water, if applicable) before installing to avoid shock or injury.
• Installation typically requires basic hand tools (screwdriver, nut driver); keep hardware and orientation noted for reassembly.
• Do not over-tighten fasteners; align bracket and component before final torque.
• If the bracket mounts to structural studs or inserts, replace any stripped hardware.

The Pressure Sensor Switch is an OEM part for Frigidaire washing machines. It is a component located near the pulsator that monitors water pressure within the washer tub during active cycles. The pressure sensor switch detects water pressure levels and transmits that input to the control board so it can regulate operation accordingly.

Causes for failure of the pressure sensor switch tend to be wear over time, accumulation of minerals/debris that impede functionality, or damage from unexpected water pressure rises. As a safety mechanism, this switch helps prevent overflow or other water-related issues by monitoring pressure inside the tub.

Symptoms of a bad pressure sensor switch include:

• Inability to advance to specific cycles like agitation or spin
• Error codes indicating pressure issues
• Cycles not completing properly or automatically stopping prematurely

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This main control board is the refrigerator's electronic control that manages temperature, fans, compressor, lights and user interface so the appliance operates correctly. Replacing a faulty control board can restore proper cycle and display behavior. What it does

• Controls compressor, evaporator fan, condenser fan and defrost cycle logic
• Manages front panel display and user input signals
• Coordinates temperature sensing and mode settings
• Prevents erratic operation when the original board fails

• Disconnect power to the appliance before beginning work
• Handle the board carefully; avoid static discharge and don't bend the PCB
• Transfer any mounting brackets or harnesses exactly as removed and secure all connectors
• Verify proper operation after reconnection; restore power and run a quick functional check

This control panel is the front console that holds the range's control interface and buttons, restoring a clean, stable surface for operating oven and cooktop functions. It replaces a cracked, warped, or visibly damaged outer panel. What it does:

• Provides the mounting surface and button openings for the range control assembly
• Restores proper alignment and appearance of the control area after impact or wear
• Can resolve issues caused by broken or missing buttons and damaged panel surfaces
• Helps protect the underlying control board from spills and debris

• Disconnect power to the appliance before starting any repair
• Remove oven door/trim per service instructions if required to access the panel
• Handle carefully to avoid scraping painted surfaces or cutting on edges

This replacement door pull restores a secure grip for opening and closing the appliance door and improves the unit's appearance. Designed to match the original part's fit and function for compatible Frigidaire models. What it does:

• Replaces a cracked, broken, loose, or missing door handle so the door can be opened and closed safely.
• Provides a solid grip to prevent slips and accidental drops when handling the door.
• Restores the original look of the appliance for a cleaner, finished appearance.
• Helps prevent further cabinet or trim damage caused by using improper substitutes.

• For your safety, disconnect power (or unplug) before starting work on electric appliances.
• Installation typically requires removing trim or lifting the door slightly—use appropriate hand tools and avoid over-tightening fasteners.
• Keep original fasteners; check the part for included hardware before discarding old screws or clips.

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

A replacement mounting screw used to secure components and panels in compatible appliances. Restores proper fit and prevents loose parts that can cause noise or improper alignment. What it does

• Fastens panels, brackets or small components to the appliance chassis
• Replaces missing or stripped screws that allow parts to shift or rattle
• Helps restore secure fit to reduce vibration and noise
• Maintains correct alignment of mounted components

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or bit to avoid stripping the head
• Install by hand first, then snug; do not over-tighten to prevent damage
• If threads are damaged, replace with the exact OEM screw to ensure proper fit

This clamp secures a hose to its fitting, maintaining a tight, leak-resistant seal at the connection. Replace a fatigued or missing clamp to help prevent drips and stop hoses from working loose under vibration.

• Holds a hose firmly on a pump, tub, dispenser, or valve outlet
• Maintains clamping force to help minimize leaks at the joint
• Helps keep hoses from slipping off during operation
• Common signs: water at a hose joint, loose/slipping hose, damaged or corroded clamp

• Disconnect power and shut off water supply before servicing
• Place a towel or pan to catch residual water at the connection
• Note hose position; remove the old clamp, seat hose fully on the fitting, position the new clamp over the bead, and secure
• After reassembly, run a short cycle and check for leaks

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This cable tie secures wiring and small hoses to appliance frames and harnesses, keeping components organized and reducing wear from rubbing or vibration. It helps maintain safe routing so wires stay clear of moving or hot parts. What it does:

• Fastens wire bundles, harnesses, and small hoses to prevent movement
• Keeps wiring routed away from sharp edges and heat sources
• Reduces noise and wear caused by loose or vibrating wires
• Helps prevent chafing that can lead to insulation damage or intermittent connections

• Disconnect power before servicing electrical components
• Position ties to secure harnesses without over-tightening; trim excess tail
• Keep ties away from high-heat surfaces and moving parts
• Replace any damaged or brittle ties rather than reusing

This is a dispenser inlet gasket intended for use on washing machines. This part ensures that the hot and cold water lines do not leak at the point where they are connected to the appliance. If the washing machine is leaking, the gasket may need to be replaced.Replacing a dispenser inlet gasket in a washing machine can be done easily. Screwdrivers and pliers are required. Disconnect the appliance before starting the repair. Wear work gloves for safety. The hot and cold water lines should both be turned off and removed to prevent flooding.This dispenser inlet gasket is an authentic OEM replacement part. It is sourced from the manufacturer. The replacement component is made of high-quality materials. It can be installed in several different models of washing machines. The dispenser inlet gasket is compatible with appliances produced by Frigidaire, Gibson, Electrolux, Westinghouse, and Kelvinator brands.

Restore proper flow control with this replacement valve assembly. It opens and closes as commanded by the appliance's controls to route fluid to the correct circuit, helping resolve no-flow, slow flow, and leak issues.

• Regulates on/off flow to the designated system/component when signaled
• Directs fluid to the intended circuit for proper fill/dispense operation
• Common symptoms of a failing valve include no flow, slow/intermittent supply, won't shut off, or leaks at the valve or fittings
• May produce humming or clicking without actual flow when malfunctioning

• Disconnect power and shut off the supply line before servicing
• Relieve line pressure and place a towel or tray to catch residual fluid
• Note hose/connector positions; transfer any brackets or fittings from the original if required
• Restore supply and check all connections for leaks and proper operation

This replacement hose routes water within your washer. Replacing a cracked, worn, or leaking hose restores a secure, watertight path so the machine can move water properly without puddles or performance issues.

• Transfers water between internal components during wash cycles
• Maintains a sealed flow path to help prevent leaks
• Damage may present as water on the floor, moisture under the unit, or related fill/drain errors
• Cracks, swelling, abrasion, or loose connections are common failure signs

• Unplug the washer and turn off water supply; have towels or a pan ready for residual water
• Note hose routing and clamp positions before removal; photos can help
• Transfer or replace clamps as needed; seat connections fully and secure firmly
• Run a test cycle and check all connections for leaks

This clamp secures flexible hoses and small-diameter tubing to fittings, helping prevent leaks and keeping connections tight for reliable appliance operation. Use it where a compact, durable clamp is required for water or drain lines. What it does:

• Holds hoses or tubes firmly to inlet/outlet fittings to reduce leaks
• Prevents hoses from slipping off during normal use or vibration
• Helps maintain proper fluid flow by keeping connections sealed
• Useful for water lines, drain hoses, and small appliance tubing

• One clamp

• Turn off and unplug the appliance and shut off water supply before starting
• Inspect the hose and fitting; replace any damaged hose before installing clamp
• Position clamp over the hose/fitting and tighten evenly for a snug fit without crushing the hose

The Housing is an OEM part for Frigidaire washers. It holds the dispenser cup securely in place and ensures proper functioning of the detergent and fabric softener dispensing system.

This housing is specifically designed to fit within your Frigidaire washer, providing stability and support to the dispenser cup. It helps prevent leaks and ensures that the detergent and fabric softener are dispensed accurately during the wash cycle.

A bad housing can be caused by wear and tear, damage, or improper installation. Signs of a faulty lower housing include leaks, loose dispenser cup, or improper dispensing of detergent or fabric softener.

Symptoms of a bad housing include:

• Leaks or drips from the dispenser
• Loose or wobbly dispenser
• Improper dispensing of detergent 

Replace your defective or damaged housing with this genuine OEM Frigidaire part to restore your washer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This drawer assembly replaces a damaged or missing refrigerator storage drawer to restore usable storage space and keep food organized. It installs in the lower compartment and provides a smooth sliding bin for produce or packaged items. What it does:

• Replaces a cracked, broken, or missing refrigerator drawer so food stays contained and easy to access
• Slides on the cabinet rails to allow smooth opening and closing of the storage compartment
• Helps limit spills and keeps loose items from sliding onto lower shelves
• Restores proper fit and appearance inside the refrigerator

• Disconnect power to the appliance before servicing to avoid injury
• Remove contents and any obstructing shelves or bins before installing the drawer
• Handle glass or clear plastic sections carefully to avoid chips or cracks
• If the drawer does not slide smoothly, inspect or replace associated rails or rollers

The Cup Assembly is an OEM part for Frigidaire washers. It is responsible for dispensing detergent, fabric softener, or bleach into the washing machine during the appropriate cycles. This dispenser cup is responsible for ensuring proper distribution of laundry products for effective cleaning and fabric care. It allows you to easily pour in the desired amount of detergent or additives.

Causes of a bad dispenser cup can include clogging, damage to the cup or its components, or malfunctioning electronic components that control the dispensing process.

Symptoms of a bad dispenser cup include:

• Improper dispensing of detergent 
• Residue or build-up in the dispenser 
• Leaks or drips from the dispenser area
• The dispenser door not opening or closing

Replace your damaged or malfunctioning dispenser cup with this genuine OEM Frigidaire part to restore your washer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.