Parts for Viking Range VGRC60: Control / Rack Assembly Parts

This panel-mounted indicator light signals oven operation. Replace it to restore clear status feedback when the original lamp fails, stays on, flickers, or is damaged.

• Illuminates on the control panel to indicate the oven is heating or in use
• Common replacement signs: light does not turn on, remains lit when oven is off, flickers/intermittent, or physical damage
• Restores visible status confirmation during preheat, bake, or broil
• Indicator only; it does not control oven temperature or heating

• Disconnect power at the breaker before servicing
• Access the rear of the control panel to remove the old indicator
• Note wire locations; transfer the leads to the new light and seat it fully
• Restore power and test operation before reassembly

This panel-mounted indicator light signals oven operation. Replace it to restore clear status feedback when the original lamp fails, stays on, flickers, or is damaged.

• Illuminates on the control panel to indicate the oven is heating or in use
• Common replacement signs: light does not turn on, remains lit when oven is off, flickers/intermittent, or physical damage
• Restores visible status confirmation during preheat, bake, or broil
• Indicator only; it does not control oven temperature or heating

• Disconnect power at the breaker before servicing
• Access the rear of the control panel to remove the old indicator
• Note wire locations; transfer the leads to the new light and seat it fully
• Restore power and test operation before reassembly

This is a thermostat made by Viking and is meant for use with ovens. If the current thermostat is faulty or worn, this part can be used for repair or replacement. Without a working thermostat, the oven heat will not be able to be properly maintained at the temperature set by the user. If the oven is struggling to stay hot enough, or cannot heat up at all, the thermostat should be immediately replaced. Special tools are required to replace this thermostat, and the oven will need to be completely disconnected from all power sources. Work gloves are recommended for protection during any repair or replacement process.This is an authentic OEM replacement part made of high-quality materials. This thermostat can be used with a variety of different models of ovens that have been manufactured by Viking and some other brands. This part is sold individually.

This is a top burner knob that is used on oven ranges that were manufactured prior to 2003. A burner knob is what the user turns to adjust the temperature on the burner. This part is manufactured out of a black plastic material and has white lettering on it.A new top burner knob may be needed if the original is cracked, broken, or damaged in any way. If any of the letters wear off of the knob, the user may wish to replace it. If the back of the knob is stripped out and it just spins without activating the range, then it will need to be replaced.This top burner knob is a genuine Viking part and is an OEM part sourced directly from the manufacturer. It is sold individually. This particular top burner knob is compatible with oven ranges that are manufactured by the Viking brand.

Replacement thermostat control knob in black that restores precise temperature selection and safe operation for compatible Viking ranges and cooktops. Simple, direct replacement for a cracked, loose, or missing control knob. What it does:

• Replaces a worn, cracked, stripped, or missing thermostat/control knob so you can set temperature or heat levels as intended.
• Provides a clear pointer for accurate selection of heat or temperature settings.
• Helps prevent accidental changes from a loose or broken knob.
• Fits onto the control stem to restore normal user control.

• Ensure the appliance is turned off and cool before replacing any control parts; disconnect power for electric ranges or switch gas off for gas models when applicable.
• Remove the old knob by pulling it straight off the control stem; align the new knob opening with the stem and push until fully seated.
• If the knob does not seat easily, inspect the control stem for damage or debris and clean or replace the control if needed.

This toggle switch kit replaces a worn or damaged control toggle to restore reliable on/off control for the affected function. It's a direct-fit replacement designed to match the original switch's form and mounting. What it does

• Replaces a broken, loose, or non-responsive toggle switch that prevents proper control
• Restores reliable electrical contact and user control for the associated function
• Stops intermittent operation, arcing, or loss of control caused by a failed switch
• Useful when the toggle lever is bent, loose, or when internal contacts have failed

• Disconnect power (and gas if applicable) before beginning any service
• Access usually requires removing the control panel or console; keep track of screws and trim
• Verify electrical connections and orientation match the original before final assembly
• If wiring shows heat or corrosion damage, replace wiring

This 1/2" x 1/4" rubber bumper cushions contact points to reduce noise and prevent damage on appliance doors, drawers, and panels. It restores proper cushioning for smoother, quieter operation and helps maintain a snug fit. What it does:

• Absorbs shock where panels or doors meet to reduce rattling and clapping noises
• Prevents metal-to-metal contact that can cause chipping, scratching, or wear
• Helps doors and drawers close more evenly by restoring original spacing
• Commonly used where small, press-fit bumpers have worn, flattened, or fallen off

• One 1/2" x 1/4" rubber bumper

• Press-fit replacement; remove old bumper and press new bumper into the same hole until flush
• No special tools required; use a flat pick or small screwdriver to remove old bumper if needed
• Avoid installing on hot surfaces or near heating elements; let appliance cool before service
• Replace matching bumpers in the same area if others show wear for even performance

The Spark Module Wire is an OEM part for Viking ranges and cooktops. It is responsible for transmitting the electrical signal from the spark module to the burner igniters, enabling the burners to ignite when the control knob is turned on. This wire is crucial for the proper functioning of the ignition system, ensuring that the gas ignites quickly and efficiently.

Over time, the spark module wire can become worn or damaged due to heat exposure, accidental pinching during maintenance, or normal wear and tear. When the wire is compromised, it can lead to issues with the burner ignition process, affecting the overall performance of the appliance.

Symptoms of a bad spark module wire include:

• Burners not igniting or taking longer to ignite
• Intermittent sparking or no sparking at all
• Clicking sound without ignition

This OEM part is specifically designed for Viking appliances, ensuring compatibility and reliable performance.