Parts for Viking Range VGRC60: 48" Left Hand Oven Door After 5 / 1994 Parts

This left-hand 48" door handle replaces a damaged or missing refrigerator/freezer door pull to restore a secure, comfortable grip and smooth door operation. Designed as a direct-fit exterior replacement. What it does:

• Provides a sturdy grab point for opening and closing the LEFT door on 48" units
• Replaces handles that are cracked, bent, loose or missing
• Helps prevent cabinet damage and maintains proper door alignment when used as intended
• Matches the original mounting locations for a clean, factory look

• Disconnect power and remove contents from the door before starting work
• Typical installation requires basic hand tools; retain all original fasteners unless replacement fasteners are supplied
• Align handle to factory holes and secure to specified torque; do not overtighten to avoid cracking

This 1/2" x 1/4" rubber bumper cushions contact points to reduce noise and prevent damage on appliance doors, drawers, and panels. It restores proper cushioning for smoother, quieter operation and helps maintain a snug fit. What it does:

• Absorbs shock where panels or doors meet to reduce rattling and clapping noises
• Prevents metal-to-metal contact that can cause chipping, scratching, or wear
• Helps doors and drawers close more evenly by restoring original spacing
• Commonly used where small, press-fit bumpers have worn, flattened, or fallen off

• One 1/2" x 1/4" rubber bumper

• Press-fit replacement; remove old bumper and press new bumper into the same hole until flush
• No special tools required; use a flat pick or small screwdriver to remove old bumper if needed
• Avoid installing on hot surfaces or near heating elements; let appliance cool before service
• Replace matching bumpers in the same area if others show wear for even performance

Replace a faded, scratched, or missing 6-inch black logo badge on your range or refrigerator front panel to restore the original branded appearance.

70-inch stainless steel flexible gas supply tubing for gas ranges. Connects your range to the gas line. Replace if kinked, cracked, or damaged.

Clicking but not lighting? This spark ignitor wire assembly restores reliable ignition on gas cooktops. Moderate DIY repair in 30-45 minutes.

The Spark Module Wire is an OEM part for Viking ranges and cooktops. It is responsible for transmitting the electrical signal from the spark module to the burner igniters, enabling the burners to ignite when the control knob is turned on. This wire is crucial for the proper functioning of the ignition system, ensuring that the gas ignites quickly and efficiently.

Over time, the spark module wire can become worn or damaged due to heat exposure, accidental pinching during maintenance, or normal wear and tear. When the wire is compromised, it can lead to issues with the burner ignition process, affecting the overall performance of the appliance.

Symptoms of a bad spark module wire include:

• Burners not igniting or taking longer to ignite
• Intermittent sparking or no sparking at all
• Clicking sound without ignition

This OEM part is specifically designed for Viking appliances, ensuring compatibility and reliable performance.

This heat-resistant padding insulates the oven cavity to improve energy efficiency and protect surrounding components from excessive heat. Replace it if you notice heat escaping from the oven exterior, increased cooking times, or if the insulation appears compressed or damaged.

This door glass seal strip replaces the rubber/foam seal that fits between the oven door and its inner glass to help keep heat and odors inside the oven. Restores a tighter door seal for more consistent cooking and reduced heat loss. What it does:

• Seals the gap around the inner door glass to reduce heat escaping from the oven cavity
• Helps prevent smoke and odors from leaking into the kitchen during use
• Cushions and stabilizes the inner glass to reduce rattling or vibration
• Supports oven temperature consistency by improving the door seal

• Disconnect power and allow the oven and door to cool completely before starting
• Removing the oven door or inner glass panel may be required; follow the manufacturer service instructions
• Inspect the seal channel and glass edges for damage or debris before installing the new seal
• Use only manufacturer-recommended fasteners or adhesives; do not overtighten clips or screws