Parts for Viking Range VGRC60: Panel / Oven Assembly Parts

A replacement hinge assembly that secures and guides the appliance door for smooth opening and reliable closure. Restores proper door alignment to reduce sagging, rubbing, and incomplete latching on compatible Viking units. What it does:

• Mounts the door to the cabinet and provides the pivot point for opening and closing.
• Supports door weight to prevent sagging and misalignment over time.
• Helps the door close fully and maintain a proper seal to improve operation.
• Common symptoms this part can fix: door droops, door rubs or binds, uneven closing, or noisy hinge movement.

• Disconnect electrical power (and gas supply where applicable) before beginning any repair.
• Support the door while removing/installing the hinge to prevent dropping or damage; have an assistant if needed.
• Keep all fasteners and small parts; replace damaged hardware with OEM-specified screws if required.
• Follow the OEM service manual or diagram for correct orientation, alignment, and torque.

Replaces broken or worn oven door hinges on your gas range. Installs behind the door seal with two screws per side. Sold individually—order two for complete repair.

This 6" replacement leg restores proper height and stability to compatible ranges and ovens. Heavy-duty metal construction supports appliance weight and helps level units for safe, even cooking. What it does:

• Replaces worn or damaged oven/range leveling legs to restore correct height and stability
• Allows appliance to be leveled to stop rocking or movement on uneven floors
• Helps correct door alignment and seal issues caused by an unlevel unit
• Durable design supports normal appliance weight and everyday use

• Two 6" replacement legs

• Disconnect power and gas (if applicable) before servicing; follow all safety procedures
• Have a second person assist when lifting or tilting the appliance to access legs
• Thread legs in by hand; adjust to level, then snug—do not overtighten or force

Seals the right edge of your gas range oven door to contain heat and steam. Replace if worn, cracked, or causing heat loss for consistent cooking.

Seals oven cavity to retain heat and improve cooking performance. Replace when heat escapes, baking is uneven, or gasket shows cracks. Fits 30" and 36" ovens.

Replace your gas range's bottom pan assembly if the existing pan is cracked, dented, rusted, or missing. Installs at the base to contain spills and debris.

This lower access panel replaces a damaged or missing lower front panel to restore the appliance's appearance and protect components behind the kick/vent area. It provides a finished look and shields wiring and components from debris. What it does:

• Covers and protects the lower front opening of the appliance cabinet
• Restores cosmetic appearance after dents, rust, or missing panel damage
• Helps keep dust, debris and small objects out of the service cavity
• Supports proper airflow routing around lower components when installed correctly

• 1 lower access panel

• Disconnect power to the appliance before beginning any work
• Remove the toe kick or existing panel screws to access the mount points
• Handle edges carefully; wear gloves to avoid cuts from sheet metal
• Use the OEM fasteners and align panel to existing mounting holes for proper fit

Lower accessory pan for gas ranges. Installs beneath the cooktop to catch spills and debris. Replace if cracked, warped, or discolored from heat damage.

This 1/2" x 1/4" rubber bumper cushions contact points to reduce noise and prevent damage on appliance doors, drawers, and panels. It restores proper cushioning for smoother, quieter operation and helps maintain a snug fit. What it does:

• Absorbs shock where panels or doors meet to reduce rattling and clapping noises
• Prevents metal-to-metal contact that can cause chipping, scratching, or wear
• Helps doors and drawers close more evenly by restoring original spacing
• Commonly used where small, press-fit bumpers have worn, flattened, or fallen off

• One 1/2" x 1/4" rubber bumper

• Press-fit replacement; remove old bumper and press new bumper into the same hole until flush
• No special tools required; use a flat pick or small screwdriver to remove old bumper if needed
• Avoid installing on hot surfaces or near heating elements; let appliance cool before service
• Replace matching bumpers in the same area if others show wear for even performance

70-inch stainless steel flexible gas supply tubing for gas ranges. Connects your range to the gas line. Replace if kinked, cracked, or damaged.

Clicking but not lighting? This spark ignitor wire assembly restores reliable ignition on gas cooktops. Moderate DIY repair in 30-45 minutes.

The Spark Module Wire is an OEM part for Viking ranges and cooktops. It is responsible for transmitting the electrical signal from the spark module to the burner igniters, enabling the burners to ignite when the control knob is turned on. This wire is crucial for the proper functioning of the ignition system, ensuring that the gas ignites quickly and efficiently.

Over time, the spark module wire can become worn or damaged due to heat exposure, accidental pinching during maintenance, or normal wear and tear. When the wire is compromised, it can lead to issues with the burner ignition process, affecting the overall performance of the appliance.

Symptoms of a bad spark module wire include:

• Burners not igniting or taking longer to ignite
• Intermittent sparking or no sparking at all
• Clicking sound without ignition

This OEM part is specifically designed for Viking appliances, ensuring compatibility and reliable performance.