Parts for Lg LRG3081ST/01: Controller Parts

The Insulator is an OEM part for LG gas ranges. It is a heat-resistant component that helps isolate and insulate internal gas range components from excessive heat. The insulator plays an important role in heat dissipation and preventing overheating of adjoining parts during cooking cycles. 

Causes of a bad insulator include deterioration of the insulation material due to exposure to high temperatures over time from the gas burners. This can cause warping or cracking of the insulator.

Symptoms of a bad insulator include:

• Reduction in heat retention leading to uneven cooking temperatures  
• Conducting excessive heat to non-heating areas of the oven causing unintended warming of components
• Potential gas or fire hazard if insulation breaks down completely

Replace your insulator if you notice any issues to ensure safe operation. This OEM LG replacement insulator restores insulation performance. It is also compatible with Sears/Kenmore gas range models.

This replacement screw fastens panels and components in your appliance, keeping them secure and aligned. Replace stripped, rusted, or missing hardware to stop rattles and ensure assemblies stay tight through everyday use.

• Secures covers, brackets, and internal assemblies at the specified mounting points
• Helps correct looseness or misalignment after a fastener is lost or stripped
• Can reduce rattling or vibration noises caused by loose fasteners
• Restores proper fit of panels or trim pieces

• Disconnect power to the appliance and shut off water or gas before servicing
• Match length and thread to the original fastener before installation
• Start threads by hand to avoid cross-threading; tighten only until snug to prevent damage
• Reuse any washers, spacers, or threadlocker originally installed at this location

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

This customized washer is a small hardware piece that secures fasteners and helps distribute load where screws or bolts attach to appliance components. It restores proper fit and reduces movement at the connection point. What it does:

• Provides a stable bearing surface for screws or bolts to prevent pull-through and material damage
• Helps keep fasteners tight and reduces vibration-related loosening or rattling
• Maintains correct spacing and alignment of panels or internal parts
• Can help form a seal on fasteners in locations prone to vibration or minor movement

• Disconnect power and water (if applicable) before servicing the appliance
• Retain or replace the associated fastener; small parts can be easily lost—work on a clean surface

This factory-specified fastener secures designated panels and components, restoring a precise fit and helping keep your appliance solid and quiet. Replace a missing, stripped, or rusted original with the correct OEM match for the specified locations.

• Secures brackets, panels, and internal parts where this part number is called out
• Replaces damaged, stripped, corroded, or lost screws
• Helps reduce looseness and vibration that can cause rattling noises
• Exact OEM replacement for positions requiring this specific screw

• Disconnect power and shut off water/gas before servicing
• Match to the removed screw and install only in the locations specified for this part number
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening, especially into plastic
• If multiple screws are involved, start all fasteners before final tightening to ensure alignment

This customized screw secures appliance components where a standard fastener won't fit, helping keep panels, brackets and small assemblies stable. It's a direct-fit replacement when the original specialized screw is missing or damaged. What it does:

• Fastens and holds appliance panels, brackets or small parts in place
• Prevents rattling, loose trim or misaligned components caused by a missing or stripped screw
• Matches the OEM fit and thread pattern for proper engagement and alignment
• Used in locations that require a non-standard or customized fastener

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can strip threads or crack parts
• Keep removed hardware organized so you can reinstall in the original location

The Screw is an OEM component specifically designed for LG ranges. It plays an important mounting and fastening role by securely attaching internal components together.

The screws utilized within the range cabinet ensure sturdy construction and reliable mechanical cohesion. They allow for simple assembly and proper alignment of inner parts. 

Causes of bad screws can include wear and tear over time, or damage from overtightening leading to stripped threads or heads.

Symptoms of bad screws include:

• Loose, detached, or misaligned inner parts  
• Hardware that does not fit or interface as designed
• Unintended noises or movement during the operation

This OEM LG replacement part is also compatible with Sears/Kenmore and some GE ranges utilizing similar fasteners. Replacement ensures the range remains mechanically sound.
 

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads

This tapping screw secures appliance panels, brackets, and trim. Replace a missing or stripped fastener to restore a tight, rattle-free fit and keep components properly aligned.

• Cuts its own threads as it drives (self-tapping) to fasten metal or plastic components securely
• Helps eliminate looseness and vibration noises when an original screw is missing or damaged
• Typical signs you need this part: loose or rattling panels, gaps/misalignment, or covers that won't stay secured
• Direct replacement for the original fastener in the same location

• Disconnect power; turn off water or gas supplies before service
• Start the screw by hand to avoid cross-threading, then tighten with the correct driver
• Align parts fully before tightening and avoid overtightening, especially into plastic
• Reuse any original washers or clips that were installed with the screw

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

Replacement window glass that restores a clear viewing area in the appliance door and helps maintain a clean, sealed surface. Ideal for replacing cracked, chipped, or cloudy glass to improve visibility and safety. What it does:

• Provides a transparent viewing window so you can monitor cycles without opening the door.
• Replaces cracked, chipped, or fogged glass to restore appearance and function.
• Serves as the door's viewing surface and works with the door assembly and trim.
• Inspect surrounding gaskets, trim, and fasteners when replacing the glass to ensure a proper fit.

• Disconnect power (and water, if applicable) before attempting any repair.
• Wear cut-resistant gloves and eye protection when handling or removing glass.
• Door disassembly and removal of trim or retaining clips is commonly required.
• If the glass is shattered, remove broken pieces carefully and dispose of them per local regulations.

This cover assembly replaces a damaged or worn poise cover to protect internal components and restore the appliance's appearance. It provides a secure outer panel that helps keep wiring and mechanisms enclosed and accessible for service. What it does:

• Replaces a cracked, bent, or missing poise cover to restore proper enclosure
• Protects internal wiring and components from debris and accidental contact
• Helps prevent rattles and movement caused by a loose or broken cover
• Restores a clean, finished look to the appliance exterior

• Disconnect power and unplug the appliance before starting any repair
• Remove exterior panels or fasteners as needed to access the old cover; keep screws and hardware organized
• Handle the cover carefully to avoid scratching the finish or damaging clips

This hinge assembly secures and pivots a refrigerator/freezer door, restoring smooth, stable opening and closing. Replaces a worn or damaged hinge to help stop sagging doors and reduce rubbing or uneven gaps. What it does:

• Provides the pivot point that allows the door to open and close smoothly.
• Restores proper door alignment to help maintain an even seal and consistent cooling.
• Reduces door sag, rubbing, and catching caused by worn or bent hinges.
• Helps prevent damage to door trim and cabinet edges from misaligned movement.

• One hinge assembly.

• Disconnect power and empty door shelves before starting; support the door while removing the hinge.
• Use appropriate hand tools; follow manufacturer torque recommendations when tightening.
• Inspect door gasket and strike surfaces during replacement to ensure proper sealing.

Main control board that manages the appliance's electronic controls and user interface. Replacing this board restores communication between buttons, display, sensors, and cycle functions when the original board fails. What it does:

• Acts as the appliance's primary electronic control, sending commands to motors, valves, heaters, and sensors.
• Common symptoms of a failing board: blank or unresponsive display, unresponsive controls, erratic cycles, or control-related error messages.
• Often replaced after control failures caused by power surges, moisture damage, or component failure on the board.
• Matches the OEM function of the original PCB to restore normal electronic operation.

• Always disconnect electrical power (and water supply, if applicable) before beginning any service.
• Handle the PCB by the edges and ground yourself to prevent static damage to electronic components.
• Photograph or label all connector locations and wire harnesses before removal; transfer any required mounting hardware or connectors to the new board.

The PCB Assy Power is an OEM part for LG gas ranges. It regulates and monitors the electrical control systems to safely operate burners, oven functions, and auxiliary components. The power board receives inputs from the control panel and thermocouples to distribute outputs that power components including ignitors, valves, and fans. 

Causes of a bad power board can include liquid damage, failures due to intense heat cycling over time, and issues arising from manufacturing defects.

Symptoms of a bad PCB Assy Power include:

• Burners not igniting or functioning properly
• Oven not heating or baking as expected 
• Faulty or unresponsive control panel 
• Error codes displayed

This genuine LG replacement ensures the range's control and safety systems perform reliably. It is also suitable for ranges by Sears/Kenmore containing LG mechanisms and electrical hardware. Installing this high-quality OEM board protects your investment and restores full functionality.

This supporter is a small mounting bracket that holds internal components in place to keep assemblies aligned and reduce vibration. Replacing a damaged supporter restores proper fit and steadies moving parts for quieter operation. What it does:

• Secures internal assemblies or panels to the appliance frame to prevent shifting
• Maintains alignment so doors, drawers or moving parts track correctly
• Dampens vibration and reduces rattling or knocking noises from loose components
• Prevents wear or damage caused by parts moving out of position

• Disconnect power (and water if applicable) before starting any repair.
• Access may require removing exterior panels or covers; keep fasteners organized.
• Install with the correct screws and hand tools; do not over-tighten to avoid cracking the bracket.
• Inspect neighboring clips, screws and supports while replacing this part; replace any additional damaged hardware.

This factory parts assembly replaces a damaged internal assembly to restore proper operation and component fit. It's a direct-fit replacement used where original internal connections or mounts are worn, broken, or missing. What it does:

• Replaces the original internal assembly that secures and connects related components
• Restores mechanical fit and alignment so panels, doors or controls operate correctly
• Helps resolve symptoms such as loose or rattling parts, misaligned components, or intermittent operation tied to a worn assembly
• Maintains OEM fit where original attachment points or brackets are damaged

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle the assembly carefully to avoid bending tabs or damaging connectors
• Reinstall using the original fasteners and observe OEM alignment; do not force parts into place

The Burner Knob Assembly is an OEM replacement part specific to LG gas ranges and cooktops. It refers to the assembly that includes the control knob and stem that adjusts burner flame levels on the stovetop.

Causes of a bad burner knob assembly can include wear from frequent use that results in hard-to-turn or unstable knobs. Overheating from pans placed directly on the knob could also warp and damage plastic components.

Symptoms of a bad burner knob assembly include:

• Difficulty smoothly adjusting burner flames up and down
• Knobs that do not stay securely in the selected flame setting
• Loose, unstable, or misaligned knobs

This genuine LG replacement part is compatible with specific Sears/Kenmore brand models.

The Burner Knob Assembly is an OEM replacement part specific to LG gas ranges and cooktops. It refers to the assembly that includes the control knob and stem that adjusts burner flame levels on the stovetop.

Causes of a bad burner knob assembly can include wear from frequent use that results in hard-to-turn or unstable knobs. Overheating from pans placed directly on the knob could also warp and damage plastic components.

Symptoms of a bad burner knob assembly include:

• Difficulty smoothly adjusting burner flames up and down
• Knobs that do not stay securely in the selected flame setting
• Loose, unstable, or misaligned knobs

This genuine LG replacement part is compatible with specific Sears/Kenmore brand models.

A circular lug designed to join a stripped wire to a threaded terminal for a secure electrical connection. Helps restore reliable contact at terminals and reduces the chance of intermittent power or arcing at connection points. What it does:

• Provides a strong mechanical and electrical connection between a wire and a screw or bolt terminal.
• Helps prevent loose connections that can cause intermittent operation, sparking, or overheating.
• Commonly used where a ring-style termination is required for safe, stable wiring.
• Works with properly sized wire and fasteners to maintain consistent conductivity.

• Always disconnect power to the appliance before inspecting or replacing electrical parts.
• Use the correct lug size and gauge for the wire and terminal; crimp or solder per manufacturer recommendations.
• Tighten terminal hardware to the appliance manufacturer's specified torque; avoid over-tightening which can damage the lug or terminal.
• If wiring insulation or the terminal is damaged or corroded, replace the affected components rather than reusing them.

This heater cover is the protective housing that surrounds and shields the dryer heater assembly, helping direct airflow and preventing contact with the heating element for safer, more reliable operation. What it does:

• Protects the heating element from debris and accidental contact
• Helps channel hot air through the heater assembly for proper drying performance
• Reduces risk of shorting or arcing by keeping wiring and components separated
• Can help eliminate rattling or vibration caused by a damaged or loose heater housing

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the dryer/back panel or cabinet; keep fasteners organized
• Inspect the heater element and surrounding components for damage while replacing the cover
• If you smell burning or see visible damage, replace damaged parts and test on a dedicated circuit

Replacement refrigerator shelf that restores usable storage space and provides a stable, level surface for food and containers. Ideal for replacing cracked, chipped or missing shelves to help keep the fresh-food compartment organized. What it does:

• Provides a flat support surface for containers, plates and groceries
• Replaces cracked, broken or missing shelves that cause instability or lost storage
• Helps keep items from sliding and allows even airflow through compartments
• Restores organized storage and usable shelf height in the fresh-food section

• Remove food and loose items from the compartment before installing
• Slide the shelf into the existing shelf tracks or support brackets until it seats firmly
• If part is glass, handle with care and wear gloves to avoid cuts
• Inspect shelf rails/supports for damage; replace damaged supports before installing

This switch assembly is the door lock mechanism for select front-load washers. It detects when the door is closed and locks it during operation, allowing the washer to start and run safely without interruptions.

• Monitors door position and signals the control; failure can prevent the cycle from starting or trigger door/lock errors
• Engages the latch to secure the door during wash and spin; a bad lock may stop the cycle mid-wash
• Coordinates door unlock at cycle end; faults can delay or prevent unlocking
• Intermittent operation may cause sporadic starts or pauses

• Disconnect power and turn off water supply before servicing
• Access the lock behind the front panel at the door opening; remove the door boot clamp to reach the mounting screws
• Move wire connectors to the new assembly one at a time to maintain placement
• Reassemble and verify proper locking and unlocking before running a full cycle

This grille assembly replaces a damaged or missing front trim piece to restore your refrigerator's finished look and airflow at the base. Durable plastic construction keeps the lower front panel secure and neat. What it does:

• Covers and protects the refrigerator kick/vent area from dust and debris
• Maintains proper airflow to condenser components (helps reduce rattling from loose trim)
• Restores cosmetic appearance when original grille is cracked, broken, or discolored
• Secures to the cabinet with factory clips or screws to prevent gaps and movement

• Disconnect power to the appliance before beginning work
• Removal and installation typically require removing toe kick or lower access panel and releasing retention clips or fasteners
• Handle plastic trim carefully to avoid breaking tabs; replace any damaged clips

The Grille Assembly is an OEM part for LG gas ranges. This assembly covers the ranges' cooking surface and plays an important safety and functional role.  

Symptoms of a bad grille assembly include:

• Warping or bending of grates inhibiting pan placement  
• Grates unable to withstand normal cooking loads
• Chips, cracks, or holes reduce safety and performance
• Grates difficult to remove or clean after cooking

Causes of failure can include damage from years of heat exposure, damage from heavy pans, or warping due to cleaning techniques.

Replace yours today with this genuine OEM LG assembly to maintain a sturdy, reliable, and safe cooking surface. This replacement grate is compatible with some Samsung and Kenmore Elite brand ranges. The grille ensures properly centered cookware and protection from spills or flare-ups.

The Nozzle is an OEM part for LG ranges. It is a small component located inside the burner box that emits gas to create flame. During operation, the nozzle precisely meters fuel flow to each burner to achieve balanced and consistent heating. 

Symptoms of a faulty nozzle include: 

• Burners that light unevenly or emit an irregular flame pattern
• Inability to adjust burner flames or in some cases, lack of ignition
• Possible safety hazard from gas emissions not mixing or igniting properly

Causes can stem from mineral buildup clogging the narrow opening over time. Damage, such as nicks or corrosion, may also disrupt critical gas flow.

This OEM LG part is also compatible with some Kenmore ranges featuring LG gas cooktop systems. Replacing a worn nozzle restores optimal and safe burner performance.

The Nozzle is an OEM part for LG gas ranges. It is a critical component that functions to release gas fuel from the supply line in a regulated and controlled manner to achieve the desired burner flame. The Nozzle has precision-engineered orifices and materials resistant to corrosion to provide reliable and safe operation over extended use.

Symptoms of a bad nozzle include:

• Burner flames that appear uneven, yellow, or unstable 
• Inability to achieve or maintain desired flame height
• Unpleasant gas smells were detected around the range
• Potential safety hazards if damage severely restricts or leaks fuel

Replacing a faulty nozzle restores the exact fuel-air mixture for clean controlled cooking. This affordable OEM LG part ensures optimal and safe burner performance customers expect from their gas range.

This OEM LG part is also compatible with ranges from Crosley, Jenn-Air, and select Kenmore gas models.

The Nozzle is an OEM part for LG gas ranges. It is a critical component that functions to release gas fuel from the supply line in a regulated and controlled manner to achieve the desired burner flame. The Nozzle has precision-engineered orifices and materials resistant to corrosion to provide reliable and safe operation over extended use.

Symptoms of a bad nozzle include:

• Burner flames that appear uneven, yellow, or unstable 
• Inability to achieve or maintain desired flame height
• Unpleasant gas smells were detected around the range
• Potential safety hazards if damage severely restricts or leaks fuel

Replacing a faulty nozzle restores the exact fuel-air mixture for clean controlled cooking. This affordable OEM LG part ensures optimal and safe burner performance customers expect from their gas range.

This OEM LG part is also compatible with ranges from Crosley, Jenn-Air, and select Kenmore gas models.

This nozzle is the burner orifice that meters gas flow to a single burner, helping your range or cooktop produce a correct, stable flame for consistent heating and cooking performance.

• Controls gas flow to its designated burner for proper flame size and shape
• A clogged, worn, or incorrect nozzle can cause weak or oversized flames, yellow tipping, uneven heating, or noisy flames
• Commonly replaced during LP/Natural gas conversions; each burner requires the exact nozzle specified by the service manual
• Useful to check if burner cleaning doesn't restore normal flame behavior

• Disconnect electrical power and shut off the gas supply before servicing
• Match the nozzle to the exact burner position and gas type; verify markings against the original
• Access under the burner/cooktop; use the correct wrench size and avoid overtightening
• After installation, leak-test all fittings with a soap solution and confirm proper flame characteristics per the manual

This replacement burner surface element restores heating on compatible electric cooktops, letting you resume even, controllable cooking. Designed to match the original part's fit and function for straightforward service. What it does:

• Provides the heating element that transfers heat to cookware for stovetop cooking
• Replaces a cracked, non-heating, or unevenly heating surface element
• Helps stop hot spots or intermittent operation caused by a failed element
• Restores normal cooktop temperature control when paired with a working terminal block and controls

• One burner surface element (single replacement part)

• Disconnect power at the breaker before starting any repair to avoid shock
• Remove the cooktop or lift the element from its housing per your model's service instructions; handle gently to avoid bending terminals

This small, board-mounted tactile push-button switch is used on the control panel. It registers a momentary press so the control board can accept your selection. Replacing a worn switch restores reliable button response and consistent operation.

• Mounts to the user interface board and provides momentary contact when a button is pressed
• Sends a low-voltage signal to the control, enabling cycle or option selection
• Typical failure symptoms: unresponsive or intermittent buttons, needing extra force to register, stuck/always-on input, or unintended beeps/changes
• Helps restore consistent user-interface input when an individual button switch has failed

• Disconnect power to the appliance before servicing; shut off gas/water if applicable
• Access the control panel to reach the user interface board
• This is a board-level repair; note switch orientation. Replacement may require desoldering/soldering per OEM procedure
• Use ESD precautions and avoid overheating PCB pads; test button function before reassembly

This genuine replacement power cord assembly restores electrical power to the appliance by replacing a damaged or worn main power cable. It provides a direct, factory-fit connection for safe, reliable operation. What it does

• Delivers mains power from the wall outlet to the appliance's internal wiring and control systems.
• Replaces frayed, cut, melted or otherwise damaged cords that can cause loss of power or intermittent operation.
• Helps eliminate burning smells, visible damage, or exposed wires that indicate a compromised power connection.
• Restores a secure plug and strain-relief connection to reduce stress on terminal connections.

• One power cord assembly.

• Always disconnect power at the breaker or unplug the appliance before starting any work.
• Verify correct cord routing and secure the strain relief/retainer to prevent pinching or chafing.
• Tighten terminal screws to the manufacturer's specification and ensure proper grounding.

The Thermistor is an OEM replacement part for LG gas ranges. It serves as a highly sensitive temperature sensor mounted inside the oven cavity. 

Symptoms of a bad thermistor include:  

• Inability to select certain cooking modes like bake or convection that involve temperature control
• Fluctuating or inaccurate temperature readouts on oven displays
• Irregular cooking outcomes like hot/cold spots inside the oven
• Repeated error codes regarding temperature sensing issues

Causes can be attributed to prolonged exposures to heat and intermittent combustion byproducts inside the oven. Over a decade of use, these conditions may degrade the thermal and electrical properties of sensor components. 

This genuine LG replacement thermistor installs effortlessly. Installing a new thermistor restores temperature monitoring required for reliable gas oven performance. 

A convection fan assembly that circulates hot air inside the oven cavity to promote even baking and roasting. Replacing a worn or noisy fan helps restore consistent cooking performance and airflow in convection ovens. What it does:

• Circulates heated air for more even temperature distribution and improved browning.
• Restores proper airflow when the existing fan is noisy, loose, or failing to spin.
• Helps resolve uneven baking, hot spots, or longer cook times caused by poor air circulation.
• Works as the rotating airflow component of the oven's convection system.

• Disconnect power to the appliance before beginning any work to avoid shock risk.
• Access typically requires removing the oven interior panel or rear access panel; keep track of fasteners.
• Handle sharp sheet-metal edges and support the fan while disconnecting wiring or mounting hardware.

This insulator is the mica sheet that covers the microwave's waveguide opening. It shields the cavity from food splatter and moisture while allowing microwave energy to pass, helping prevent arcing and protecting internal components.

• Covers the waveguide port to keep grease and debris out
• Helps prevent sparking/arcing inside the cavity
• Restores safe, even microwave operation when the original is burned or stained
• Typical symptoms: visible burn marks or charring on the cover, arcing/sparking during use, unusual noises

• Unplug the appliance before service; high-voltage components can retain charge
• Remove the old cover by releasing mounting screw or tabs; clean residue from the area
• Do not bend or crack the new mica; install with the same orientation
• If trimming is required per service literature, follow the outline of the original cover only

This incandescent oven lamp provides interior illumination so you can safely check food without opening the door. Direct replacement for a burned or dim oven/range light to restore cooking visibility. What it does

• Replaces a burned-out or flickering oven interior light bulb
• Restores clear visibility of the oven cavity for monitoring cooking progress
• Helps avoid opening the oven door unnecessarily, preserving oven temperature
• Fits the original lamp socket and installs in the oven light housing

• Disconnect power to the appliance before replacing the lamp to prevent electric shock
• Allow the oven and old bulb to cool completely before handling
• Use a cloth or gloves when installing the new lamp to avoid transferring oils from skin

This packing gasket seals the refrigerator door to help maintain proper temperature and energy efficiency by keeping cold air in and warm, moist air out. It replaces a worn, torn or misshapen door seal to restore a tight closure. What it does:

• Forms an airtight seal around the door edge to reduce cold air loss and prevent warm air intrusion
• Helps stop frost buildup and excess moisture inside the compartment
• Reduces compressor run time caused by air leaks
• Restores proper door alignment and improves cooling performance when old gasket is deformed

• One door packing gasket

• Unplug the appliance or shut off power before starting work
• Clean the door flange thoroughly and remove any old gasket adhesive or debris before installing
• Start at one end and press the gasket evenly into the channel; ensure full seating around the entire perimeter
• If needed, slightly warm the gasket with low heat (hair dryer) to make it more pliable—avoid overheating or stretching

The Packing Gasket is an OEM part for LG ranges. It provides a critical sealing function around the oven door, preventing heat leaks and ensuring efficient, even cooking performance. This gasket is constructed from heat-resistant materials engineered to maintain their flexible integrity even after prolonged high-temperature use.

Causes of a bad packing gasket can include drying or cracking from heat exposure over time, or damage from accidental impacts to the door seal area. 

Symptoms of a bad packing gasket include: 

• Inefficient or uneven cooking as heat escapes around the door 
• Louder noise or vibration coming from the door seal 
• Visible cracks or gaps in the gasket allow a view into the oven cavity

This OEM LG part is also compatible with electric ranges from Hotpoint, RCA, and select Kenmore models.

The Oven Ignitor is an OEM replacement part for LG ovens. It is a critical component responsible for igniting the gas burners or heating elements within the oven, allowing it to reach and maintain the desired cooking temperatures.

Symptoms of a bad oven ignitor include:

• Failure of the oven to ignite or heat up properly
• Intermittent or delayed ignition issues
• Clicking or sparking noises from the ignitor area

Causes of an oven ignitor failure can range from general wear and tear over time, to electrical or mechanical malfunctions, to obstructions or buildup preventing proper ignition.
 
This OEM LG part is also compatible with Sears/Kenmore models.

Replacement dispenser nozzle that directs water or ice from the refrigerator dispenser, helping reduce drips and restore a consistent flow. Simple, direct part to replace a cracked, worn or damaged dispenser spout and improve dispenser performance. What it does:

• Directs water/ice from the dispenser to the cup to reduce splashing and drips
• Restores proper flow when the existing nozzle is cracked, chipped or blocked
• Helps prevent pooling and keeps the dispenser opening cleaner
• Works as a small but critical part of the dispenser assembly to maintain normal operation

• Disconnect power and turn off the water supply before servicing the dispenser
• Inspect surrounding trim and seals; clean area before installing the new nozzle
• Many nozzles snap into place or secure with a single fastener—refer to the OEM service instructions for the exact method

The Gas Orifice Nozzle is an OEM part for LG gas ranges. The gas orifice nozzle regulates the amount of gas entering the burner assembly. It meters out the proper gas flow needed for combustion.

Causes of a bad gas orifice nozzle include mineral buildup obstructing the small opening over time or impact damage distorting the nozzle. 

Symptoms of a faulty nozzle are:

• Unstable or irregular burner flames  
• Changes in flame coloration
• Smells of gas from the range top 
• Inconsistent or improper heating

This part is also compatible with select Sears/Kenmore ranges.

This governor assembly is the mechanical control that stabilizes and regulates motion within the appliance's drive mechanism. Replacing a worn governor restores smooth, consistent operation and helps prevent erratic movement that can strain connected components. What it does:

• Regulates and limits the speed/rotation of the linked drive for stable, predictable movement
• Helps synchronize gears or shafts so the mechanism operates smoothly
• Common symptoms: intermittent or no movement, jerky/erratic motion, clicking or grinding noises
• Visible wear, cracks, or a loose/broken hub on the original governor

• 1 governor assembly

• Disconnect power before servicing; allow moving parts to come to a complete stop
• Note the original orientation; take photos to aid reassembly
• Transfer any reusable brackets, clips, or spacers from the original if required
• After installation, rotate the mechanism by hand to verify free movement before restoring power

This replacement base restores a solid mounting platform for the assembly it supports, keeping components aligned and secure. Replace a cracked or warped base to eliminate looseness, rattling, or misalignment that can lead to premature wear.

• Supports and secures the associated assembly for proper operation
• Maintains alignment to reduce vibration and noise during use
• Helps protect connected parts by preventing shifting and flexing
• Replace when you see cracks, warping, stripped/broken mounts, or symptoms like rattling, looseness, or poor fit

• Disconnect power; shut off water or gas if applicable
• Wear cut-resistant gloves and handle edges carefully
• Document screw locations/routing; transfer any reusable clips or bushings from the old base
• Start screws by hand and avoid overtightening, especially into plastic bosses

This foot is a small rubber base pad that supports and stabilizes the appliance on the countertop or cabinet surface. Replacing a worn or missing foot helps keep the unit level and reduces vibration and slipping.

• Provides stable, non-slip support on flat surfaces
• Helps keep the appliance level for proper operation
• Replaces missing, cracked, or flattened feet
• Can reduce vibration, rattling, or shifting during use

• Unplug the appliance before servicing
• Turn the unit on its side/back for access to the base
• Pull off the old foot and press the new one firmly into place (some models may use adhesive or a tab fit)
• Verify the unit sits level; replace additional feet as needed

This idler bracket mounts the idler pulley or roller in your appliance's tensioning system, keeping a belt or cable aligned and properly tensioned for consistent operation. A bent or worn bracket can cause noise, slippage, or loss of motion.

• Secures the idler pulley/roller in the correct position
• Maintains proper belt/cable tension and alignment
• Helps reduce squealing or squeaking from friction/misalignment
• Can address belts/cables coming off or intermittent movement in the drive mechanism

• Disconnect power; also shut off gas or water before servicing
• Access the tensioner area and note the belt/cable routing and spring orientation
• Relieve tension, remove the old bracket, and transfer the pulley/roller and any spring or hardware as required
• Reinstall the bracket, ensure smooth free movement, route belt/cable correctly, and test operation

This replacement slider restores smooth, guided movement for the appliance component it mounts to, helping reduce sticking, binding and noise. A simple, low-cost part that returns parts to proper alignment and operation. What it does:

• Guides and supports a moving panel or drawer to ensure even, low-friction travel
• Reduces binding, catching or noisy movement when the original slider is worn or damaged
• Keeps the associated component aligned to prevent uneven wear or mis-tracking
• Helps restore normal operation without replacing larger assemblies

• One replacement slider

• Disconnect power to the appliance before beginning any repair
• Remove the affected panel/drawer per the appliance service instructions to access the slider
• Inspect surrounding tracks or mounting tabs for damage and replace if necessary
• Test movement after installation; if binding persists, re-check alignment

This slider is a replacement glide piece that helps a drawer or sliding compartment move smoothly and stay aligned. Replacing a worn slider restores quiet, consistent travel and prevents wear on the surrounding trim. What it does:

• Guides and supports a drawer or sliding compartment for even movement
• Reduces sticking, scraping, and noisy operation from worn glides
• Keeps the drawer aligned to prevent rubbing or binding against the cabinet
• Helps extend life of associated rails and trim by restoring proper tracking

• One slider glide piece

• Disconnect power to the appliance and remove any contents before servicing
• Remove the drawer or access panel per your appliance instructions to reach the slider
• Inspect mating rail and fasteners; replace any damaged clips or screws for a secure fit

This door handle mounting anchor creates the fixed attachment point on the appliance door or drawer. Replacing a worn or missing anchor restores a solid, wobble-free handle and a consistent feel when opening and closing.

• Provides the secure mounting point that the handle fastens to
• Helps keep the handle aligned and rigid during use
• Replace if the anchor is cracked, stripped, or missing
• Resolve a loose/wobbly handle, a handle that won't tighten, or misalignment after service

• Disconnect power; turn off the water supply
• Protect the door/drawer finish and support the handle during removal
• Remove the handle per your model's instructions and take out the damaged anchor
• Install the new anchor using the existing mounting location/hardware, seat the handle fully, then tighten set screws evenly without overtightening

This parts assembly is a factory-style replacement component that restores the original function and fit of the appliance. Use it to replace a worn or damaged assembly without replacing the entire unit. What it does:

• Replaces the original parts assembly that secures and aligns related components
• Restores proper mechanical connection and reduces vibration or loose fit
• Helps resolve symptoms such as abnormal noises, misalignment, or intermittent operation caused by a damaged assembly
• Matches OEM form and fit to maintain normal appliance performance

• High-level installation: remove power and access panel, detach old assembly, and fasten replacement using original hardware
• Follow appliance-specific disassembly steps from the service manual or OEM instructions
• Use proper tools and avoid force to prevent damage to adjacent components