Parts for Lg LRG3081ST/01: Range Parts

Insulator for electric and gas ranges. Replaces cracked, broken, or missing insulation components. Restores proper heat protection and spacing.

This insulator installs inside your gas range to provide heat protection and structural support. Replace if cracked, broken, or missing for proper assembly.

Fix overheating issues in your gas range with this heat-resistant insulator. Protects internal components from excessive heat during cooking cycles.

Replacement screw secures panels and components in your microwave. Install when original hardware is stripped, rusted, or missing to stop rattles.

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

Replacement washer that secures fasteners and distributes load at connection points in ranges and ovens. Needed when original is missing, worn, or damaged.

Replacement screw for electric and gas ranges. Secures internal components and panels. Needed when original is stripped, missing, or damaged during repair.

Secures panels, brackets, and internal components in your range. Replace this screw if the original is missing, stripped, or rusted for proper fit.

This customized screw secures appliance components where a standard fastener won't fit, helping keep panels, brackets and small assemblies stable. It's a direct-fit replacement when the original specialized screw is missing or damaged. What it does:

• Fastens and holds appliance panels, brackets or small parts in place
• Prevents rattling, loose trim or misaligned components caused by a missing or stripped screw
• Matches the OEM fit and thread pattern for proper engagement and alignment
• Used in locations that require a non-standard or customized fastener

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can strip threads or crack parts
• Keep removed hardware organized so you can reinstall in the original location

The Screw is an OEM component specifically designed for LG ranges. It plays an important mounting and fastening role by securely attaching internal components together.

The screws utilized within the range cabinet ensure sturdy construction and reliable mechanical cohesion. They allow for simple assembly and proper alignment of inner parts. 

Causes of bad screws can include wear and tear over time, or damage from overtightening leading to stripped threads or heads.

Symptoms of bad screws include:

• Loose, detached, or misaligned inner parts  
• Hardware that does not fit or interface as designed
• Unintended noises or movement during the operation

This OEM LG replacement part is also compatible with Sears/Kenmore and some GE ranges utilizing similar fasteners. Replacement ensures the range remains mechanically sound.
 

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads

Secures panels, brackets, and trim on your gas range. Replace this self-tapping fastener if it's missing, stripped, or damaged to restore alignment.

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This decorative trim piece is mounted on the oven door and covers the vent opening that allows hot air and steam to escape during cooking. It helps direct airflow while providing a clean, finished look to the door exterior. Replace this part if it is cracked, warped, discolored, or if the vent slots are blocked or damaged.

Replacement window glass for range oven doors. Restores clear viewing area when original glass is cracked, chipped, cloudy, or shattered. Installs inside door.

Inner door cover panel for gas ranges. Protects internal door components. Replace if cracked, damaged, or missing to restore door appearance and function.

This cover assembly replaces a damaged or worn poise cover to protect internal components and restore the appliance's appearance. It provides a secure outer panel that helps keep wiring and mechanisms enclosed and accessible for service. What it does:

• Replaces a cracked, bent, or missing poise cover to restore proper enclosure
• Protects internal wiring and components from debris and accidental contact
• Helps prevent rattles and movement caused by a loose or broken cover
• Restores a clean, finished look to the appliance exterior

• Disconnect power and unplug the appliance before starting any repair
• Remove exterior panels or fasteners as needed to access the old cover; keep screws and hardware organized
• Handle the cover carefully to avoid scratching the finish or damaging clips

Insulator for gas ranges. Installs to provide heat protection and structural support. Replace if cracked, broken, or missing to restore proper function.

Insulator component for gas ranges. Provides heat protection and electrical isolation. Replace if cracked, damaged, or missing to maintain safety.

Secures and pivots your range oven door for smooth opening and closing. Replace if hinge is bent, broken, or causing door misalignment and gaps.

Bracket that secures the door handle to your range. Replace if cracked, broken, or missing to properly mount and support the handle assembly.

Fix unresponsive buttons, blank display, or cycles that won't start with this range main control board. Restores electronic control and user interface.

The PCB Assy Power is an OEM part for LG gas ranges. It regulates and monitors the electrical control systems to safely operate burners, oven functions, and auxiliary components. The power board receives inputs from the control panel and thermocouples to distribute outputs that power components including ignitors, valves, and fans. 

Causes of a bad power board can include liquid damage, failures due to intense heat cycling over time, and issues arising from manufacturing defects.

Symptoms of a bad PCB Assy Power include:

• Burners not igniting or functioning properly
• Oven not heating or baking as expected 
• Faulty or unresponsive control panel 
• Error codes displayed

This genuine LG replacement ensures the range's control and safety systems perform reliably. It is also suitable for ranges by Sears/Kenmore containing LG mechanisms and electrical hardware. Installing this high-quality OEM board protects your investment and restores full functionality.

This supporter is a small mounting bracket that holds internal components in place to keep assemblies aligned and reduce vibration. Replacing a damaged supporter restores proper fit and steadies moving parts for quieter operation. What it does:

• Secures internal assemblies or panels to the appliance frame to prevent shifting
• Maintains alignment so doors, drawers or moving parts track correctly
• Dampens vibration and reduces rattling or knocking noises from loose components
• Prevents wear or damage caused by parts moving out of position

• Disconnect power (and water if applicable) before starting any repair.
• Access may require removing exterior panels or covers; keep fasteners organized.
• Install with the correct screws and hand tools; do not over-tighten to avoid cracking the bracket.
• Inspect neighboring clips, screws and supports while replacing this part; replace any additional damaged hardware.

Wire harness for gas ranges. Connects electrical components inside your range. Replace if wires are frayed, damaged, or connections are loose or broken.

This is the touchpad and control panel assembly that mounts on the front of the range and allows you to select cooking functions, set temperatures, and operate the oven. It includes the membrane touchpad and the decorative panel overlay. Replace this assembly if the touch controls are unresponsive, certain buttons no longer work, or the panel is cracked or peeling.

This is the control panel assembly that houses the buttons, display, and user interface for operating the range. It connects to the main control board and allows you to set temperatures, cooking modes, and timers. Replace this panel if buttons are unresponsive, the display is damaged, or the panel overlay is peeling or cracked.

Replace cracked, stripped, or worn burner control knobs on your gas range. This knob assembly mounts on the control panel to adjust flame levels.

Replace cracked, stripped, or worn burner control knobs on your gas range. This knob assembly mounts on the control panel to adjust flame levels.

This is a circular wire harness holder that secures and organizes internal wiring within the range. It clips onto the frame or mounting points to keep wires routed properly and away from heat sources. Replace this part if it is broken or missing, which can cause loose wiring or potential contact with hot surfaces.

This is a wire holder clip used inside a microwave to secure and route internal wiring. It keeps wires organized and safely positioned away from heat sources and moving components. Replace this holder if it is broken or missing, which can allow wires to hang loose and potentially contact hot surfaces or interfere with other parts.

This heater cover is the protective housing that surrounds and shields the dryer heater assembly, helping direct airflow and preventing contact with the heating element for safer, more reliable operation. What it does:

• Protects the heating element from debris and accidental contact
• Helps channel hot air through the heater assembly for proper drying performance
• Reduces risk of shorting or arcing by keeping wiring and components separated
• Can help eliminate rattling or vibration caused by a damaged or loose heater housing

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the dryer/back panel or cabinet; keep fasteners organized
• Inspect the heater element and surrounding components for damage while replacing the cover
• If you smell burning or see visible damage, replace damaged parts and test on a dedicated circuit

Rubber bumper grommet for electric and gas ranges. Replaces cracked, worn, or missing grommets that cushion and support range components.

This is a metal oven rack that slides into the guide rails inside your oven cavity to support cookware during baking, broiling, or roasting. It provides a flat, heat-resistant surface at adjustable heights within the oven. Replace this rack if it is warped, rusted, or the rails are bent making it difficult to slide in and out smoothly.

This stainless steel panel forms part of your range's exterior surface, providing durability and appearance for high-wear areas. It replaces a dented, scratched, or discolored panel that affects the appliance's appearance or structural integrity.

This is a spark ignition switch assembly with wiring harness that controls the electric igniters on a gas range cooktop. It sends voltage to the spark modules when a burner knob is turned, initiating the clicking ignition sequence. Replace this part if your burners won't spark when turned on, spark continuously even when knobs are in the off position, or if only some burners ignite properly.

This is a surface burner grate assembly for a gas range or cooktop. It sits over the burner and provides a stable, elevated surface to support pots and pans during cooking. Replace this grate if it is cracked, warped, heavily rusted, or if cookware no longer sits level on the burner.

Grille assembly for gas ranges. Covers the cooking surface and supports grates. Replace if warped, bent, cracked, or broken to restore proper pan placement.

Gas burner orifice nozzle for ranges and cooktops. Installs inside the burner box to meter gas flow. Replace if damaged, missing, or converting fuel type.

Fix weak flames or burners that won't light properly with this gas range burner nozzle. Controls gas flow for optimal flame performance. DIY install.

Fix weak flames or burners that won't light properly with this gas burner nozzle. Controls gas flow for proper flame size. Simple install with basic tools.

Weak or uneven flames on your gas range? This burner orifice nozzle meters gas flow for proper flame size and consistent heating. Easy DIY fix.

This is the orifice holder that sits beneath the surface burner on a gas range, securing the gas orifice in position so fuel is directed properly to the burner head. It ensures a consistent and correctly shaped flame for even cooking. Replace this part if you notice irregular flame patterns, difficulty igniting a burner, or if the orifice is loose or misaligned.

Replace a gas range burner when flames are uneven, won't ignite, or produce yellow flames. Direct swap installation takes 10-15 minutes with basic tools.

Burner not heating or heating unevenly? This surface element restores full heat output on your range. Straightforward DIY fix in under an hour.

Gas burner won't light or won't turn off? This gas range valve controls gas flow to burners. Moderate DIY repair taking 30-45 minutes with basic tools.

Gas range burner not lighting or flame too low? This valve controls gas flow to your burners. Common repair for ignition and heating issues on ranges.

This is a surface burner cap designed for a high-output 17,000 BTU burner on a gas range cooktop. It sits on top of the burner base and distributes the flame evenly in a circular pattern for consistent heating. Replace this cap if it is cracked, warped, discolored, or if the burner flame appears uneven or yellow.

Fix unresponsive control panel buttons with this tactile switch replacement. Restores reliable button response. Simple DIY repair, typically under 5 minutes.

This genuine replacement power cord assembly restores electrical power to the appliance by replacing a damaged or worn main power cable. It provides a direct, factory-fit connection for safe, reliable operation. What it does

• Delivers mains power from the wall outlet to the appliance's internal wiring and control systems.
• Replaces frayed, cut, melted or otherwise damaged cords that can cause loss of power or intermittent operation.
• Helps eliminate burning smells, visible damage, or exposed wires that indicate a compromised power connection.
• Restores a secure plug and strain-relief connection to reduce stress on terminal connections.

• One power cord assembly.

• Always disconnect power at the breaker or unplug the appliance before starting any work.
• Verify correct cord routing and secure the strain relief/retainer to prevent pinching or chafing.
• Tighten terminal screws to the manufacturer's specification and ensure proper grounding.

Wire harness assembly for gas ranges. Connects electrical components inside the range cabinet. Replace if wires are frayed, damaged, or connections are loose.

Wire harness for gas ranges. Connects electrical components for proper power distribution. Replace if wires are frayed, damaged, or connections are loose.

If your oven won't reach the right temperature or shows an F9 error, the temperature sensor may be faulty. Simple DIY repair in under 45 minutes.

Fixes uneven baking and noisy oven operation. This convection fan assembly circulates hot air for consistent cooking. Moderate DIY repair restores airflow.

This insulator is the mica sheet that covers the microwave's waveguide opening. It shields the cavity from food splatter and moisture while allowing microwave energy to pass, helping prevent arcing and protecting internal components.

• Covers the waveguide port to keep grease and debris out
• Helps prevent sparking/arcing inside the cavity
• Restores safe, even microwave operation when the original is burned or stained
• Typical symptoms: visible burn marks or charring on the cover, arcing/sparking during use, unusual noises

• Unplug the appliance before service; high-voltage components can retain charge
• Remove the old cover by releasing mounting screw or tabs; clean residue from the area
• Do not bend or crack the new mica; install with the same orientation
• If trimming is required per service literature, follow the outline of the original cover only

Replace a faulty synchronous motor in your gas range. This AC motor assembly controls valve timing and oven functions. Moderate DIY repair for experienced users.

Replace your burned-out or dim oven light bulb to restore interior visibility while cooking. Direct-fit incandescent lamp for safe food monitoring. Verify fit with your model number.

This is a packing gasket that seals the oven door to the range cabinet, preventing heat from escaping during cooking. It is made of a flexible, heat-resistant material that lines the perimeter of the oven door. Replace this gasket if you notice excessive heat escaping from around the door, uneven cooking temperatures, or if the gasket is visibly worn, torn, or hardened.

The range packing seal creates an airtight barrier around oven doors or other range components to maintain proper cooking temperatures and prevent heat loss. Positioned around door edges or component joints, it needs replacement if heat escapes, cooking becomes uneven, or the seal appears cracked or compressed.

Seals your range oven door to prevent heat loss and maintain even cooking. Replace if worn, cracked, or causing temperature issues. Confirm fit with your model.

The Oven Ignitor is an OEM replacement part for LG ovens. It is a critical component responsible for igniting the gas burners or heating elements within the oven, allowing it to reach and maintain the desired cooking temperatures.

Symptoms of a bad oven ignitor include:

• Failure of the oven to ignite or heat up properly
• Intermittent or delayed ignition issues
• Clicking or sparking noises from the ignitor area

Causes of an oven ignitor failure can range from general wear and tear over time, to electrical or mechanical malfunctions, to obstructions or buildup preventing proper ignition.
 
This OEM LG part is also compatible with Sears/Kenmore models.

Burner nozzle holder for gas ranges. Secures the gas nozzle in place on the burner assembly. Replace if cracked, broken, or missing to restore proper fit.

Secures the gas burner nozzle in your range cooktop. Replace this holder if it's cracked, broken, or no longer holding the nozzle firmly in position.

This is a small brass or metal orifice fitting that controls the flow of natural gas to a burner on your range or oven. It has a precisely sized opening that meters the correct amount of gas for proper flame size and combustion. Replace this orifice if you notice uneven flames, yellow or sooty burner output, or if you are converting your range to use a different gas type.

Fix weak flames or uneven heating with a new gas range burner orifice nozzle. Meters proper gas flow to burners. Common issue: mineral buildup clogs.

Fix a burner that won't light or heat unevenly with this gas range burner assembly. Common repair for weak or inconsistent flames on cooktop surfaces.

Pressure regulator assembly for gas ranges. Mounts to the gas supply line to control fuel pressure. Replace if cracked, leaking, or damaged.

Replaces the bottom panel inside your range oven cavity. Install this base if your current panel is warped, stained, or damaged from spills and cleaners.

This is the front panel for the storage drawer located beneath the oven compartment of a range. It provides the visible stainless steel exterior finish and includes the handle mounting points for opening and closing the drawer. Replace this panel if it is dented, scratched, or if the mounting hardware has broken, causing the drawer front to hang unevenly.

Rubber foot pad that supports and stabilizes your range on the floor. Replace if cracked, broken, worn, or missing to keep your appliance level.

This is a metal anti-tip bracket that secures the range to the floor or wall to prevent it from tipping forward. It is a critical safety device, especially when heavy items are placed on an open oven door. Replace or install this bracket if yours is missing, damaged, or if you are repositioning the range after a move or kitchen remodel.

Replacement slider for range drawers and panels. Restores smooth movement when original is worn, cracked, or broken. Mounts to moving components for alignment.

Replace worn range drawer sliders to restore smooth, quiet operation and proper alignment. Prevents damage to surrounding trim. Confirm fit with your model.

Replace your gas range's damaged or broken storage drawer assembly. Essential when the drawer is cracked, warped, or no longer slides properly.

Wire harness for gas ranges. Connects electrical components inside the unit. Replace if wires are frayed, damaged, or connections are loose or broken.

Mounting anchor for range door handles. Replaces worn, broken, or missing anchors to restore secure handle attachment and eliminate wobbling or loose fit.

This is a liquid propane (LP) conversion kit used to convert a natural gas range to operate on LP gas. The kit includes the necessary orifices, fittings, and instructions to safely adapt the burners and oven for LP fuel. Use this kit when relocating a range to an area that uses LP gas instead of natural gas.