Parts for Lg LSSE3030BD/00: Controller Parts

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This replacement screw secures specified panels or components inside your appliance. Refreshing worn or missing hardware helps restore a tight fit, reduce rattling, and keep assemblies properly aligned for reliable performance.

• Provides secure fastening for brackets, panels, or internal assemblies
• Replaces stripped, rusted, or lost hardware
• Helps reduce vibration and rattling noises
• Symptoms include loose panels, shifting components, or a screw that won't tighten

• Disconnect power and allow any hot surfaces to cool before servicing
• Wear cut-resistant gloves and eye protection
• Match length and thread to the original; replace like-for-like
• Start threads by hand to avoid cross-threading; do not overtighten

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

This factory-specified fastener secures designated panels and components, restoring a precise fit and helping keep your appliance solid and quiet. Replace a missing, stripped, or rusted original with the correct OEM match for the specified locations.

• Secures brackets, panels, and internal parts where this part number is called out
• Replaces damaged, stripped, corroded, or lost screws
• Helps reduce looseness and vibration that can cause rattling noises
• Exact OEM replacement for positions requiring this specific screw

• Disconnect power and shut off water/gas before servicing
• Match to the removed screw and install only in the locations specified for this part number
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening, especially into plastic
• If multiple screws are involved, start all fasteners before final tightening to ensure alignment

This customized screw secures appliance components where a standard fastener won't fit, helping keep panels, brackets and small assemblies stable. It's a direct-fit replacement when the original specialized screw is missing or damaged. What it does:

• Fastens and holds appliance panels, brackets or small parts in place
• Prevents rattling, loose trim or misaligned components caused by a missing or stripped screw
• Matches the OEM fit and thread pattern for proper engagement and alignment
• Used in locations that require a non-standard or customized fastener

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can strip threads or crack parts
• Keep removed hardware organized so you can reinstall in the original location

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads

The PCB Assembly, Sidekey is an OEM replacement part for LG  ranges. This printed circuit board assembly is responsible for controlling the functions of the control panel on the side of the range. It communicates with all electronic components to operate the cooktop burners, oven lights and fans, and programming features.   

Causes of a bad PCB assembly can include corrosion of printed circuits over time due to heat exposure, moisture damage, or component failure.

Symptoms of a bad PCB assembly include: 

• Cooktop burners not working properly or unresponsive to control panel commands
• Inability to turn on oven lights or fans
• Programming features like timers or temperatures not functioning correctly
• Blank or unresponsive control panel displays

This OEM LG part is also compatible with Sears/Kenmore ranges. Replace yours today with this genuine electronic control board and upgrade the functionality of your electric range oven.

This control board assembly directs power and communication to key components, interpreting inputs and sensor signals so the appliance runs the correct functions and cycles. Replaces a failed electronics module to restore reliable operation.

• Distributes power and control signals to major components per the unit's programmed logic
• Interfaces with sensors and the user controls to execute selected functions
• Coordinates cycle timing and safety monitoring
• Common signs of failure: no power or won't start, unresponsive controls/display, intermittent operation, error codes, or unexpected shutdowns

• Disconnect power to the appliance before servicing
• Handle the board by the edges; use ESD protection to avoid static damage
• Photograph and label connectors, then transfer them one at a time to the new board
• Secure wiring to avoid pinching; follow the unit's tech sheet or service manual

The Encoder Board is an OEM part for LG ovens. This board is responsible for interpreting the inputs from the control knobs and buttons on the oven's control panel. It sends these signals to the main control board, which then adjusts the oven settings accordingly, such as temperature and cooking mode.

Causes of a bad encoder board can include electrical surges, wear and tear from frequent use, or physical damage to the board's components. A malfunctioning encoder board can disrupt the communication between the user interface and the oven's control system.

Symptoms of a bad encoder board include:

• Unresponsive control knobs or buttons
• Incorrect oven temperature settings
• Oven not starting or turning off unexpectedly
• Error codes displayed on the control panel

This OEM LG part is also compatible with Sears/Kenmore.

The Surface Element is an OEM part for LG electric ranges. It is a glass-ceramic smooth-top cooking surface with embedded heating coils below. Used for easy cleaning and quick heating of pots and pans, the smooth top element must withstand years of daily use. 

Causes of failure include cracks developing in the glass-ceramic material from thermal stress over time. Fatigue of internal heating coils is also possible with heavy usage.

Symptoms of a bad smooth-top surface element include:

• Uneven or slow-heating surface areas  
• Thermal checks, chips, or full cracks appearing in the glass
• Potential electrical hazards if internal coils short dangerously

Replacing this new OEM LG smooth-top element restores a durable, scratch-resistant cooking area that complements modern kitchen designs. It is also compatible with Sears/Kenmore electric range models.

This radiation heater is the element that delivers direct radiant heat for the microwave's grill/browning feature. Replacing a failed heater restores proper grilling performance and helps foods brown and crisp during grill or combination-cook settings. What it does:

• Supplies radiant heat for grill/browning and combo-cook modes
• Typically mounted at the top of the cavity to radiate heat downward
• Common failure symptoms: no heat in grill mode, element does not glow, poor or uneven browning
• Visual clues can include cracks, blistering, or burnt spots on the heater

• 1 radiation heater element

• Disconnect power before servicing; microwaves contain high-voltage components that can retain a charge even when unplugged
• Access may require removing the outer case and interior shroud; beware of sharp metal edges
• Note wire positions before removal; route leads away from hot or moving parts during reassembly
• Verify secure mounts and connections before testing the grill function

This Radiant Surface Element is an OEM replacement part for LG electric ranges and cooktops. It is a high-power coil heating unit located below the cooktop surface that provides efficient, customizable heat for various cooking needs.

Causes of failure can be wear and damage to coiled filaments from prolonged heating cycles, cracking of ceramic insulators, or loose wiring connections suffering arcing or resistance over time.

Symptoms of a faulty element include:

• Slow or inadequate heating of cookware even on high settings
• Temperature fluctuations within the heating zone
• Burning or charring of spills and foods on the element itself
• Tripped circuit breakers obstructing range operation

This replacement is also compatible with some Kenmore models

Power control board assembly that manages the appliance's electronic power distribution and control signals. Replace a failed board to restore consistent electronic control and cycle operation when the control electronics are malfunctioning. What it does:

• Controls power delivery and electronic signals to the appliance's components to enable normal operation.
• Helps resolve symptoms such as the appliance not powering on, controls unresponsive, or cycles failing to start.
• Works as a direct replacement for the appliance's faulty control circuitry.

• Always disconnect the appliance from power before servicing to prevent shock or damage.
• Handle the board by its edges and avoid contact with component leads; observe ESD precautions where possible.
• Installation may require removing panels and unplugging connectors; keep track of screws and wiring positions.

Replace a failed logic board with this main control board. It manages power distribution and system logic so your appliance starts, runs, and cycles correctly when the original board is damaged or unresponsive.

• Supplies and directs power to key components such as motors, fans, heaters, valves, and lights
• Interprets inputs from sensors and the user interface to coordinate proper operation and cycles
• Helps resolve symptoms like no power, won't start, components not running or cycling, frequent clicking from the control area
• A failed board may show scorch marks, a burning odor, or cause intermittent shutdowns and error codes

• Disconnect electrical power before servicing; shut off water supply if your appliance has one
• Use anti-static precautions; handle the PCB by the edges only
• Photograph/label all wiring; move connectors to the new board one at a time to avoid miswiring
• Ensure the board is secured in its housing/bracket, reinstall covers, restore power, and test

The Foot is an OEM part for LG range ovens. It sits at the base of the range and provides stability, as well as protecting countertops from heat and scratches. 

Symptoms of a faulty foot include:

• Wobbling or unstable range that rocks from side to side 
• Visible wear on the bottoms of the feet
• Countertop surface showing signs of heat damage or scratches below the range

Causes can be general wear over years of use, an impact or blow that warped the footing, or adjustment mechanisms becoming loose.

Replacing your LG OEM foot will restore a sturdy, level foundation for safe cooking. The new feet grip securely without slipping to prevent shifting of heavy appliance weight. This will also protect cabinetry surfaces beneath the range. As an official LG part, it is also compatible with some Sears and Kenmore ovens.

This is a replacement outer door frame that restores the door's structure and appearance and helps maintain a proper seal. It's a direct-fit exterior trim piece designed for compatible LG refrigerator doors. What it does:

• Replaces a cracked, bent or damaged outer door frame to restore door alignment and cosmetic finish
• Supports the door outer panel and provides mounting surfaces for handles and trim
• Helps maintain an even door seal by keeping the door edges square
• Stops drafts and reduces moisture entry at the door perimeter when the seal and frame are intact

• Disconnect power to the appliance before starting any repair
• Remove door shelves, handle and any trim pieces as required to access fasteners
• Handle the frame carefully to avoid scratching the finish; use proper fasteners and follow OEM torque guidance

Replacement window glass that restores a clear viewing area in the appliance door and helps maintain a clean, sealed surface. Ideal for replacing cracked, chipped, or cloudy glass to improve visibility and safety. What it does:

• Provides a transparent viewing window so you can monitor cycles without opening the door.
• Replaces cracked, chipped, or fogged glass to restore appearance and function.
• Serves as the door's viewing surface and works with the door assembly and trim.
• Inspect surrounding gaskets, trim, and fasteners when replacing the glass to ensure a proper fit.

• Disconnect power (and water, if applicable) before attempting any repair.
• Wear cut-resistant gloves and eye protection when handling or removing glass.
• Door disassembly and removal of trim or retaining clips is commonly required.
• If the glass is shattered, remove broken pieces carefully and dispose of them per local regulations.

Replacement window glass that restores a clear viewing area in the appliance door and helps maintain a clean, sealed surface. Ideal for replacing cracked, chipped, or cloudy glass to improve visibility and safety. What it does:

• Provides a transparent viewing window so you can monitor cycles without opening the door.
• Replaces cracked, chipped, or fogged glass to restore appearance and function.
• Serves as the door's viewing surface and works with the door assembly and trim.
• Inspect surrounding gaskets, trim, and fasteners when replacing the glass to ensure a proper fit.

• Disconnect power (and water, if applicable) before attempting any repair.
• Wear cut-resistant gloves and eye protection when handling or removing glass.
• Door disassembly and removal of trim or retaining clips is commonly required.
• If the glass is shattered, remove broken pieces carefully and dispose of them per local regulations.

This handle supporter is the bracket that anchors the door handle to the appliance door, keeping the handle secure and aligned. Replacing a cracked or stripped supporter restores a solid, dependable grip on the door.

• Secures the handle to the door and maintains proper alignment
• Helps fix a loose, wobbly, or detached handle
• Replaces a broken or worn mounting bracket that won't hold screws

• Disconnect power and, if applicable, shut off water before service
• Remove the handle and any trim to access the supporter and mounting screws
• Transfer or replace screws as required; do not overtighten into plastic
• Verify handle alignment and operation before fully reassembling

This door hinge assembly supports the refrigerator door and provides a smooth pivot point. Replacing a worn hinge restores alignment and sealing so the door opens and closes properly without sagging, rubbing, or popping.

• Supports the door and serves as the pivot for opening and closing
• Helps keep the door aligned so the gasket seals correctly
• Wear can cause door sagging, rubbing/binding, squeaks/clicks, or poor closing
• Helps with temperature swings or condensation caused by a misaligned door

• Disconnect power; shut off water if the door has dispenser lines
• Support the door before removing hinge fasteners and covers
• Note hinge orientation; transfer/install the new hinge and reuse original hardware as applicable
• Check door alignment and gasket contact; adjust if needed

This main control board replaces the appliance's primary electronic control that manages power delivery and operational commands. Restores control functions so cycles, timers and user inputs respond correctly. What it does:

• Regulates power and sends control signals to motors, valves and sensors
• Handles user commands and cycle sequencing for normal operation
• Can resolve symptoms like no power to controls, unresponsive panel or erratic cycle behavior
• Clears control-related error codes when faulty board is replaced

• One main control board

• Disconnect power before beginning work to avoid shock or damage
• Handle the PCB by its edges and avoid touching components to prevent static damage
• Secure all wiring harnesses firmly during reinstallation
• Test appliance functions after installation; issues may persist

The Lamp Cover is an OEM part for LG ranges. This part is responsible for covering and protecting the indicator light on the range console. It ensures that the indicator light is properly shielded, allowing for clear visibility and easy identification of the selected settings or functions.

A bad lens cover can occur due to damage, discoloration, or wear over time. If you notice symptoms such as a cracked or missing lens cover, diminished visibility of the indicator light, or difficulty in determining the status of the range, it may be time to replace the lens cover.

Symptoms of a bad lens cover include:

• Cracked or missing lens cover
• Diminished visibility of the indicator light
• Difficulty in determining the status of the range

Restore the function and aesthetic appeal of your LG range by replacing the damaged or worn-out lens cover with this genuine OEM part.

This LG replacement part is also compatible with Sears/Kenmore models.
 

The Supporter Rail is an OEM component specifically designed for LG ranges. Located inside the oven cavity, the durable steel rail steadies and spaces baking racks during heating. Its precisely drilled ventilation holes allow air circulation around cookware. 

Symptoms of a bad supporter rail include:

• Rack instability causes pans to shift or bake unevenly
• Permanent stains or burning beneath rack position  
• Warped or misshapen rail inhibiting proper rack fit

Causes involve prolonged exposure to maximum oven temperatures deforming metal over time. Residual spills may corrode protective seasoning.

This authentic LG part restores reliable rack guidance and optimized air circulation for mess-free cooking. Customized for maximized usable space, it facilitates multiple rack baking with confidence. Replace to enjoy stable performance satisfying brand quality and safety expectations for years of cooking enjoyment.

This OEM LG rail also fits select Kenmore and Frigidaire ranges.

This single wiring harness routes electrical power and signals between components to restore proper connections and reliable operation. It replaces a damaged or worn harness to help eliminate intermittent power or control issues. What it does:

• Transfers power and control signals between appliance components to maintain proper function
• Replaces frayed, burnt, or damaged wiring that can cause intermittent operation or component failure
• Helps resolve symptoms like loss of power to a module, erratic behavior, or failure to respond
• Provides a direct plug-and-play connection when matching the correct factory harness

• Disconnect all power (unplug or switch off circuit breaker) before starting any work
• Handle connectors gently and seat firmly until they click into place

This is a single wiring harness that routes power and signals between appliance components to restore reliable electrical connections. It replaces a damaged or worn harness so controls and features can communicate properly. What it does:

• Carries power and control signals between specific components
• Restores interrupted circuits that can cause intermittent operation or component failures
• Helps resolve symptoms like no power to a component, inconsistent function, or error codes tied to open/shorted wiring
• Provides factory-style connectors for a direct fit and reliable connections

• Disconnect power (unplug or turn off breaker) before installing to avoid shock or damage
• Inspect connectors and routing, match connector types and wire colors before connecting
• Avoid pinching or sharply bending wires; secure harness using existing clips or ties

The PCB Supporter is an OEM part for LG ranges and cooktops. It securely mounts and positions the printed circuit board controlling cooking functions.

Causes of a bad PCB Supporter can include cracking or breaking of mounting clips over time due to normal range vibrations and use.  

Symptoms of a bad PCB Supporter include:

• The control board detaching during use
• Intermittent power to heating elements or displays
• Error messages regarding electrical component issues

This OEM LG part is also compatible with some Kenmore models.

This neon indicator lamp provides a visible signal when its circuit is energized, restoring a clear status light on the appliance's panel. Replace a failed lamp to regain quick, at-a-glance confirmation that a function is active.

• Illuminates when power is supplied to the associated circuit, serving as a panel/pilot indicator
• Helps provide clear visual status for appliance functions
• Typical symptoms: indicator does not light, is dim or flickers, stays on continuously, or shows visible damage
• Can fail open or intermittently, leading to unreliable status indication

• Disconnect power to the appliance before servicing
• Access the control/panel area to reach the lamp; note wire routing and terminal orientation
• Transfer leads and seat the lamp securely; handle components carefully to avoid damage
• If the original is board-soldered, board-level repair may be required.

This rotary switch sits behind the control knob and selects your appliance's settings. It directs power to the chosen function so the unit responds when you turn the knob, helping restore reliable, precise control. What it does

• Selects operating modes or speeds as you turn the control knob
• Routes electrical power to the correct circuit for the chosen setting
• Common failure signs: no response, only one setting works, intermittent operation, or the knob turns without detents/feels loose

• 1 rotary switch

• Disconnect power before servicing; allow any hot components to cool
• Photograph or tag each wire on the old switch; move wires one at a time to matching terminals
• Reuse mounting hardware as needed and align the shaft with the knob's flat
• Inspect connectors for heat damage; replace any compromised terminals to ensure a secure fit

This rotary switch mounts behind the control knob and reads your selections on the user interface. Replacing a worn switch restores accurate, reliable knob response so the appliance recognizes the chosen setting and relays it to the control board.

• Detects the position of the selector knob and sends the appropriate signals to the main control
• Enables choosing programs/settings using the front knob
• Failure may cause unresponsive or erratic selection, settings not changing when the knob turns, or a no-start if no selection is registered
• Typically located on the back of the control panel behind the knob

• Disconnect power before servicing
• Remove the knob and access the control panel to reach the switch
• Release locking tabs or screws; transfer the wire connector in the same orientation
• Align the shaft correctly with the knob and test operation before reassembly

The Spring is an OEM replacement part for LG ranges. Located within the oven door mechanism, this coiled metal spring helps counterbalance the weight of the door for smooth opening and closing. 

Causes of a bad spring can include fatigue from repeated compression cycles over several years, as well as stretching or damage from forced closure of an overloaded door. 

Symptoms of a bad spring include:

• Difficulty lifting or closing the oven door
• Sagging or misaligned door that doesn't stay shut  
• Loud squeaking or rubbing noises during use
• Broken, loose, or stretched coils losing tension  

This OEM LG part is also compatible with Sears Kenmore ranges and select GE models.

A circular lug designed to join a stripped wire to a threaded terminal for a secure electrical connection. Helps restore reliable contact at terminals and reduces the chance of intermittent power or arcing at connection points. What it does:

• Provides a strong mechanical and electrical connection between a wire and a screw or bolt terminal.
• Helps prevent loose connections that can cause intermittent operation, sparking, or overheating.
• Commonly used where a ring-style termination is required for safe, stable wiring.
• Works with properly sized wire and fasteners to maintain consistent conductivity.

• Always disconnect power to the appliance before inspecting or replacing electrical parts.
• Use the correct lug size and gauge for the wire and terminal; crimp or solder per manufacturer recommendations.
• Tighten terminal hardware to the appliance manufacturer's specified torque; avoid over-tightening which can damage the lug or terminal.
• If wiring insulation or the terminal is damaged or corroded, replace the affected components rather than reusing them.

This rear cover replaces the cabinet rear panel to protect internal components and maintain proper airflow. It restores the exterior finish and keeps wiring and mechanical parts shielded from dust and damage. What it does:

• Covers and protects internal components at the appliance rear to prevent accidental contact and debris buildup
• Helps maintain proper airflow routing and component clearance behind the unit
• Restores a finished appearance to the rear of the appliance after repair or part replacement
• Useful when the original rear panel is dented, cracked, or missing

• One rear cover as shown

• Disconnect power (and water if applicable) before starting any repair
• Installation typically requires removing the old rear panel screws and securing this cover with OEM-specified fasteners
• Handle edges carefully and support the cover during installation to avoid scratching or dropping onto internal components

This heater assembly replaces the dryer's built-in heating unit to restore normal drying performance by producing warm air for the drum. It's the core component that heats incoming air before it circulates through the appliance. What it does:

• Generates the warm air needed to dry clothes; a failed unit can cause little or no heat.
• Restores normal drying time when worn or damaged heating elements stop functioning.
• Helps prevent uneven drying caused by partial heating failures.
• Works with the dryer's thermostats and safety devices to regulate temperature.

• Disconnect power to the dryer before beginning any service.
• Access typically requires removing the dryer's back or front panel—follow the model service manual.
• Label or photograph wiring before disconnecting to ensure correct reassembly.
• Test the dryer on a dedicated circuit after installation and verify proper operation.

This heater bracket is a metal mounting support that holds the appliance's heater or heating element securely in place, helping maintain proper alignment and reduce movement. Replacing a bent or broken bracket restores stable support for the heater assembly. What it does:

• Secures the heater or heating element to the appliance frame so the element stays aligned and does not contact other components.
• Prevents rattling, shifting, or sagging of the heater assembly that can cause noise or uneven heating.
• Helps maintain safe clearances between the heater and surrounding parts.
• Used when the original bracket is cracked, bent, or missing hardware.

• Disconnect power (and gas, if applicable) before beginning work to avoid electrical shock or gas hazards.
• Handle metal parts carefully — edges may be sharp. Wear gloves and eye protection.
• Match the part number and orientation, secure all fasteners, and ensure the heater is properly aligned before restoring power.

This glass refrigerator shelf provides a flat, stable surface for storing food and containers, restoring usable shelf space and helping keep items organized. It replaces a broken, cracked or missing shelf to improve storage layout. What it does:

• Provides a sturdy, flat surface for food, beverages and containers
• Restores lost shelf space when a shelf is cracked, chipped or missing
• Helps contain small spills and makes items easier to organize and access
• Fits into existing shelf supports to recreate proper storage levels

• Remove food and shelves above the installation area before starting
• Wear cut-resistant gloves when removing a broken shelf and handling glass
• Align glass with the fridge's shelf supports and slide into place until seated
• If shelf support clips are damaged, replace them before installing the new shelf

This small, board-mounted tactile push-button switch is used on the control panel. It registers a momentary press so the control board can accept your selection. Replacing a worn switch restores reliable button response and consistent operation.

• Mounts to the user interface board and provides momentary contact when a button is pressed
• Sends a low-voltage signal to the control, enabling cycle or option selection
• Typical failure symptoms: unresponsive or intermittent buttons, needing extra force to register, stuck/always-on input, or unintended beeps/changes
• Helps restore consistent user-interface input when an individual button switch has failed

• Disconnect power to the appliance before servicing; shut off gas/water if applicable
• Access the control panel to reach the user interface board
• This is a board-level repair; note switch orientation. Replacement may require desoldering/soldering per OEM procedure
• Use ESD precautions and avoid overheating PCB pads; test button function before reassembly

The Magnetron Thermostat is an OEM part for LG microwaves and built-in ranges. Its primary function is to monitor the temperature and ensure that it remains within a safe operating range. If the temperature exceeds the preset limit, the thermostat will interrupt the power supply to the magnetron, preventing overheating and potential damage.

Causes of a faulty magnetron thermostat can include electrical malfunctions, component failures, or physical damage. These factors can result in issues such as erratic heating, microwave not heating properly, or the appliance shutting off unexpectedly.

Symptoms of a bad magnetron thermostat may include:

• Microwave not heating food evenly or at all
• Inconsistent or weak heating performance
• Microwave shutting off or displaying error codes related to temperature issues

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Thermistor is an OEM replacement part for LG gas ranges. It serves as a highly sensitive temperature sensor mounted inside the oven cavity. 

Symptoms of a bad thermistor include:  

• Inability to select certain cooking modes like bake or convection that involve temperature control
• Fluctuating or inaccurate temperature readouts on oven displays
• Irregular cooking outcomes like hot/cold spots inside the oven
• Repeated error codes regarding temperature sensing issues

Causes can be attributed to prolonged exposures to heat and intermittent combustion byproducts inside the oven. Over a decade of use, these conditions may degrade the thermal and electrical properties of sensor components. 

This genuine LG replacement thermistor installs effortlessly. Installing a new thermistor restores temperature monitoring required for reliable gas oven performance. 

The Motor, AC Fan is an OEM part for LG ovens. This fan motor is responsible for circulating air within the oven cavity, ensuring even heat distribution for consistent cooking and baking results. It helps maintain the oven’s temperature by moving hot air around, which is especially important for convection ovens.

Over time, the fan motor can wear out or become faulty due to continuous use, exposure to high temperatures, or electrical issues. When the fan motor fails, it can lead to uneven cooking and potential overheating of the oven.

Symptoms of a bad oven motor, AC fan include:

• Uneven cooking or baking results
• Unusual noises coming from the oven during operation
• The oven taking longer to preheat
• The fan not spinning or running intermittently
• Error codes related to fan or airflow issues

This OEM LG part is also compatible with Sears/Kenmore models.

The Bracket Assembly is an OEM component specifically designed for LG electric ranges utilizing rear-mount control panels. This integral assembly securely attaches the command console within the unit cabinetry.

Causes of a bad bracket can include loosening or stripped screws no longer maintaining a tight interface, impacts warping the steel base compromising flush mounting, or corrosion where dissimilar metals contact deteriorating securing points.

Symptoms of a bad bracket assembly include: 

• Loose panel unable to be properly reinstalled  
• Scratches or abrasions from rattling components
• Drooping controls suffering misaligned activation zones  
• Detached splash guard failing to fully protect surfaces

Replace yours today with this genuine OEM LG assembly to restore a robust interface. Backed mounting flanges deliver long-term stability and compatibility when replacing Samsung, Frigidaire, or GE electric ranges requiring rear console mounting as well. 

This temperature sensor monitors internal appliance temperature and relays it to the electronic control so cycles run correctly. Replacing a faulty sensor restores accurate temperature feedback, helping the unit reach and maintain the set temperature.

• Detects temperature changes and sends a signal to the control board for proper operation
• Supports accurate heating/cooling and cycle timing based on real-time readings
• Direct replacement when the original reads open/short or out of range
• Common symptoms: incorrect temperatures, unusually long/short cycles, failure to reach set temperature, or sensor-related error codes

• Disconnect power before servicing and allow any hot components to cool
• Access the sensor, noting wire routing and connector orientation before removal
• Transfer any mounting clip/holder from the original if needed; seat the new sensor fully
• Route wiring away from moving or hot parts; restore power and run a test or cycle check

A replacement motor bracket that secures the motor to the appliance chassis for stable operation and reduced vibration. Restores proper motor alignment to help maintain smooth, quieter cycles and protect drivetrain components. What it does:

• Holds the motor firmly in place to prevent movement during operation
• Maintains correct motor-to-transmission/gear alignment for reliable power transfer
• Reduces vibration and rattling that can occur when mounts fail
• Helps prevent premature wear of motor and connected components
• Addresses symptoms such as excessive noise, shaking, or motor misalignment

• Disconnect power to the appliance before servicing; follow lockout/tagout best practices
• Turn off water supply and relieve any residual pressure for washer models before disassembly
• Basic mechanical skills and common hand tools required; bracket removal may require loosening motor fasteners and supports
• Reuse OEM fasteners if undamaged and torque to manufacturer specs; inspect surrounding mounts and hardware for wear

This replacement ring secures or positions a nearby appliance component to restore proper alignment and stable operation. It's a small but important part that helps reduce excess movement and related wear. What it does:

• Holds or locates a mating component to prevent unwanted movement or misalignment
• Helps reduce vibration and knocking noises caused by loose parts
• Restores correct spacing that maintains smooth mechanical operation
• Can prevent accelerated wear on adjacent parts when functioning properly

• Disconnect power (and water supply if applicable) before beginning any repair
• Access location may require removing panels or trim; keep fasteners organized
• Inspect surrounding parts for wear or damage and replace if needed

The Convection Fan Blade is an OEM replacement part for LG ovens. It works by circulating hot air throughout the oven, reducing cold spots and promoting consistent temperatures.

Causes of a malfunctioning Convection Fan Blade can be wear and tear from regular use, the accumulation of debris hindering the blade’s rotation, or mechanical issues impacting the fan motor or blade alignment.

Symptoms of a bad Convection Fan Blade include:

• Uneven cooking or baking, leading to partially cooked food
• Noises emanating from the oven during operation, indicating possible damage or obstruction
• The fan not rotating or moving irregularly, signaling mechanical issues

This OEM LG part is also compatible with Sears/Kenmore oven models.

This Fan Blade is an OEM part for LG microwaves. It is a critical component designed to circulate air within the microwave, aiding in heat dissipation and ensuring even cooking. 

Fan blades in microwaves can suffer from wear, imbalance, or damage due to regular use or accumulation of debris. A malfunctioning fan blade can lead to inadequate ventilation, affecting the microwave's cooking efficiency and potentially causing overheating.

Symptoms of a bad fan blade include:

• Unusual noises during operation, such as rattling or buzzing, indicate a loose or damaged blade.
• The microwave overheating or shutting off prematurely.
• Inconsistent cooking or hot spots in food suggest poor air circulation.
• The fan not starting, or stopping unexpectedly during use.
• Visible signs of damage or wear on the blade.

This OEM LG part is also compatible with some Sears/Kenmore models.
 

This AC synchronous motor assembly drives the appliance's rotating components to restore proper operation and consistent performance. It replaces a failed motor to stop stalling, humming or lack of rotation in affected units. What it does:

• Converts electrical input into smooth, synchronous rotational motion for the appliance's driven component
• Stops symptoms like no spin, intermittent rotation, or a motor that hums without turning
• Restores stable, timed movement where a synchronous motor is required
• Interfaces with the appliance's original mounting and wiring harness for direct replacement

• Disconnect power before beginning any repair to avoid electrical shock
• Verify wiring harness orientation and connector seating before applying power
• Inspect mounting points and shaft coupling for wear and secure per OEM guidelines

This heater bracket secures the dryer oven heater assembly to the cabinet, keeping the heating element stable for reliable operation and preventing rubbing or misalignment. It's a simple replacement that restores proper heater positioning. What it does

• Mounts and supports the heater assembly to keep the element in the correct position
• Prevents the heater from shifting, vibrating, or contacting other components
• Helps avoid intermittent heating caused by a loose or misaligned heater
• Works with the heater housing and mounting hardware to maintain safe clearances

• Disconnect power (unplug appliance or shut off breaker) before starting any repair
• Allow the appliance and heater to fully cool before handling
• Basic hand tools required; retain original screws and hardware
• Inspect surrounding components (wiring, insulation) while replacing; replace any damaged parts

This incandescent oven lamp provides interior illumination so you can safely check food without opening the door. Direct replacement for a burned or dim oven/range light to restore cooking visibility. What it does

• Replaces a burned-out or flickering oven interior light bulb
• Restores clear visibility of the oven cavity for monitoring cooking progress
• Helps avoid opening the oven door unnecessarily, preserving oven temperature
• Fits the original lamp socket and installs in the oven light housing

• Disconnect power to the appliance before replacing the lamp to prevent electric shock
• Allow the oven and old bulb to cool completely before handling
• Use a cloth or gloves when installing the new lamp to avoid transferring oils from skin

This sheath heater is the heating element assembly that warms air inside the dryer to remove moisture from clothes. Replaces a worn or failed heater to restore normal drying performance. What it does:

• Generates heat for the dryer's air flow so loads dry efficiently
• Commonly linked to symptoms such as no heat, cool air from the dryer, or significantly longer dry cycles
• Works with the dryer's blower and thermostat system to maintain drying temperature
• Should be tested alongside thermal fuses and thermostats when diagnosing heating problems

• One sheath heater assembly

• Disconnect all power to the appliance before beginning any repair
• Handle the heater element carefully to avoid bending or damaging the sheath
• Inspect and test associated components (thermal fuses, thermostats, wiring) for faults during replacement

The Heating Element is an OEM part for LG electric ranges. It serves a critical cooking function by using electric current to generate heat energy that cooks food inside the oven cavity. The heating element is constructed from flame-resistant and durable materials precisely designed to withstand high temperatures in a clean efficient manner.  

Causes of a bad heating element can include mineral deposits on coils, cracks from overheating, or general wear over extended use.

Replacing a faulty element restores dependable oven performance. 

Symptoms of a bad element include:

• Inefficient or uneven cooking temperatures
• Longer baking and cooking times 
• Cracking or sagging coils affecting heat output
• Potential safety issues if damage exposes live wires

This element also fits the heating designs used in Jenn-Air and Frigidaire electric ovens.

This hinge bracket secures and supports a refrigerator or freezer door hinge, helping the door stay aligned and operate smoothly. Replaces a worn or damaged bracket to restore proper door fit and movement. What it does:

• Provides a mounting point for the door hinge to keep the door aligned
• Prevents door sagging and uneven gaps that can affect sealing
• Reduces rattling or binding during door open/close
• Helps maintain a consistent door seal to support cooling performance

• Disconnect power (and water supply if applicable) before servicing
• Use correct tools and retain original fasteners; follow OEM torque where specified
• Support the door while removing/installing the bracket to avoid damage or injury

This duct assembly routes exhausted air from the dryer to the external vent, restoring proper airflow and reducing lint buildup for safer, more efficient drying. Designed to replace a damaged or disconnected dryer vent duct. What it does:

• Channels hot, moist air from the dryer drum to the outside vent.
• Helps prevent restricted airflow that can cause long dry times and overheating.
• Reduces lint accumulation in the cabinet and exhaust path.
• Restores proper vent routing after dents, holes, or separation.

• One duct assembly.

• Disconnect power and gas before inspecting or replacing vent parts.
• Remove the dryer from its location carefully to access rear duct connections.
• Check and replace any damaged clamps, gaskets, or foil tape for a secure, airtight fit.

The Oven Door Gasket is an OEM part for LG ranges. This seal creates an insulating barrier between the hot oven interior and the external environment. The gasket ensures proper heat retention for energy efficiency and is responsible for safely containing heat inside during baking and broiling. 

Symptoms of a faulty door gasket include:

• Excessive heat loss from the oven that compromises cooking ability
• Discomfort from direct heat around the outer door surface   
• Physical damage or gaps in the insulation compromising its sealing function

Causes of gasket failure involve normal wear and tear from repetitive door openings as well as damage from oven cleaning chemicals or abrasive scrubbing.

This OEM LG part is also compatible with some Kenmore ranges featuring LG oven systems. Replacing the worn gasket restores safe, efficient oven operation.

This outer door frame secures and finishes the refrigerator/freezer door, restoring proper fit and appearance. Replaces a damaged, cracked, or warped frame to help the door seal and close correctly. What it does:

• Provides the structural trim around the door opening and anchors the door panel
• Restores proper alignment and improves door closure when the frame is warped or broken
• Prevents drafts by supporting the door gasket area
• Helps eliminate rattling or loose front panels caused by a damaged frame

• 1 outer door frame

• Disconnect power to the appliance before starting any repairs
• Remove door trim screws and panels carefully to avoid damaging the door or gasket
• Handle the frame and surrounding trim gently to prevent cracking; some clips may be brittle with age

This front plate is the outer panel that restores the appliance's exterior appearance and provides a finished surface for controls and openings. It replaces damaged, dented, or scratched front panels to improve looks and panel alignment. What it does:

• Replaces a cracked, dented, or warped front panel that affects appearance
• Restores proper fit and alignment of control openings and trim
• Helps protect internal components from light bumps and cosmetics damage
• Returns the appliance to a uniform, factory-style exterior

• One front plate

• High-level swap: remove power, detach surrounding trim or control assembly, replace panel, and reassemble; follow manufacturer disassembly order
• Disconnect power before starting. Wear gloves to avoid sharp edges.
• Use manufacturer screws and retainers. Do not force panels; check alignment before tightening.
• If fastening points or clips are damaged, replace them with OEM-specified hardware.

This front panel is the exterior control-panel trim that restores the appliance's appearance and protects the underlying buttons and electronics from everyday wear. It gives a clean, finished look and helps keep controls sealed from spills and debris. What it does:

• Covers and protects the control area and buttons from dirt, moisture, and bumps
• Restores a damaged, cracked, or faded front surface to improve appearance
• Keeps the control electronics accessible while shielding them from direct contact
• Helps the door/control assembly align and fit properly when installed

• One front panel

• Disconnect power before servicing to avoid shock or injury
• Remove any trim screws or snaps holding the old panel; handle clips gently to avoid breaking
• Align panel tabs and secure with original hardware; do not overtighten screws
• Avoid contact with circuit boards and consider an anti-static precaution

This foot is a small rubber base pad that supports and stabilizes the appliance on the countertop or cabinet surface. Replacing a worn or missing foot helps keep the unit level and reduces vibration and slipping.

• Provides stable, non-slip support on flat surfaces
• Helps keep the appliance level for proper operation
• Replaces missing, cracked, or flattened feet
• Can reduce vibration, rattling, or shifting during use

• Unplug the appliance before servicing
• Turn the unit on its side/back for access to the base
• Pull off the old foot and press the new one firmly into place (some models may use adhesive or a tab fit)
• Verify the unit sits level; replace additional feet as needed

This replacement slider restores smooth, guided movement for the appliance component it mounts to, helping reduce sticking, binding and noise. A simple, low-cost part that returns parts to proper alignment and operation. What it does:

• Guides and supports a moving panel or drawer to ensure even, low-friction travel
• Reduces binding, catching or noisy movement when the original slider is worn or damaged
• Keeps the associated component aligned to prevent uneven wear or mis-tracking
• Helps restore normal operation without replacing larger assemblies

• One replacement slider

• Disconnect power to the appliance before beginning any repair
• Remove the affected panel/drawer per the appliance service instructions to access the slider
• Inspect surrounding tracks or mounting tabs for damage and replace if necessary
• Test movement after installation; if binding persists, re-check alignment

This slider is a replacement glide piece that helps a drawer or sliding compartment move smoothly and stay aligned. Replacing a worn slider restores quiet, consistent travel and prevents wear on the surrounding trim. What it does:

• Guides and supports a drawer or sliding compartment for even movement
• Reduces sticking, scraping, and noisy operation from worn glides
• Keeps the drawer aligned to prevent rubbing or binding against the cabinet
• Helps extend life of associated rails and trim by restoring proper tracking

• One slider glide piece

• Disconnect power to the appliance and remove any contents before servicing
• Remove the drawer or access panel per your appliance instructions to reach the slider
• Inspect mating rail and fasteners; replace any damaged clips or screws for a secure fit

This insulator is a small mounting cushion that reduces vibration and prevents metal-to-metal contact in the appliance. It helps lower operational noise and protects nearby parts from wear caused by movement. What it does:

• Cushions and isolates components to reduce vibration and rattling
• Prevents metal edges from rubbing together and causing wear or noise
• Protects wiring and hoses from chafing where parts meet
• Keeps panels and brackets securely spaced for proper alignment

• Disconnect power before accessing internal panels or mounting points
• Remove only the panels required to reach the original insulator; retain fasteners for reassembly
• Press or slide the insulator into place on the mounting stud or bracket; gentle hand pressure is usually sufficient

This door handle mounting anchor creates the fixed attachment point on the appliance door or drawer. Replacing a worn or missing anchor restores a solid, wobble-free handle and a consistent feel when opening and closing.

• Provides the secure mounting point that the handle fastens to
• Helps keep the handle aligned and rigid during use
• Replace if the anchor is cracked, stripped, or missing
• Resolve a loose/wobbly handle, a handle that won't tighten, or misalignment after service

• Disconnect power; turn off the water supply
• Protect the door/drawer finish and support the handle during removal
• Remove the handle per your model's instructions and take out the damaged anchor
• Install the new anchor using the existing mounting location/hardware, seat the handle fully, then tighten set screws evenly without overtightening

The Decor Guard is an OEM part for LG range ovens. It consists of decorative trim pieces that surround the range for an aesthetically pleasing appearance.

Symptoms of a faulty decor guard include: 

• Cracks, chips, or damage appearing to enameled surfaces
• Loose, missing, or improperly aligned trim pieces 

Causes can include impact damage from cookware, repeated heating, and cooling causing materials to expand and contract, or general wear over extended use.

Replacing your LG OEM decor guard with a new set restores the pristine look and feel of the appliance. Precisely cut elements fit seamlessly to specifications while enhancing the range's overall style. This replacement is also compatible with some Sears and Kenmore models.