Parts for Maytag MAT20CSAGW0: 03 - Controls And Water Inlet Parts

This is the front-facing control panel (console assembly) for a dryer, in white. It houses the buttons, knobs, and display used to select cycles, temperatures, and other dryer settings. Replace this panel if the buttons are unresponsive, the panel is cracked, or if cycle selections no longer register properly.

Rear panel for laundry center units. Covers the back of the appliance cabinet. Replace if cracked, dented, rusted, or missing for complete enclosure.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Fix a washer that won't advance through cycles or gets stuck between wash and rinse. This cycle switch controls your wash sequence. DIY repair.

Fix intermittent operation or control failures with this wire harness assembly. Restores electrical connections between components in your laundry center.

The Valve is an OEM part for Whirlpool clothes washers. It plays a vital role in the water fill and drain functions during wash cycles. 

Causes of a bad valve can include mineral buildup from hard water scaling components over time, worn internals due to abrasives in water/clothes loads, or accidental impact damage.

Symptoms of a bad valve include:

• Slow or incomplete water fill times  
• Delayed or improper draining of water 
• Water leaks at the valve area
• High water usage according to utility bills

This replacement valve is also compatible with select Whirlpool-produced brands like Maytag, KitchenAid, and Kenmore washers as well.

Fixes worn, sticky, or broken control buttons that prevent cycle selection. Simple repair restores reliable operation and clean appearance on your washer.

This replacement mounting bracket secures appliance panels and components to restore proper fit and reduce movement. It's a direct-fit bracket used where the original metal support has cracked, bent, or detached. What it does:

• Provides a stable mounting point to keep panels, consoles or assemblies aligned and secure
• Stops rubbing, rattling or vibration caused by a loose or damaged bracket
• Restores correct spacing so doors and panels close and operate smoothly
• Matches OEM fit to maintain factory alignment and assembly integrity

• Disconnect power (and water if applicable) before starting any repair
• Basic hand tools are typically required; remove surrounding trim or panels for access
• Align bracket before tightening fasteners; do not overtighten to avoid stripping threads

10 - 16 x 1/2

Replace your washer fill hose if you notice leaks, cracks, or water flow issues. This hose connects your water supply to the washer. Confirm fit with your model.

The Coin Slide Interface is an OEM part for Whirlpool commercial washers. It is a component that allows users to insert coins or tokens to activate the machine and initiate the laundry cycle.

Causes of a faulty coin slide interface can include regular wear and tear, damage due to misuse or vandalism, or electrical component failure. These factors can result in issues such as coin rejection, incorrect coin counting, or the inability to start the machine using coins.

Symptoms of a Bad Part:

• Will not start
• Not washing properly
• Timer will not set

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Fix intermittent operation or control failures caused by worn or damaged wiring. This wire harness restores reliable power and signal paths to controls and motors.

Number-8, 18-thread mounting screw secures panels, brackets, and assemblies. Replace missing, stripped, or damaged screws to restore secure fitting.