Parts for Ge GCWP1805D0CC: 01 - Controls & Backsplash Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

The Compression Ring is an OEM part for GE washing machines. This ring is essential for securing the tub within the washing machine, ensuring it remains in place during the wash and spin cycles. It helps maintain the stability and proper function of the washing machine.

You should replace the compression ring if it becomes worn, cracked, or damaged. Causes of a bad compression ring can include frequent use, high-stress loads during wash cycles, or physical damage, which can lead to instability and poor washing performance.

Symptoms of a bad compression ring include:

• Excessive shaking or movement of the washing machine during cycles
• Unusual noises during operation
• The washing machine tub appearing misaligned or loose
• Ineffective washing due to instability

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replaces a worn, cracked, or missing rotary control dial on your washer. Restores clear, tactile control for selecting cycles and settings.

Bisque control knob assembly for washers. Includes push-on clip for switch attachment. Replace cracked, broken, or missing knobs to restore control dial operation.

Secures the timer knob to the shaft for accurate cycle selection. Replace if worn, broken, or lost causing knob to spin freely. Confirm fit with model.

This water level pressure switch monitors the tub's fill level and tells the washer when to stop filling and move to the next step. Replace it to restore accurate water levels and dependable cycle progress.

• Monitors air pressure from the tub to determine the selected water level
• Signals the control to open/close the inlet valves for proper fill
• Allows agitation and spin only after the correct level is reached
• Typical symptoms: overfilling or continuous filling, underfilling/low water level, cycle won't start or advance to wash/spin

What's included: 1 pressure switch Install notes:

• Unplug the washer and turn off the water supply before servicing
• Access the control console; note wire positions or take a photo and transfer connectors one at a time
• Move the pressure hose to the new switch; ensure the hose is clear, undamaged, and fully seated
• Secure the switch, reassemble, and run a fill test to confirm proper shutoff

This replacement control knob in bisque restores smooth, reliable control of your dryer's settings. It attaches to the control shaft so you can choose cycles and options when the original knob is cracked, stripped, or missing.

• Mounts to the D-shaped control/timer shaft to select dryer cycles and settings
• Replaces damaged or missing knob for proper engagement and feel
• Helps resolve knobs that spin freely, won't turn the shaft, feel loose, or fall off
• Refreshes the console with a matching bisque finish

• Disconnect power before servicing
• Pull the old knob straight off; remove any broken insert pieces from the shaft
• Align the flat side of the shaft with the knob insert and press on until fully seated
• Do not force; address that before installing the new knob

The Knob Clip is an OEM part for GE washing machines and dryers. This small but crucial component is designed to secure the control knob to the appliance's control panel.  

Over time, knob clips can wear out or break due to frequent use or accidental damage. When this happens, the control knob may become loose, fall off easily, or fail to engage the control panel properly, making it difficult to set the appliance to the desired cycle or function.

Symptoms of a bad Knob Clip include:

• The control knob is loose or falls off the panel easily.
• Difficulty in adjusting settings due to a loose knob.
• The knob does not stay in place or slips when turned.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Size: 8-18 b.

Fix a washer that won't fill with hot or cold water. This rotary temperature switch controls water temperature settings. Easy 5-minute DIY repair.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Fix a washer that won't advance cycles, spins continuously, or has erratic operation. This timer controls wash, rinse, and spin cycles. 10-minute DIY.

Stainless steel hex washer head screw for securing appliance panels, brackets, and trim. Replace missing, stripped, or corroded fasteners during repair.

Harness to corset & shifter

10-18 hex washer screw for securing panels, trim, brackets, and components in appliances. Replaces lost, stripped, or corroded fasteners.

Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.

Guides water from the inlet valve into the wash tub. Replace if cracked, broken, leaking, or causing uneven water distribution in your top-load washer.

Washer won't fill, leaks after cycles, or has no hot water? The triple water valve controls fill, rinse, and dispenser flow. DIY fix in under 1 hour.

12-pack of inlet hose washers for washers and washer dryer combos. Replace cracked, worn, or missing washers to prevent leaks at water connections.

Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.

Connects the pressure switch to the tub in top-load washers. Replace if cracked, punctured, or brittle to restore proper water level monitoring.

Includes 12 terminals.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.