Parts for Ge GHWN4250D2WW: Controls & Backsplash Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Replacement end cap for washer left-side assembly. Secures cabinet alignment and protects internal components. Needed when original is cracked or missing.

Right-side cabinet end cap for washers. Replaces cracked, broken, or missing trim piece. Restores proper fit and protects internal components.

The Pressure Switch is an OEM replacement part for GE washing machines. It's responsible for monitoring the water level inside the wash tub. By signaling the washing machine to start and stop filling with water, it ensures the appropriate water level is maintained for each specific wash cycle.

Symptoms of a bad Pressure Switch include:

• Overfilling or underfilling of the wash tub
• The machine not advancing to the next cycle stage
• Water spilling out of the washing machine
• Inconsistent water levels affecting wash quality

The typical causes for a malfunctioning Pressure Switch can be a result of mechanical wear over time, a defect in the pressure hose leading to incorrect readings, or electrical failures that affect the switch’s ability to communicate with the rest of the washing machine.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The washer start stop switch button is the physical push button on your washing machine's control panel that signals the machine to begin or pause a cycle. It connects to the underlying switch mechanism that sends an electrical signal to the control system. Replace this part when pressing the button does nothing, the button feels mushy or broken, or the washer will not start or stop responding to that control.

Replace your washer's control knob assembly if cracked, broken, or missing. This component attaches to the control panel for cycle selection and settings.

The Probe Sensor (ATC) is an OEM replacement part for GE washers. It plays a key role in monitoring water levels and temperatures during cycles.

Symptoms of a bad probe sensor include:

• Incorrect or inconsistent fill levels
• Fluctuations in water temperature
• Delays or failures at the start of cycles
• Error codes related to lack of temperature/level readings

Causes can include normal wear over time as the delicate internal components are subjected to constant temperature changes and immersion in water. Mineral deposits or contaminants may also affect performance.

This GE replacement is also compatible with Hotpoint, RCA, and some Kenmore models.

Washer won't start or stops mid-cycle? This main control board restores cycle selection and timing. Common DIY fix, takes about 10-20 minutes to install.

Size: 8-18 b.

Stainless steel hex washer head screw for securing appliance panels, brackets, and trim. Replace missing, stripped, or corroded fasteners during repair.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Plastic housing that secures the drain solenoid to the pump assembly. Replace if cracked, broken, or missing to properly position the solenoid mechanism.

Harness to corset & shifter

External logo emblem badge that restores your washer's factory appearance. Replaces missing, faded, or damaged emblems to keep the cabinet looking finished.

10-18 hex washer screw for securing panels, trim, brackets, and components in appliances. Replaces lost, stripped, or corroded fasteners.

Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.

Fix water leaking from the top of your washer or spraying everywhere. This funnel shower head assembly disperses water evenly. Moderate DIY repair.

Washer only fills with cold water or won't stop dripping? The triple water inlet valve controls hot, cold, and warm water flow. DIY repair in 10-15 minutes.

Connects the pressure switch to the tub in top-load washers. Replace if cracked, punctured, or brittle to restore proper water level monitoring.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.