Parts for Kenmore 253.44352409 (25344352409, 253 44352409): Controls Parts

Refrigerator making loud noises or not cooling? A worn evaporator fan blade often causes these issues. DIY-friendly repair typically takes 30 minutes.

Nylon washer for the evaporator fan motor shaft in refrigerators. Replace if worn, cracked, or missing to ensure proper fan alignment and operation.

Replaces worn or damaged shaft support bushing in your refrigerator. Cushions rotating shafts to reduce friction and noise. Order a new bushing today.

Fix SY EF error codes or warm refrigerator temperatures with this evaporator fan motor. Moderate DIY repair restores air circulation and cooling.

Secures the evaporator fan motor to its bracket for proper airflow. Replace if broken or missing to eliminate vibration, noise, or cooling issues.

LED light bulb illuminates your refrigerator interior. Replace when bulb burns out, flickers, or stops working. Verify fit with your model number.

Fix intermittent refrigerator operation caused by worn or heat-damaged component sockets. This receptacle restores secure plug-in connections for reliable performance.

Replace your refrigerator's control panel housing box if cracked, damaged, or missing. Encloses and protects internal control components. Direct fit.

Fixes refrigerator with no lights or unresponsive temperature controls. Restores power to control panel and display. Moderately difficult repair.

Fixes incorrect temperature readings and short cycling. This thermistor monitors fridge temps and signals the control board. Moderate DIY repair.

Replacement sensor cover cap for your refrigerator. Protects internal sensors from dust and damage. Order a new cover if yours is cracked or missing.

This genuine OEM part is the main control board for refrigerators. The main control board is the primary circuit board that controls the refrigerator's essential functions of maintaining and controlling temperature. If the refrigerator is no longer staying cool, powering on, or maintaining proper temperature, the main control board will need to be replaced. Luckily, this is a fairly simple repair.To begin, start by unplugging the refrigerator. Once unplugged, proceed to uninstall the inner door panel of the refrigerator by removing the mounting screws. Once removed, access the old control board. Remove the wire harness and any individual wires attached to the old board. After that, pull the old board out of its mounting brackets to fully remove it from the refrigerator. Reinsert the wires into their correct terminals on the new board and snap it into its mounting brackets. Once secured, reinstall the inner panel of the refrigerator and restore power to the appliance. This authentic replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand refrigerators.

Refrigerator door guide channel that helps align and support the door mechanism. Replace if cracked, broken, or worn to restore proper door alignment.

Replacement cover for refrigerator damper control assembly. Snaps into place over the control box. Replace if cracked, broken, or missing tabs prevent secure fit.

Replacement cover for refrigerator damper control assembly. Snaps into place over the control box. Replace if cracked, broken, or missing tabs prevent secure fit.

Protects and diffuses your refrigerator's interior light for even illumination. Replace if cracked, yellowed, or missing to restore proper lighting and safety.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Fix a fridge that's freezing food or not cooling properly. This air damper controls cold airflow between compartments. Moderate DIY repair for most models.

Seals the air damper opening to maintain proper airflow between compartments. Replace if torn or compressed to fix uneven cooling and drafts.

This filter wrench is a ring-style tool used to loosen or tighten a refrigerator's water filter housing or canister. It provides extra leverage to free a stuck filter cup and helps ensure an even, secure reinstallation.

• Provides leverage to loosen a stuck water filter housing/cup
• Assists with secure, even tightening during reinstallation
• Useful when the housing is difficult to turn by hand
• Helpful in tight spaces where hand access is limited

• Turn off the water supply and dispense water to relieve pressure
• Position the wrench around the filter housing/cup; turn counterclockwise to loosen
• After replacing the filter, tighten the housing until snug—do not overtighten
• Restore water supply and check for leaks

Reduces chlorine, lead, and contaminants in your drinking water and ice. Replace every 6 months for optimal performance. Verify fit by model number.

Replace your refrigerator's water filter cup if cracked, leaking, or frozen. Protects the filter and prevents leaks. Verify fit with your model number.

Seals water filter housing to prevent leaks in your refrigerator. Replace if water leaks when changing filters. Verify fit with your model number.

Holds water filter in place for proper filtration to ice maker and dispenser. Replace if cracked, leaking, or damaged. Confirm fit with your model number.

This is a push on John Guess design elbow used to connect two 5/16" plastic lines together.

Molded housing that directs airflow and protects blower components. Replace if cracked, broken, or missing to restore proper airflow routing in your unit.

Creates an airtight seal around your refrigerator door to keep cold air in and prevent frost buildup. Replace if torn, cracked, or loose. Confirm fit.

Wiring harness for refrigerators. Connects electrical components inside the appliance. Replace if wires are frayed, damaged, or connections are loose.

Protects wiring harness edges in your refrigerator from wear and abrasion. Replace if cracked, broken, or missing to prevent wire damage and insulation.

Replacement cover for refrigerator damper control assembly. Snaps into place over the control box. Replace if cracked, broken, or missing tabs prevent secure fit.

This is a push on John Guess design elbow used to connect two 5/16" plastic lines together.