Parts for Electrolux EFMG517STT0: 04 - Controls / Top Panel Parts

This pre-programmed user interface control board assembly manages the buttons and display on your appliance's control panel. Replacing a failed UI board restores responsive controls and accurate indications from the panel. What it does:

• Interprets keypad inputs and drives the display/indicator LEDs
• Sends user selections to the main control for proper operation
• Helps resolve an unresponsive or intermittent control panel
• Addresses blank, flickering, or garbled display behavior

• 1 pre-programmed user interface control board assembly

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD protection; handle the PCB by the edges only
• Photograph wiring and ribbon connections; match keyed connectors and orientation on reassembly
• Reuse existing mounting hardware, trim, and overlays as needed; ensure all harnesses are seated before restoring power

A replacement control knob assembly that restores reliable grip and control for a range or cooktop. Fits the original control shaft to allow safe selection of heat settings and accurate operation. What it does:

• Replaces cracked, stripped, or missing control knobs so you can adjust burners or oven controls securely.
• Provides a secure push-on fit to the control shaft for consistent response when turning.
• Helps resolve symptoms like loose spinning, slipping, or inability to change settings.
• Restores clear tactile feedback for temperature or burner selection.

• Disconnect power (and gas supply for gas ranges) before servicing to prevent shock, fire, or injury.
• Pull the old knob straight off the control shaft; align splines and push the new knob fully onto the shaft until seated.
• Test operation at low settings after reinstall to ensure proper fit and function.

This diffuser directs and evens airflow inside the appliance to promote consistent temperature and efficient operation. Replaces a damaged or broken diffuser to restore proper air distribution and reduce airflow noise. What it does:

• Guides cool or warm air from the blower/vent to improve circulation and temperature consistency
• Helps prevent hot or cold spots by evenly dispersing incoming airflow
• Replaces cracked, warped, or missing diffusers that can cause reduced airflow or noise
• Common symptom fixer: uneven cooling, fluctuating temperatures, or rattling/whistling near the vent

• Disconnect power to the appliance before beginning any repair
• Typically installs at the vent or blower outlet; common fasteners are clips or screws — keep hardware if replacing only the diffuser
• Handle plastic parts gently to avoid cracking; align tabs/slots before fastening

This metal top panel replaces the upper rear control housing on compatible Frigidaire ranges and stoves, restoring a secure mounting surface for controls and improving cabinet fit and appearance. Ideal for repairing bent, rusted, or damaged panels. What it does

• Replaces the upper rear housing that supports control knobs, switches and the backguard area
• Restores proper alignment and spacing between the cooktop and rear controls
• Stops light leaks and relieves stress from warped or bent panels
• Commonly used when the panel is dented, rusted, cracked, or has broken mounting tabs

• One top panel

• Disconnect power (and gas, if applicable) before starting any work
• Handle sharp sheet-metal edges with gloves; panel edges can be sharp
• Remove control knobs, backguard, or trim as required and save screws for reinstallation
• Align mounting tabs and secure with original hardware; test controls after reassembly

This damper is the refrigerator air-control flap that regulates airflow between compartments to help maintain consistent temperatures and proper cooling. It replaces a worn or stuck damper to restore normal airflow and temperature balance. What it does:

• Opens and closes to direct cold air where needed between freezer and fresh-food sections
• Helps maintain even temperatures and prevents one compartment from getting too warm
• Common symptom: uneven cooling or warm fresh-food section despite running compressor
• Common symptom: damper stuck or not moving, causing poor temperature control

• Disconnect power to the appliance before starting any repair
• Remove interior panels to access the damper; use basic hand tools
• Handle the damper and any wiring harness carefully to avoid damage
• After installation, verify damper operation and allow time for temperatures to stabilize

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic