Parts for Electrolux EFMG517STT0: 05 - Motor Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This spacer positions and supports adjacent components to maintain correct clearance and alignment inside the appliance, helping reduce vibration and rubbing for smoother, quieter operation. What it does

• Provides a fixed gap to keep panels, hinges, or trim pieces properly spaced
• Prevents metal-on-metal contact that can cause noise or wear
• Helps maintain door and component alignment for reliable sealing and operation
• A simple replacement for worn or missing spacers that cause rattling or misalignment

• Disconnect power to the appliance before starting any repair
• Remove the appropriate trim or access panel to reach the spacer
• Reinstall using the original fasteners; replace any corroded or damaged hardware
• If alignment issues persist after replacing the spacer, inspect surrounding mounts and hinges

Replacement refrigerator door gasket that restores a tight seal around the door to help maintain proper temperatures and reduce energy loss. Designed as a direct-fit replacement to stop air leaks and improve cooling performance. What it does:

• Seals the door perimeter to prevent cold air from escaping and warm air from entering
• Helps reduce frost build-up and condensation inside the compartment
• Restores consistent temperature for better food preservation
• Can improve energy efficiency by eliminating gaps that cause the compressor to run more

• Unplug the appliance or turn off power before beginning work
• Remove the old gasket by loosening retainer screws or pulling it free from the door channel per your model's service instructions
• Seat the new gasket fully into the door channel; warm it with a hair dryer or hot water (carefully) if needed to improve flexibility and fit

This replacement refrigerator door gasket seals the door to help maintain proper temperature and reduce energy loss. It restores a tight seal around the door edge for more consistent cooling and food freshness. What it does

• Forms a weather-tight seal around the refrigerator door to help keep cold air in and warm air out
• Helps reduce frost buildup and energy waste from a failing or torn seal
• Common symptom: visible gaps, torn or brittle gasket, or warm spots near the door edge
• Works as a direct-fit replacement when the factory gasket is worn, cracked, or misshapen

• Disconnect power to the appliance before attempting replacement
• Clean the door flange and seating area before installing the new gasket for best seal
• Soften and shape the gasket as needed (warm water or gentle heat can aid flexibility) and ensure the magnetic edge seats fully

A single replacement screw used to secure appliance trim, panels, or interior components. Replaces lost or damaged fasteners so panels and assemblies stay firmly attached and appliances operate safely. What it does:

• Secures trim pieces, control panels, brackets, or interior components
• Restores proper fit and alignment when panels are loose or rattling
• Helps eliminate vibration noise caused by missing or stripped screws
• Used wherever the OEM screw specification is required for reliable fastening

• Install with the matching screwdriver or driver bit; avoid over-tightening to prevent stripping
• Disconnect power and remove or support panels as needed for safe access
• If screw threads are damaged, replace with the exact OEM screw to ensure secure fit

The Outlet Thermal Fuse is an OEM part for Frigidaire dryers. It acts as a safety device that protects the dryer from overheating by cutting off the power if the temperature exceeds a safe level. This ensures the dryer operates safely and helps prevent potential fire hazards.

Causes of a bad thermal fuse can include lint buildup blocking airflow, overloading the dryer, or mechanical failures in the heating element. These issues can cause the dryer to overheat, leading to the fuse blowing as a protective measure.

Symptoms of a bad outlet thermal fuse include:

• The dryer not starting
• The dryer running but not heating
• Sudden stopping during a cycle
• No power to the dryer

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Blower Wheel Assembly is an OEM part for Frigidaire dryers. This part circulates air through the drum and exhaust it outside the dryer.  

Causes of a bad blower wheel assembly include wear and tear from prolonged use, obstruction by lint or debris, and physical damage to the wheel or its mounting.

Symptoms of a bad blower wheel assembly include:

• Reduced drying efficiency
• Unusual noises during operation, such as rattling or squeaking
• Overheating of the dryer
• Poor airflow from the exhaust vent

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This blower assembly circulates air inside the appliance to help maintain even temperatures and proper cooling. Replacing a faulty blower restores airflow for more consistent performance. What it does

• Moves air across the evaporator and throughout the compartment for consistent cooling
• Commonly replaces units that make unusual noise or wobble while running
• Restores airflow when cooling is uneven or the appliance struggles to maintain temperature
• Helps prevent frost buildup when airflow is compromised

• One blower assembly

• Disconnect power before servicing to avoid electric shock
• Remove the access panel(s) and any shelving or components blocking the blower for safe access
• Handle sharp sheet-metal edges carefully and note blower orientation for correct reinstallation

This small spacer fits on the idler assembly shaft to properly space and align the belt tensioner. Replacing a worn spacer helps keep the drive belt tracking correctly so the drum/tub runs smoothly and quietly. What it does:

• Spaces and centers the idler pulley on its shaft
• Helps maintain proper belt alignment and tension
• Can reduce squeaking or chirping from the idler area
• A worn or missing spacer may let the belt ride off, fray, or stop the drum/tub

• 1 idler spacer

• Disconnect power before servicing; let hot components cool
• Access the idler assembly per your model, relieve belt tension, and remove retaining hardware to slide off the pulley and old spacer
• Install the new spacer in the same location/orientation; reassemble and route the belt correctly
• Rotate the drum/tub by hand to verify smooth belt tracking before restoring power

Replace a failed thermistor with this factory temperature sensor. It monitors temperature and feeds that data to the control, helping the appliance regulate heat and run cycles correctly. A faulty sensor can cause temperature-related performance issues.

• Senses temperature and sends a resistance signal to the control board for regulation
• Helps maintain proper heating/temperature during operation
• Failure may cause no heat or overheating, erratic or extended cycles, or temperature/sensor error codes
• Replace when sensor is open/shorted or readings are out of range per service diagnostics

• Disconnect power before servicing; if applicable, also shut off water or gas supply
• Access the sensor, unplug the wire connector, and remove any mounting screw/clip
• Install the new sensor; transfer any bracket/seal from the original and route wiring away from hot or moving parts
• Run a diagnostic or test cycle after replacement to confirm normal operation

This hex head screw spacer is a replacement threaded fastener that secures and spaces components while cutting its own thread in softer mating material for a tight fit. It's useful for repairs where the original spacer screw is missing or damaged. What it does:

• Acts as a spacer and fastener to hold panels, brackets, or assemblies at a set distance
• Thread-cutting tip forms secure threads in compatible materials for reliable engagement
• Helps stop movement or vibration of connected parts that can cause noise or wear
• Commonly used where the original hex-head spacer screw is corroded, stripped, or broken

• Use the correct screwdriver or wrench on the hex head to avoid rounding the fastener
• Start threads straight and apply steady pressure; do not force if resistance indicates misalignment
• Use appropriate torque — overtightening can strip the formed threads or damage parts
• Wear eye protection and follow appliance power/disconnect safety before servicing

This replacement pulley guides the drive belt so the drum or tub turns smoothly and reliably. A worn pulley can squeal, shred belts, or stop the load from tumbling or spinning.

• Guides the drive belt and helps transfer motor power to the drum/tub
• A seized or damaged pulley can cause the drum/tub not to turn or to stall
• Inspect for cracks, wobble, or rough bearings during diagnosis

• Disconnect power before servicing; if working on a gas dryer, also shut off the gas supply. For washers, turn off water.
• Access the belt path; release belt tension and remove the old pulley.
• Install the new pulley and route the belt correctly; rotate by hand to confirm smooth tracking.
• Inspect and replace a worn drive belt or related belt-drive components while open.

This idler spring attaches to the idler arm to keep the drive belt properly tensioned, preventing slip and chatter. Replacing a weak or broken spring restores steady rotation and helps reduce noise and belt wear.

• Maintains correct belt tension by pulling the idler arm into position
• Helps prevent belt slippage, squealing/chirping, and premature belt wear
• A failed spring can cause no or intermittent rotation and the belt coming off
• Typical signs include a loose belt, off-track belt, or rhythmic squeak from the base

• Disconnect power before servicing; if working on a gas appliance, shut off the gas supply
• Access the idler assembly; note belt routing before removal
• Relieve belt tension, then move the idler arm to remove and replace the spring on the same mounting holes
• After reassembly, rotate by hand to verify smooth belt tracking before test

The Idler Arm Assembly is an OEM replacement part for Frigidaire clothes dryers. It is a pulley assembly that helps to guide the dryer belt and keep it aligned. The idler arm assembly is typically located on the front of the dryer, near the dryer drum.

Causes for replacement include worn bushings or broken linkage from constant mechanical movement over several years.

Symptoms of a faulty idler arm assembly are:

• Dryer drum failure to rotate or revolve during the cycle
• Unusual vibrations, clunks, or knocks from within the dryer
• door during operation
• Slipping or shredding belts from lack of pulley engagement

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Drive Belt is an OEM replacement part for Frigidaire dryers. It plays a crucial role in transferring the rotational motion from the dryer's motor to the drum, enabling the tumbling action necessary for drying clothes.

Symptoms of a need to replace the drive belt include:

• The dryer drum not turning or rotating during cycles
• Loud thumping or squeaking noises coming from the dryer
• Visible wear, cracks, or fraying on the existing belt

Causes of a faulty drive belt can include general wear and tear over extended use, exposure to high temperatures or lint buildup, physical damage from foreign objects, or manufacturing defects in the belt material or construction.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dryer models. 

The Motor Mounting Clamp is an OEM part for Frigidaire dryers. This clamp secures the motor in place within the dryer, ensuring it operates smoothly and remains stable during the drying cycles. The motor mounting clamp is essential for maintaining the proper alignment and function of the dryer motor.

Over time, the motor mounting clamp can become worn out or damaged due to constant vibration and movement. Accidental impacts or mishandling during maintenance can also cause the clamp to fail, leading to motor misalignment or instability.

Symptoms of a bad motor mounting clamp include:

• Excessive noise or vibration during the drying cycle
• Motor shifting or moving within the dryer
• Reduced drying efficiency
• The dryer not starting or stopping abruptly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Dryer Motor is an OEM part for Frigidaire dryers. It is responsible for turning the drum and the blower wheel to circulate air through the dryer, enabling efficient drying of clothes.

The dryer motor can become faulty due to normal wear and tear, electrical issues, or overheating. If the motor fails, the dryer will not be able to operate correctly.

Symptoms of a bad dryer motor include:

• The drum not spinning
• The dryer not starting or shutting off mid-cycle
• Unusual noises such as humming, buzzing, or grinding
• A burning smell or overheating

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Bracket is an OEM part for Frigidaire clothes dryers. Internally installed, this L-shaped bracket securely anchors heavy rotating components like the belt pulley assembly and motor in correct alignment.

Causes of failure could include fatigue cracks from years of absorbing vibration stresses during active cycles. Corrosion risks increase further with repeated heating and moisture exposure over time as well.

Symptoms of a problematic bracket consist of:

• Noisy operation or shaking felt within the dryer 
• Components detaching or rotating out of intended position
• Visible cracks compromising secure mounting integrity

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.