Parts for Electrolux E36GC75PSS0: 02 - Cooktop Parts

The Ignitor Screw is an OEM component for Frigidaire ranges and ovens. It secures the igniter, a critical heating element that sparks to ignite the gas burner. 

Causes of a bad ignitor screw can include damage or stripping of the screw head from repeated removal/installation of the igniter component over time.

Symptoms of a bad ignitor screw include: 

• The igniter shaking loose and becoming disconnected
• Inability to properly tighten the igniter securely in position
• Lost or stripped screw

This genuine Frigidaire replacement screw restores secure mounting of the igniter. Proper fastening is necessary for consistent and reliable ignition of cooking appliances.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This control panel is the exterior console component that provides the user interface and housing for the appliance's buttons and display, restoring a finished look and usable controls. What it does

• Replaces a cracked, scratched, or damaged front console panel to restore appearance and button alignment.
• Supports the appliance's control buttons and display openings so buttons operate correctly.
• Helps protect underlying electronics from dirt and debris where the enclosure is required.
• Commonly replaced when cosmetic damage or physical warping interferes with button use.

• One control panel (front console) as shown.

• High-level replacement only: remove power to the appliance before servicing.
• Access typically requires removing trim or screws; handle gently to avoid damaging clips.
• Take care to align tabs and connectors during reassembly; do not force parts into place.

This replacement cooktop grate restores a stable, level surface for cookware on gas ranges. It helps protect the burner area and keeps pots and pans steady during cooking for safer, more consistent results. What it does:

• Supports cookware above the burner for even heating and safer handling
• Protects the cooktop and burner components from spills and direct contact
• Replaces cracked, chipped, warped or unstable grates that cause rocking cookware
• Helps maintain proper flame exposure for efficient cooking performance

• Designed for drop-in replacement; lift out the old grate and set the new grate into place
• Allow burners and components to cool completely before attempting replacement
• Clean grate with nonabrasive cleaner; avoid harsh chemicals that could damage finish

This insulating cap protects compressor electrical terminals by covering the connection area to help prevent shorts and moisture intrusion. It's a simple replacement that restores proper terminal insulation and safety. What it does

• Covers compressor terminal studs to reduce risk of electrical shorting and arcing
• Helps shield terminals from dust, debris and incidental moisture
• Maintains safe separation between wiring and metal chassis
• Can stop intermittent electrical contact that causes compressor cycling issues

• One insulating cap for compressor terminal protection

• Disconnect power before servicing the appliance to avoid shock or injury
• Remove old cap by gently pulling away from terminal studs; press new cap fully into place
• Inspect terminal connections and wiring for damage; replace any corroded or frayed components

The Range Cap is an OEM part for Frigidaire ranges. It seals the upper combustion chamber to contain heat from the oven burners. A tight-fitting cap is critical for efficient, safe oven performance.  This cap measures 3 inches in diameter.

Causes of a bad cap can include cracks, warping, or collapsed seals from prolonged exposure to high oven temperatures. Accidental damage during past maintenance is also possible.

Symptoms of a bad cap include:

• Escaping heat from the oven chamber, reducing efficiency
• Flames or sparks visible around the cap during baking
• Loose, wobbly, or missing cap allowing grease and debris in the combustion area

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Burner Cap is an OEM part for Frigidaire cooktops and ranges. It is designed to cover the burner head, ensuring an even distribution of the flame for efficient cooking. The burner cap also protects the burner head from spills and debris, which can affect performance.

You should replace the burner cap if it becomes damaged or worn out. Causes of a bad burner cap can include exposure to high heat, buildup of food residue, or accidental impacts. A compromised burner cap can lead to uneven flames, inefficient cooking, or difficulty in lighting the burner.

Symptoms of a bad burner cap include:

• Uneven or yellow flames
• Difficulty in igniting the burner
• The burner cap being cracked, chipped, or discolored
• Poor cooking performance or hotspots on cookware

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Surface Burner Cap is an OEM part for Frigidaire gas ranges. It sits atop the surface burner and helps to distribute the gas flame evenly for consistent cooking performance. The cap also protects the burner head from spills and debris.

You should replace this surface burner cap if it becomes damaged or worn out. Signs of damage include chipping, cracking, or discoloration due to prolonged exposure to high temperatures or cleaning agents.

Symptoms of a bad surface burner cap include:

• Uneven or unstable flame
• Difficulty in igniting the burner
• Visible cracks or chips on the cap
• Food cooking unevenly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This burner seal is a replacement gasket that fits around a surface burner to help keep food and liquids out of the cooktop cavity and make cleanup easier. Simple wear replacement for torn or collapsed seals. What it does:

• Forms a protective gasket between the surface burner and cooktop to limit spills and debris entering the cavity
• Helps keep the burner cap seated correctly and reduces grime buildup around the burner area
• Makes routine cleaning faster by preventing trapped food and liquid
• Common signs you need this part: visible gap or torn seal around the burner, frequent debris buildup, or a burner cap that sits uneven

• Turn off the cooktop and gas supply and allow all parts to fully cool before starting.
• Remove the burner cap and lift out the old seal; align and press the new seal into place around the burner opening.
• Reinstall the burner cap, restore power/gas, and test burner operation for correct seating and appearance.

This burner seal is a replacement gasket that fits around a cooktop burner to help keep the burner area sealed and easier to clean. It helps maintain a proper seal between the burner base and the cooktop surface. What it does:

• Seals the gap between the burner and cooktop to limit food, grease and liquid from entering the burner cavity
• Helps keep the burner seated and reduces wobble or misalignment
• Supports cleaner cooktop surfaces and simplifies wipe-downs
• Can help maintain consistent ignition area by keeping debris away from the burner base

• Turn off power to the appliance and ensure the cooktop is completely cool before starting.
• Remove burner grate and lift off the burner cap and burner head as needed to access the seal.
• Clean the seating area of any grease or debris, then press the new seal evenly into place before reassembling.

This surface burner seal sits between the burner and the cooktop opening to block spills and air leaks, helping the burner seat correctly and keeping the cooktop area cleaner.

• Creates a tight seal between the surface burner and the cooktop opening
• Helps prevent liquids and debris from getting under the cooktop
• Supports proper burner alignment and consistent heat/flame
• Replace if torn, brittle, swollen, or permanently compressed; common signs include seepage under the top, uneven heating/flame, or the burner not sitting level

• Disconnect power; for gas ranges, also shut off the gas supply. Allow the cooktop to cool completely.
• Remove grates, burner cap, and burner head/base as applicable; lift off the old seal.
• Clean the mating surfaces; position the new seal evenly around the opening.
• Reassemble burner parts and test for proper seating and even heating/flame.

Replacement control knob for select ranges and cooktops. It mounts to the valve or switch stem so you can turn a burner or oven function on and choose a setting, restoring safe, reliable control. What it does:

• Attaches to the control shaft to operate a burner valve or control switch
• Provides on/off and level/temperature selection
• Common symptoms: cracked or broken knob, stripped insert/splines, loose or falling off, or inability to turn the control shaft
• Restores positive, accurate feel when selecting settings

• 1 control knob

• Disconnect power; ensure all burners are cool. For gas units, shut off the gas supply if needed.
• Pull the old knob straight off the stem; avoid prying against the bezel/control panel.
• Align the shaft flat/splines with the new knob and press straight on until fully seated.
• Test operation to confirm proper orientation and engagement.

This control panel is the replacement user interface cover that houses the appliance controls and display, restoring a clean, functional front surface and protecting the underlying electronics from damage. What it does

• Provides the visible control surface and button area for user operation
• Protects internal control boards and wiring from spills, dust, and impact
• Restores proper fit and appearance when the original panel is cracked or damaged
• Can resolve symptoms such as unresponsive buttons, missing/obscured indicators, or loose trim around the controls

• One control panel

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle panel edges carefully; some panels have sharp edges or fragile clips
• Installation typically requires removing trim/screws and carefully disconnecting/reconnecting any button membranes or display assemblies

This replacement door gasket creates a tight seal around the refrigerator or freezer door to help maintain interior temperature and reduce energy loss. It restores proper door closure for better cooling and frost prevention. What it does:

• Seals the door perimeter to keep cold air in and warm air out
• Helps maintain consistent internal temperatures for food safety
• Reduces frost build-up and compressor runtime due to air leaks
• Restores proper door alignment and closing performance

• Remove old gasket and clean the door mating surface before installing the new gasket
• Start installation at a corner and work around the door to ensure an even fit
• Gasket may be warmed slightly (hot water or hair dryer on low, if needed) to improve flexibility for positioning
• Unplug or disconnect power to the appliance before beginning work

Cerama Bryte Cooktop Cleaner is a special cleaner designed specifically for ceramic glass and smooth-top cooking surfaces. It easily removes cooked-on foods, spills, or grease while leaving your cooktop looking like new. This product contains no abrasives or harsh chemicals, so it won’t scratch or damage your delicate cooktop surface.

To use the cleaner effectively, all you need to do is spray it onto the surface and then scrub it with a clean damp cloth. Use circular motions for best results. The product can also be used to remove baked-on foods from grates and drip pans on your stovetop. For tougher stains, let the cleaner sit for a few minutes before wiping it away.