Craftsman Tiller Parts

This is a starter housing assembly that is often a part of tillers and string trimmers. It is made for gas-powered tools and is composed of durable metal. The starter housing assembly is responsible for helping to start the tool when a user pulls on the starter rope to engage the engine. The starter housing assembly comes with plastic housing, the starter pulley, the pull rope, and the recoil spring. It also includes the hardware needed for a replacement.The primary tool needed to replace a broken or damaged starter housing assembly is a wrench. The first step is to take the tool and place it on a flat surface before disconnecting the spark plug wire. Take out the screws that secure the starter housing assembly to the tool so it can be removed. Take the new component and secure it using the original or new screws.This starter housing assembly is sold as an individual part. The item is an authentic OEM replacement part that is directly sourced from the manufacturer. This component is created for use with tillers and string trimmers manufactured by MTD and Craftsman.

This o-ring is a genuine OEM part sourced from the manufacturer for use in many parts of engines in lawn and garden equipment. The o-ring is a type of gasket but is not flat like a gasket. It is circular and made of rubber. It is seated in a groove on the engine part and is compressed against another part to create a seal. This seal keeps air and fluids from entering or exiting the sealed part. Like gaskets, o-rings must be periodically inspected and replaced to ensure proper engine performance.Visual inspection of o-rings will reveal nicks, indentions, cuts, or tears on the surface of the o-ring. If the rubber has warped due to excessive heat, it will not fit properly and will need to be replaced. The replacement may not require tools, depending on the location of the rubber gasket. Remove the bad o-ring and wipe both sides of the area to remove the old grease. Apply fresh grease to the o-ring before installing it to ensure a tight seal. Press the new o-ring firmly in the groove before attaching the connecting part. If the ring does not seat well or has to be stretched to fit, discard and start with a new o-ring.The o-ring is sold individually. It is designed for trimmers and tillers. It is compatible with Craftsman, MTD, Bolens, Troy-Bilt, and Cub Cadet.

The design and purpose of the O-ring is relatively self-explanatory. It is an “O” shaped ring used as a gasket in lawn and garden equipment. It is designed to sit within a groove and be compressed during assembly. It creates a perfect seal that blocks the path of liquids or gases from escaping or flowing into regions of the machine where they are not supposed to be.The O-ring may be damaged if an outdoor piece of equipment is struggling to start or run. After checking the air filter cover, removing the carburetor, and cleaning it thoroughly, the next step is to replace the O-rings, carburetor gasket, and air filter, followed by the spark plug. Regular maintenance of the carburetor and routine evaluation of the suitability of the O-ring is essential to proper mechanical maintenance.This O-ring is a genuine OEM part sourced directly from the manufacturer, and it is sold individually. The manufacturer of this product is MTD. Examples of compatible products and machines includes trimmers, tillers, weed wackers, brush cutters, and leaf blowers or leaf vacuums. It is compatible for products made by the following brands: MTD, Cub Cadet, Craftsman, and Troy-Bilt.

This short block assembly is a genuine MTD part, sold individually. This short block assembly can be used as a replacement part for a string trimmer, a tiller, or an edger. The short block includes the crankshaft, piston, rod, camshaft, valves, and governor. A short block assembly might be necessary if there is damage to a wide range of parts in the equipment's engine. Check for frequent stalling, misfires, or an inability to power on. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This short block assembly is compatible with the following brands: MTD, Craftsman, and Cub Cadet.

This replacement part is a screw knob. This is a genuine replacement part made by MTD. This screw knob is used in different types of machinery and appliances. This screw is easily gripped to remove and replace easily and quickly. A new screw knob might be needed if it is so worn that the user can no longer grip the screw. This can be due to wear and tear after years of normal use. If the screw part has become stripped it is recommended that it be replaced as soon as possible. This should be a fairly easy replacement and only require common household tools. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use. This screw knob is also sold individually and is sourced directly from the manufacturer.

This part is a replacement ignition coil. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part's intended use is to replace a broken or defective ignition coil in cultivators.Ignition coils are important for powering the cultivator as they generate the voltage that travels to the equipment's spark plugs. If the ignition coil is faulty, the cultivator may have decreased power or may not work at all, thus this part may need to be replaced. Disconnect the spark plug wire before installing the ignition coil. It's important when working on or near an engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this ignition coil, reference the appropriate owner's manual and specific equipment diagrams.This is an authentic OEM replacement part made of high-quality materials. This ignition coil can be used with different models of cultivators that have been manufactured by MTD, Craftsman, Troy-Bilt, and other brands. Sold individually.

This is a genuine replacement fuel tank for a tiller. The fuel tank holds fuel for the tiller and connects fuel tubes to distribute fuel to the engine. Tiller fuel tanks may start to leak if it is cracked, punctured, or otherwise damaged. In addition to losing fuel, this is a serious safety hazard. If damaged, this part should be replaced before using the tiller. Do not attempt to repair a damaged fuel tank.Fuel tank replacement is a simple process. This project will require different tools depending on the model of tiller. Remove the fuel lines and fuel tank completely from the tiller. Remove the tiller fuel tank by unscrewing any bolts connecting the fuel tank to the engine. Set up the new fuel tank with the filter, fuel level indicator, and fuel cap. Reinstall the fuel lines from the engine to the fuel tank, and reattach the new fuel tank with the previous or new bolts.This is a genuine OEM replacement part. This part is compatible with Craftsman, Troy-Bilt, and MTD brands. This part is sold separately.

This genuine OEM replacement part idler pulley plays an important part on many lawn tractors, mowers, and snowblowers. It drives the engine's belt system, particularly the belts connected to the crankshaft. It helps to create motion throughout the engine, including in the steering pump, air compressor, and the alternator. Therefore, without this pulley, the engine will not function properly. As with any part of an engine, an idler pulley will begin to wear down over time. When this happens, an idler pulley will begin slipping, causing the belts to no long run smoothly. If an idler pulley breaks completely, the engine will not start. Before replacing an idler pulley, be sure to let the engine cool completely, as you will have to remove several parts with a screwdriver and socket wrench set. This idler pulley will work with Troy-Bilt, Yard Machines, MTD, Cub Cadet, and Yard Man appliances. It is a high-quality replacement part sourced directly from the original manufacturer. This part ships individually.

This replacement screw is useful for many different types of handheld outdoor equipment. Screws are used as a means to hold parts of the machine together. The screws also help to reduce the amount of vibration that occurs in the machine.These screws are used in outdoor equipment, so there is a chance they could corrode over time. In some cases, the screws may also lose their thread, or the heads of the screws could start to become worn down. Owners who notice issues with the screws, or who notice a missing screw should replace them to ensure the proper function of the machine. Failure to replace damaged screws could result in more difficulty replacing them after they wear down further.The screw works on various types of equipment including blowers and trimmers. It is compatible with a range of brands including Murray, Craftsman, Yard Machines, Bolens, Yard-Man, Craftsman, Ryobi, and McCulloch. This is a genuine OEM part sourced from the manufacturer, and it is sold individually.

This is a hi-pro key, or high profile key. This part is most commonly used to lock pulleys and gears into transmission shafts. Replacing a damaged, broken or lost hi-pro key is simple, requiring only a set of pliers to complete.This hi-pro key is an authentic OEM component sourced directly from the manufacturer. It is sold as an individual unit. It is compatible with lawn tractors and snowblowers from MTD, Ryobi, Yard Machines, Bolens, Yard-Man, Troy-Bilt, Cub Cadet, and Huskee. It is made of high-quality, durable metal materials.

This is a spring switch that is used in many types of lawn and garden equipment, such as log splitters, lawnmowers, and tillers. The spring switch is made out of durable metal and is typically located near the switch button. With ordinary use, the spring switch can experience wear or other types of damage and stop working correctly. When this occurs, it will need to be replaced.If the spring switch is broken or bent, a screwdriver will be needed to replace it. The lawn equipment should be powered off and placed on a stable surface during the replacement. Disassemble the unit and locate the contacts to access the spring switch and other small parts. The original switch can be removed using a screwdriver so the new component can be installed. Reassemble and power the tool on before use.This spring switch is a genuine OEM replacement part that is sourced directly from the manufacturer. The component is sold on an individual basis. The part is made to be compatible with lawnmowers, snowblowers, tillers, log splitters, and wood chippers manufactured by Craftsman, Toro, Cub Cadet, Ryobi, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, MasterCut, and Turf King.

A ball bearing is a common type of rolling-element bearing. It will use balls to keep space between the bearing races and eliminate friction and contact between moving parts. Ball bearings used in lawn and garden equipment ensure that axial loads and radial loads are evenly supported and that there is only a limited amount of rotational friction on the component. It distributes weight evenly, but will undergo constant wear and tear from vibration, heat, and friction and will need replacement regularly. This ball bearing is a genuine OEM part suited to use in Craftsman, Cub Cadet, Ryobi, Troy-Bilt, MTD, Huskee, Yard Machines, Bolens, Mastercut, and Yard-Man equipment. It may be needed for repair work done on a lawnmower, snowblower, tiller, edger, or a log splitter.