Crosley Range Parts

Size: 8 inch. 2200 watt. Radiant.

This surface element supplies heat to an electric range or cooktop burner. When it fails, the burner may not heat or may heat inconsistently. Replacing the element restores steady, reliable cooking performance.

• Converts electrical energy into heat for the cooking zone
• Works with the surface control (infinite switch) to regulate temperature
• Common symptoms: burner won't heat, intermittent or uneven heating, visible breaks/blistering, burnt/melted terminals
• A failed element will not glow or reach set temperature when energized

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• If your model uses a plug-in coil style: remove the drip pan, pull the element straight out of the receptacle, and inspect/replace a heat-damaged receptacle as needed
• If your model uses an under-glass radiant style: lift the cooktop, transfer any clips/limiters from the old element, and route wires exactly as original
• After reassembly, test the burner at a low setting to ensure proper operation

This surface burner knob fits the valve stem for a cooktop/range burner control. It restores a secure grip and accurate adjustment when the original knob is cracked, stripped, loose, or missing.

• Attaches to the surface burner valve stem to turn the burner on/off and adjust flame level
• Replaces a knob that slips, won't stay on, cracks, melts, or free-spins
• Helps restore proper Off alignment and a clean, finished look

• Ensure all controls are in the Off position; disconnect power and shut off gas as a safety precaution
• Pull the old knob straight off the valve stem—do not pry sideways
• Align the flat/D-shaped opening with the valve stem and press firmly until fully seated
• Verify smooth operation and correct Off alignment before restoring power/gas

Color: black. It measures about 2 inches in diameter.

This surface burner grate supports cookware on your gas cooktop, keeping pots and pans stable above the flame. Replace a cracked or warped grate to restore safe pan support and consistent burner performance.

• Holds cookware at the proper height above the burner flame
• Provides a stable, level surface for pots and pans
• Replace if cracked, warped, or missing to prevent wobbling or tipping
• Common symptoms include unstable cookware, uneven heating, or visible damage to the grate

• Turn all burners off and allow the cooktop to cool completely before handling
• Lift off the old grate and clean the area if needed
• Position the new grate so its feet sit flat and openings align with burner caps
• Test with a pan to confirm it sits level and stable

The Burner Grate is an OEM part for Frigidaire gas ranges. It supports racks and pans directly over the range's gas burners during cooking. The burner grate must withstand constant exposure to high heats without warping or degradation.

Causes of a bad burner grate include wear from heavy use over multiple years, corrosion from spills or food particles left on the grate, or cracks and chips that compromise durability and function.  

Symptoms of a bad burner grate are:

• Uneven or inefficient heat transfer to pots and pans during cooking  
• Warping or distortion of grate bars impacting pan support
• Sharp edges or breakage causing potential safety hazards

This OEM replacement grate is also compatible with some Electrolux, Crosley, and Amana gas ranges. 

Replacement cold control that restores temperature regulation in compatible refrigerators. Installs behind the temperature knob to control compressor cycling, helping stabilize interior temperature and stop constant running or temperature swings. What it does:

• Regulates refrigerator temperature by switching compressor/fan operation on and off.
• Replaces a failed temperature control that causes inconsistent cooling or interior temps that are too warm or too cold.
• Can stop issues like the compressor running continuously or frequent temperature fluctuations.
• Works with compatible refrigerator control housings and knobs.

• Disconnect power before replacing the control to avoid shock or injury.
• Note wire locations and knob orientation before removing; reconnect wires to the same terminals.
• Handle the control carefully and avoid bending or stressing mounting tabs and contacts.
• After installation, restore power and verify proper cycling and temperature stabilization.

Color: White

This burner valve knob replaces a worn or missing surface burner control so you can turn the gas on/off and set flame levels precisely. It restores smooth, secure control of your cooktop's surface burners.

• Mounts to the surface burner valve stem to control gas flow and flame height
• Restores accurate turning and feel when the original knob is cracked, stripped, or loose
• Common symptoms: knob falls off, won't engage the stem, hard to adjust flame, missing knob
• Helps ensure the burner reliably turns fully Off and adjusts smoothly through settings

• Turn all controls OFF and allow the cooktop to cool before servicing
• Unplug or disconnect power to the range for safety
• Pull the old knob straight off; align the new knob with the valve stem (match the flat/D-shaped side) and push straight on—do not force
• Confirm smooth operation and proper Off alignment after installation

This white switch knob replaces a damaged or missing control knob, restoring a clean look and smooth, confident operation when selecting settings. It press-fits onto the control shaft so you can adjust functions without wobble or slip.

• Attaches to the control switch shaft to turn and select settings
• Replace if the knob is cracked, stripped, loose/wobbly, or missing
• Common symptoms: knob falls off, won't engage the switch, or is hard to turn
• Normal wear, heat, or impact can damage the original knob over time

• Disconnect power and ensure the appliance is cool before servicing
• Pull the old knob straight off the shaft; avoid prying against the panel or switch stem
• Align the new knob with the shaft and press straight on until fully seated
• Verify alignment with the OFF position and test operation

This door handle spacer fits between the handle and the door panel, providing the correct standoff and a clean, finished look. Replacing a worn spacer helps keep the handle secure and aligned.

• Maintains proper spacing between the handle and door surface
• Helps stabilize a loose or wobbly handle
• Replaces cracked, discolored, or missing spacers
• Color: Bisque (cream/tan finish) to match compatible appliances

• Disconnect power and allow the appliance to cool before servicing
• Support the door and handle while removing mounting screws
• Transfer or replace spacers on both sides of the handle if needed; do not overtighten screws
• Wear gloves to protect hands and avoid stressing glass panels

This replacement switch restores reliable on/off control for a specific function in the appliance, helping the selected feature respond consistently when operated.

• Controls electrical power to a designated circuit or component when actuated
• Sends an on/off signal to the control or directly to the component it operates
• Failure symptoms can include no response, intermittent operation, or a switch that feels loose, sticks, or is hard to press
• May show signs of heat damage, arcing, or a burning smell near the control area when faulty

• Disconnect power at the breaker before servicing to avoid electrical shock
• Access location varies by model; remove the control panel, backguard, or front panel as needed
• Label or photograph wire positions and transfer them one at a time to the new switch
• After reassembly, restore power and test operation of the associated function

This white control knob replaces a worn or missing knob so you can smoothly select settings on your appliance again. It restores dependable turning feel and a clean, like-new appearance on the control panel.

• Attaches to the control shaft so you can select levels or functions
• Common fix for cracked, stripped, loose, or missing knobs
• Helps when the knob spins freely or is hard to turn
• Maintains clear alignment with the panel's indicator marks

• Disconnect power and, if applicable, shut off gas before servicing
• Pull the old knob straight off the shaft
• Align the new knob with the flat or splined shaft and press on until fully seated
• Verify smooth movement from OFF through all settings

The Knob is an OEM part for Frigidaire ranges. It is responsible for controlling the various functions and settings of your range, allowing you to adjust the temperature and operate the burners.

A bad knob can occur due to wear and tear over time, accidental damage, or exposure to heat and moisture. Signs of a faulty knob include difficulty in turning, a loose or wobbly fit, or the control markings wearing off.

Symptoms of a bad knob include:

• Difficulty in turning or adjusting 
• The knob feeling loose
• Cracks or discoloration 

Replace your worn-out or damaged range knob with this genuine OEM Frigidaire part to restore your range. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Color: White

This glide restores smooth, aligned movement for a refrigerator or freezer drawer so the drawer opens and closes without sticking. Use it to replace a worn or broken glide and reduce scraping, binding, or uneven travel. What it does:

• Guides and supports the drawer so it tracks straight and slides smoothly.
• Replaces worn or damaged glides that cause drawers to stick, bind, or scrape.
• Helps prevent the drawer from coming off the track or shifting out of alignment.
• Reduces noise and uneven movement during opening and closing.

• Disconnect power (unplug the appliance) before servicing to avoid electrical hazards.
• Remove the drawer and any obstructing shelves per the OEM instructions to access the glide.
• Keep or replace original mounting screws; ensure the glide is oriented and seated correctly before tightening.
• Replace those parts to ensure a secure fit.

This pressure regulator controls incoming water pressure to the appliance's water/ice system, helping maintain steady flow for proper dispenser and ice maker operation. Replaces a worn or failing regulator to restore correct water delivery. What it does:

• Reduces and stabilizes incoming household water pressure for the appliance's water valve/ice maker
• Helps prevent overfilling, leaking, erratic dispenser flow, or poor ice production caused by excessive pressure
• Works with the water inlet system to ensure consistent fill cycles and reliable dispensing
• Compatible with models that use WP74006429 as the factory regulator

• One pressure regulator

• Shut off water supply and unplug the appliance before replacing the regulator
• Inspect fittings and tubing for damage; replace any worn connectors or seals
• Tighten fittings securely and check carefully for leaks after restoring water and power