Crosley Range Parts

The Range Clock Knob is an OEM part for Whirlpool ranges. It attaches to the center of the oven control panel and allows users to adjust the built-in clock, serving as the primary control for setting or correcting the time. 

Over time, the clock knob can become faulty due to regular use leading to internal stripping or wear, exposure to heat causing cracks or warping, or accidental impacts damaging the knob.

Color: Black

Symptoms of a defective range clock knob include:

• Difficulty setting or adjusting the clock
• The knob spins freely without engaging the control shaft
• The knob feels loose, cracked, or broken

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ranges.

This replacement power cord restores electrical connection to the appliance so it can receive mains power safely. Use it when the original cord is frayed, damaged, or no longer providing a reliable connection. What it does:

• Replaces a damaged or worn appliance power cord to restore reliable power
• Resolves intermittent power, sparking at the plug, or visible cord damage
• Provides the necessary insulated conductors for safe appliance operation
• Works as a direct cord-replacement when the original cord is defective

• Always disconnect power at the breaker or unplug the appliance before installing
• Route the cord and secure strain relief per the appliance's original routing to prevent pinching
• Ensure the cord's connector and grounding match the appliance's inlet before connecting

This thermostat knob fits onto the control shaft so you can select and adjust cooking temperature. Replace a cracked or stripped knob to restore smooth operation and a clean, finished look.

• Attaches to the thermostat stem to allow manual temperature selection
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps when the knob spins without engaging or won't stay on the shaft
• Restores proper control feel and appearance

• Disconnect power to the appliance and allow surfaces to cool before service
• Pull the old knob straight off the thermostat shaft
• Align the new knob with the shaft and press straight on until fully seated; do not force
• The pointer aligns with the control markings before use

This is the factory glass assembly that restores a clear, intact viewing window on your appliance door. Replacing a damaged panel helps maintain safe operation and a clean, finished appearance.

• Replaces a cracked, shattered, or missing glass panel on the door
• Helps maintain proper door integrity and safe use
• Restores visibility into the cavity for monitoring cooking or baking
• Addresses rattling, loose, or sharp-edge conditions caused by broken glass

• Disconnect power and allow the unit to cool completely before servicing
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Support the door during removal; keep track of screws and trim orientation
• Reassemble in the original order; do not overtighten fasteners

This is an outer glass door used in ovens. It is the outermost part of the door on the appliance. It helps hold together the other parts of the oven so it can operate correctly. This part is made of durable materials but can crack or otherwise become damaged.Before replacing the oven outer door glass, wait for the oven to cool completely. Make sure it is unplugged and/or the gas is turned off before beginning. A set of tools and work gloves will be useful for the process. The oven frame will need to be removed to replace the part. Remove the old outer door glass and replace it with the new part before reinstalling other components.This is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as a single part. The outer door glass is made to be used with ranges, stoves, ovens, and oven/microwave combination appliances by Kenmore, Frigidaire, and Crosley.

Color: Black

The Knob is an OEM part for Frigidaire ranges. The knob attaches directly to the surface element switch and allows for easy adjustment of settings with a simple turn.

Causes of a bad range knob can be normal wear and tear over time, exposing the knob to excessive heat, or accidental damage from impact.

Symptoms of a bad range knob include:

• Loose, wobbly or difficult to turn fitment
• Cracked, broken or missing pieces
• Control functions that do not work as intended
• Inaccurate temperature readings
• Knob that falls off or does not stay securely attached

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This switch assembly restores electrical on/off control for a specific appliance function. Replace a worn or failed switch to stop intermittent operation and return reliable control to the affected circuit. What it does:

• Provides the electrical on/off or function control for the appliance circuit.
• Replaces a failed switch that can cause intermittent operation or unresponsive controls.
• Helps resolve symptoms such as a function that won't start, no response from the control, or erratic switching.
• Connects to the existing wiring harness and mates with the original mounting points.

• Disconnect power to the appliance before beginning any work.
• Remove the appropriate access panel to reach the switch; note wire and terminal locations before disconnecting.
• Unplug the wiring harness or carefully detach terminals, swap the switch assembly, then reconnect securely.
• Restore power and verify the replaced switch operates the function correctly.

For the complete terminal block kit order 12001676.

This thermostat monitors temperature in the appliance's heating circuit and opens or closes the electrical contacts to control heat and protect against overheating. Replacing a failed thermostat restores consistent heating performance and reliable safety shutoff. What it does:

• Senses temperature and cycles the heating circuit on and off to maintain target heat
• Provides over-temperature protection by opening the circuit if conditions exceed safe limits
• Helps prevent nuisance shutdowns caused by erratic temperature readings
• Common failure symptoms include no heat, inaccurate temperatures, short-cycling, or shutdown during high heat

• 1 thermostat

• Disconnect power (and gas supply if applicable) before servicing; allow all components to cool completely
• Access the thermostat per your service manual; document wire locations and transfer one at a time
• Mount the thermostat securely so the sensing surface/bulb is correctly positioned; avoid kinking or pinching any leads
• After installation, verify proper operation and temperature performance

Replacement control knob for the oven thermostat. It installs on the thermostat shaft so you can select cooking temperatures. Replaces a cracked, loose, or missing knob to restore smooth adjustment and clear, readable settings. What it does:

• Provides the hand control to turn the oven's thermostat and set temperature
• Press-fits onto the thermostat shaft for consistent, aligned operation
• Restores a secure grip and pointer alignment when the original is worn
• Common symptoms: knob cracked, falls off, spins freely, or markings are hard to read

• One white thermostat control knob

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Pull the old knob straight off the thermostat shaft—avoid prying against the panel
• Align the new knob with the shaft flat and press straight on until fully seated
• The pointer aligns with Off; remove and reseat if needed

Fits some Tappan, Frigidaire, GE, and Hotpoint models. Color: Black. Diameter: 6 1/2 inches. One round gas grate per package. For the matching drip pan order 5303131115.

This top burner spark igniter creates the spark that lights gas at the surface burner. Replacing a worn or cracked electrode restores fast, reliable ignition and helps stop burners that click but won't light.

• Generates a high-voltage spark at the burner head to ignite gas
• Common symptoms: surface burner won't light, no visible spark, intermittent ignition, or constant clicking
• Cracked ceramic, contaminated tip, or heat damage can prevent a good spark
• Direct replacement for the failed electrode on a single burner

• Disconnect power and shut off gas; allow the appliance to cool before service
• Note lead routing and bracket orientation; mount using the existing hardware per your model
• Keep the ceramic insulator clean and dry; avoid bending or touching the tip
• After installation, ensure burner base and cap are seated correctly; verify spark and ignition

Color: white. Measures about 2 inches in diameter.

Restore strong, even flame on your large burner. This sealed burner head replaces the 12K position on gas ranges/cooktops, helping recover reliable lighting and consistent heat when the original head is clogged, corroded, or damaged.

• Directs gas through calibrated ports to deliver a stable, even flame on the 12K burner position
• Helps address: burner won't light or lights intermittently; weak, uneven, or yellow flames; flame lifting or sputtering
• Replace when ports are clogged beyond cleaning, or the head is warped, cracked, or corroded
• Seats over the orifice and spark igniter in sealed-burner designs

• Disconnect power and shut off gas; allow the surface to cool completely
• Remove grate and cap; lift off or unthread the old head, retaining any mounting screw
• Clean the mating surface; align the new head over the orifice and igniter so it sits flat; if screw-retained, tighten snugly only
• Reinstall cap and grate; restore gas/power and confirm proper ignition and flame

Color: White

This cooktop grate replaces a damaged or worn grate on your gas range or cooktop. It supports pots and pans securely over the burner to maintain a stable, level cooking surface and safe, consistent heating.

• Sits above the surface burner to hold cookware at the proper height
• Provides a stable surface to reduce pan wobble, rocking, or tipping
• Replaces grates that are cracked, broken, heavily rusted, or warped
• Helps protect the cooktop from direct flame and cookware contact

• Turn all burners off and allow the cooktop and grate to cool completely before handling
• Lift off the old grate and clean debris from the support pads or recesses
• Set the new grate in place, ensuring all feet sit flat and it's centered over the burner(s)
• Check pan stability before cooking