Cub Cadet Home Maintenance Parts

The exhaust systems on lawn and garden equipment are just as important as those on a vehicle. They need a good seal to prevent a leak between the carburetor and the exhaust tube, which would allow air leakage that could cause performance issues and loud noise. Over time all exhaust gaskets deteriorate and require a full replacement. It is relatively easy to replace an exhaust gasket and requires only the use of screw drivers, a socket set or a wrench set depending on the device being service. Replacement components such as sockets or screws may also be required during this repair. The gasket surfaces should be cleaned and fully dried before being installed between the carburetor and the exhaust tube. This exhaust gasket works with Toro, Simplicity, Murray and Briggs & Stratton lawnmowers, generators, snowblowers, wood chippers, and lawn tractors. It also works with equipment made by Craftsman, Husqvarna, Cub Cadet, Poulan, Wheel Horse, MTD, Ariens, and more.

Flat washer for lawn tractors and garden equipment. Distributes load under bolt heads and prevents surface damage. Replace if worn or missing.

Replace your worn or damaged 17.9-inch 2-in-1 mower blade. This cutting blade installs on walk-behind mowers and needs replacement when dull or bent.

Replaces a cracked, hardened, or broken primer bulb on gas-powered engines. Installs on the carburetor to inject fuel for priming before starting.

A fuel tank cap assembly prevents contaminants and particles from entering the gas tank and causing problems with the carburetor or engine. The cord between the insert and the fuel cap is meant to prevent the loss of the fuel cap. However, over time the cord can wear out and break. The threads on the cap can also become worn down or swell from heat. When this occurs, consider replacing the fuel tank cap assembly. The replacement job is easy and should not need any tools, except maybe some vice grips to remove the old fuel tank cap assembly. This fuel tank cap assembly will work in conjunction with many different types of lawn and garden maintenance equipment. Most have a small engine, like lawnmowers, tillers, and log splitters. Some of this equipment is produced by the brands Craftsman, Cub Cadet, Honda, Huskee, Lawn-Boy, Mastercut, MTD, Murray, Troy-Bilt, and Yard Machines. It is a genuine OEM part.

This beige wheel cog is a genuine MTD replacement part. A wheel cog is a component of a self-propelled or push lawn mower, chipper shredder, or snow blower. This replacement part is ideal for basic maintenance for home appliances such as lawn mowers, chipper shredders, and snow blowers. These wheel cogs may be subject to damage and natural wear and tear over time. Signs of damage can include grinding or grating noises, shaking steering wheels, and uneven wear on tires that is visible to the naked eye. In cases of damage to multiple wheels on appliances, several replacement wheel cogs will need to be ordered. One will need a small flat-blade screwdriver, a socket wrench, and a dry lubricant such as graphite in order to replace a wheel cog on a lawn mower, chipper shredder, or snow blower. Always wear gloves when working with or repairing outdoor equipment. This genuine MTD wheel cog replacement works with the brands Cub Cadet, MTD, Yard Machines, Huskee, Yard-Man, and Bolens. It is an OEM authorized part manufactured in the US, fitting many MTD models.

Grass bag frame assembly for walk-behind lawn mowers. Provides structural support for the grass collection bag. Replace if cracked, bent, or broken.

Pivot arm for walk-behind lawn mowers that aids in steering and direction control. Replace if worn, damaged, or broken from heavy use or accidents.

Caster wheel bracket for walk-behind mowers. Houses and secures the front caster wheel assembly. Replace if cracked, bent, or worn to restore stability.

Hex screw for lawn mowers and outdoor power equipment. Secures components and panels. Replace if stripped, rusted, or missing for proper assembly.

Hex cap screw for securing components on lawn mowers, tractors, and outdoor power equipment. Replace if stripped, rusted, or missing hardware.

Hex screw that secures components on lawn mowers, snow throwers, tillers, and chippers. Replace if stripped, rusted, missing, or damaged during repair.

Carriage bolt fastener for lawn mowers and snow throwers. Replace if dented, cracked, punctured, or missing to secure components properly.

Replacement truss head tap screw for lawn equipment engines. Secures various engine components. Replace if missing, stripped, or damaged during maintenance.

This is a genuine replacement self-tapping hex screw with a blunt nose designed for lawn mowers and lawn tractors. It is used in a variety of locations for the engine assembly of lawn mowers. The self-tapping feature allows the metal screw threads to tightly secure to other metal. The blunt nose requires the use of a pre-drilled pilot hole smaller than the diameter of the screw. These screws do not interchange well. Be sure to check the owner's manual to ensure the correct part number. The hex head needs a socket wrench for the easiest removal and replacement. When removing this type of screw, stripped threads can occur. If this happens, use a screw of the same type in a slightly larger size to accommodate for the damage. Typically, this type of screw would need to be replaced when removed to access another part of the lawn mower for replacement, such as the carburetor. This an OEM part sourced directly from the manufacturer and is sold individually. This screw fits products by Bolens, Brute, Columbia, County Line, Craftsman, Cub Cadet, Huskee, Huskee Supreme, MTD Black, MTD Gold, Mastercut, Murray, Troy Bilt, Yard Man, & Yard Machines.

With small gasoline-powered tools that require control panels, this hex screw attaches the panel to the handles of the tools. Machined to be durable, important screws such as these take a real beating. In their locations at critical points on the handle, the hex screws are considered "wear items," and thus periodically, they must be replaced. The control panel itself is often a location of extreme forces, jostling, and abrupt movement in unpredictable directions. The constant movement, with sheet metal rubbing against the hex screws from every direction, make wear inevitable. The manufacturers recommend that spare screws of this type be kept on hand if the heavy use of the equipment is expected. Among the gasoline-powered tools that use these screws are snowblowers, yard tractors, mowers, tiller, chippers, shredders, and other tools requiring hand-maneuvered levers. These screws are compatible with a number of equipment brands and manufacturers, including MTD, Ryobi, Poulan, Yard-Man, Bolens, Troy-Bilt, and Yard Machines.