Parts for Ge DFE29JGDBBB: Dispenser Door Parts

Removes contaminants from your refrigerator's water and ice. Replace every 6 months or when the filter indicator activates. Confirm fit with your model.

The Flapper Door Spring is an OEM part for GE refrigerators. It ensures the proper operation of the ice dispenser's flapper door by providing the necessary tension for the door to open and close correctly. This helps in maintaining the internal temperature and preventing warm air from entering the freezer.

You should replace the flapper door spring if it becomes worn out or damaged. Over time, the spring can lose its tension due to constant use, become bent or broken from mishandling, or suffer from rust and corrosion.

Symptoms of a bad flapper door spring include:

• The ice dispenser flapper door not closing properly
• Warm air entering the freezer compartment
• Increased frost buildup around the ice chute
• Unusual noises when the ice dispenser is used

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Guides the center door mullion spring pivot for smooth flap operation. Replace if worn or damaged to maintain proper door seal. Verify fit with model.

Trim cap that covers the refrigerator door hinge hardware. Replace if cracked, broken, or missing to protect the hinge and restore a finished look.

Plastic clip for bottom-mount refrigerators. Secures shelves, bins, or interior components. Replace if broken, cracked, or missing to restore stability.

This small return spring provides the tension needed for a lever, latch, or flap mechanism in select refrigerators, helping the component move smoothly and snap back to its correct resting position after use.

• Restores proper tension so the linked mechanism operates smoothly and returns to neutral
• Helps doors, latches, or levers close or engage consistently
• Typical failure signs: weak or missing spring force, parts that don't spring back, poor closure, or rattling
• Replacing a fatigued spring can improve feel and reliability of the mechanism

• Disconnect power; turn off the water supply if working near dispenser or ice components
• Note spring orientation and take reference photos before removal
• Use needle-nose pliers and control stored tension to avoid injury
• Inspect related clips, pins, or brackets and replace if worn

Fix a non-responsive ice or water dispenser with this refrigerator paddle switch. Restores dispensing when the paddle is cracked or won't activate.

Replacement screw secures panels, trim, brackets, and internal components in your refrigerator. Needed when original is missing, stripped, or corroded.

This genuine replacement screw secures appliance panels and components where a short 8-18 x 1/2 in fastener is required, restoring proper fit and preventing rattles or loose parts. What it does:

• Secures panels, brackets, trim, and small components
• Restores tight fit where stripped or missing screws cause vibration or rattling
• Matches OEM thread and length for reliable fastening
• Prevents gaps that can trap dirt or interfere with operation

• One screw

• Use the correct Phillips screwdriver to avoid stripping the head
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Disconnect power and remove any panels as required before working near electrical components
• Replace only with the exact OEM screw to maintain proper fit

If your refrigerator has warm spots or uneven cooling, this air damper door assembly regulates airflow between freezer and fresh-food sections. DIY repair.

Fix ice clumping or frost buildup in your dispenser. This spring returns the ice chute door to closed position, maintaining a tight seal. Easy repair.

The Motor Duct Door is an OEM part for GE refrigerators. It is the cover that houses the evaporator fan motor and ductwork in the refrigerator. The motor and ductwork circulate cold air throughout the unit to maintain even temperatures for food storage.

Causes of a bad motor duct door can include failed seals that compromise cooling performance or damage to the door and hinges that prevent proper opening and closing. 

Symptoms of a bad motor duct door include: 

• Warm or lukewarm air inside the refrigerator sections  
• Improper airflow causes warmer or colder spots
• Difficulty opening or closing the duct door

Replacing with this genuine GE OEM part allows for optimal air circulation throughout the refrigerator. This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Ice dispenser jammed or spilling cubes? This ice funnel guides ice from maker to bin. Moderate DIY repair; requires dispenser panel removal.

Replacement fastener for refrigerator door handles. Secures handle to door with durable metal construction. Needed when original is cracked or broken.

The Set Screw is an OEM part for GE refrigerators. The set screw fits into the handle assembly, ensuring a tight and stable connection to the refrigerator door. This set screw is essential for preventing the door handle from becoming loose or coming off, which can affect the ease of opening and closing the refrigerator door. 

Causes of a malfunctioning Set Screw can vary. Normal wear and tear is a common issue, causing the screw to strip or loosen over time. Incorrect installation is another factor.  

Symptoms of a bad Set Screw include:

• A loose refrigerator door handle, which may wobble or detach partially from the door.
• Difficulty in opening or closing the refrigerator door due to a lack of secure grip.
• The need to frequently retighten the door handle.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Top-left refrigerator door bin for models with in-door ice. Replaces cracked, broken, or missing bins to restore secure storage and organization.

Detachable ice storage bin with hinged door for refrigerator ice dispensers. Replace if cracked, broken, or missing to restore ice containment and access.

Refrigerator collar gasket seals connections to prevent air leaks and maintain temperature. Replace if worn, cracked, or causing cooling issues.

Injection molded door retainer for refrigerator door assembly. Replaces cracked, broken, or missing retainers that secure door components in place.

Fix water leaking from your refrigerator dispenser with a new port gasket. This seal prevents drips and moisture around the dispenser opening.

Replacement arc-style door handle assembly for refrigerator fresh food or freezer doors. Restores secure grip when original handle is cracked or broken.

A left-hand closure door assembly that replaces a worn or broken door closure to restore proper sealing and smooth drawer/door operation. Helps stop drafts and keeps compartments closing correctly for reliable performance. What it does

• Guides and supports the left-side door/drawer as it closes to ensure proper alignment.
• Helps form a tight seal to reduce air leakage and maintain interior temperature.
• Prevents rattling or catching that can occur when the closure is damaged or worn.
• Commonly replaced when the door doesn't stay closed, binds, or leaves a visible gap.

• Disconnect power to the appliance before starting any repair.
• Basic hand tools are typically required; access may involve removing a drawer or trim panel.
• Handle parts carefully to avoid damaging surrounding panels or gaskets.

Fixes dim or uneven refrigerator lighting. This LED light shield replaces cracked or yellowed covers to restore proper light distribution. Simple DIY fix.

8-18 hi/lo 5/8

This is a replacement 8-18 x 1/2" flat-head slotted screw commonly used to secure appliance panels and components. It restores proper fastening and helps eliminate rattles, loose trim, or misaligned parts. What it does:

• Secures panels, brackets, and trim to restore proper fit
• Stops vibration-related noise caused by loose fasteners
• Replaces missing or stripped screws to prevent parts from shifting
• Works where a flat-head, slotted-drive #8 screw with 1/2" length is required

• One 8-18 x 1/2" flat-head slotted screw

• Use the correct size slotted screwdriver to avoid cam-out or head damage
• Tighten until snug; avoid over-torquing which can strip threads or deform panels
• Replace any stripped mating hardware for secure fastening
• Disconnect power before doing repairs on appliances where required for safety

This spring tray latch secures a removable tray so it stays seated during normal use, helping maintain proper alignment and function. Replace a worn or broken latch to stop trays from slipping or failing to stay closed. What it does

• Holds the tray in the correct closed position so it does not slide out unintentionally.
• Restores proper engagement when a tray won't stay latched or shifts during use.
• Helps prevent spills and maintains correct component alignment.
• Works as the spring/retention element for the tray latch assembly.

• High-level fit: installs in the tray latch area; part matches your existing latch before installing.
• Use basic hand tools; keep small parts and springs secure during replacement.
• Disconnect power to the appliance if working near electrical components or moving mechanisms.
• If the tray or adjacent parts are damaged, replace them as well to ensure proper function.

Ice dispenser not working or jamming? This ice bucket and auger motor assembly restores proper ice storage and dispensing. Moderate DIY repair.

Ice dispenser not working or jamming? This clutch spring restores proper tension so the auger engages smoothly. Simple DIY fix for reliable dispensing.

This clutch coupling connects the washer motor/clutch to the agitator so the tub agitates properly during the wash cycle. Replaces a worn or broken coupling to restore normal agitation and reduce slipping or grinding. What it does:

• Transfers motor/clutch rotation to the agitator so clothes move during wash cycles.
• Commonly used when the washer spins but does not agitate or when agitation is weak.
• Helps eliminate slipping, grinding, or unusual noise from a failing coupling.
• Works as the mechanical link between the drive system and agitator assembly.

• One clutch coupling as pictured and specified by the OEM.

• Disconnect power and water supply before starting any repair.
• Basic mechanical skills and common hand tools required; follow OEM disassembly steps for safe access.
• Inspect related parts (agitator, drive shaft, clutch) for wear and replace as needed.

Loose or rattling parts inside your refrigerator? This e-clip retaining ring secures shafts and pins to prevent unwanted movement and component separation.

Folding center strip that seals the gap between French doors. Replace if worn, damaged, or causing air leaks and condensation. Verify fit by model number.

Center mullion hinge for bottom-mount refrigerators. Mounts between refrigerator and freezer doors to support door alignment and closing. Replace if cracked or broken.

Refrigerator mullion hinge allows the center flipper rail between doors to pivot smoothly. Replace if doors don't seal, mullion is loose, or condensation forms. Confirm fit by model number.

Redirects refrigerator tubing at a right angle for neater routing in tight spaces. Replace this 5/16 in. connector if cracked, leaking, or broken.

Controls refrigerator display, buttons, and dispenser functions. Replace if display is dark, buttons unresponsive, or dispenser malfunctions. Verify fit.

The Refrigerator door board profile is an OEM replacement part for GE refrigerator doors. It is the electronics responsible for operating door functions like illumination, alarm systems, temperature displays, and sealed system sensors.

Causes of a bad control board can include moisture penetration corroding circuits over time, cracks or breaks from impact, or malfunctions in electronic components.

Symptoms of a bad control board include:

• Lights or displays failing to illuminate as intended
• Inability to adjust the temperature or access diagnostic controls
• Alarms or audio components malfunctioning
• Disruptions to the refrigeration cycle from sensor faults

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Round-head sheet metal screw (10-24 x 5/8) secures trim, panels, and internal components in refrigerators. Replace if missing, stripped, or corroded.

Hinge-mounted stop that limits how far your refrigerator door can swing open. Replace if cracked, broken, or missing to prevent door overextension.

Fixes intermittent operation or no power to components. This 1/4" clip connector secures wire terminals for reliable electrical connections in your fridge.