Parts for Ge DFE29JSDBSS: Dispenser Door Parts

Removes contaminants from your refrigerator's water and ice. Replace every 6 months or when the filter indicator activates. Confirm fit with your model.

The Flapper Door Spring is an OEM part for GE refrigerators. It ensures the proper operation of the ice dispenser's flapper door by providing the necessary tension for the door to open and close correctly. This helps in maintaining the internal tem

Guides the center door mullion spring pivot for smooth flap operation. Replace if worn or damaged to maintain proper door seal. Verify fit with model.

Trim cap that covers the refrigerator door hinge hardware. Replace if cracked, broken, or missing to protect the hinge and restore a finished look.

Replacement round-head screw for refrigerators. Secures interior panels, brackets, and components. Needed when original fasteners are missing or worn.

This LED jumper harness connects LED lights and lighting assemblies to the fridge's wiring, restoring reliable power and signal to LED circuits. It's a direct-replacement wiring jumper for lighting systems that need a damaged or worn harness replaced. What it does:

• Transfers power and signal between LED modules and the appliance wiring harness
• Replaces damaged, frayed, or corroded jumper wiring that can cause flickering or loss of light
• Helps restore consistent interior or dispenser lighting when the LED circuit is interrupted
• Maintains OEM routing for correct fit and connector alignment

• Disconnect power to the appliance before starting any repair to avoid electric shock.
• Handle connectors carefully; align and seat plugs fully but avoid excessive force.
• Route the harness away from sharp edges, hinges, and moving parts; secure with existing clips or ties.

Plastic clip for bottom-mount refrigerators. Secures shelves, bins, or interior components. Replace if broken, cracked, or missing to restore stability.

The Refrigerator Display Assembly is an OEM replacement part for GE refrigerators. It is the user interface component that displays important information, such as temperature settings, operational modes, and any error codes or notifications. NOTE: Cont

This small return spring provides the tension needed for a lever, latch, or flap mechanism in select refrigerators, helping the component move smoothly and snap back to its correct resting position after use.

• Restores proper tension so the linke

Replace the dispenser actuator paddle on your refrigerator when it becomes cracked, broken, stuck, or won't release properly. Installs at the front.

Replacement screw secures panels, trim, brackets, and internal components in your refrigerator. Needed when original is missing, stripped, or corroded.

This genuine replacement screw secures appliance panels and components where a short 8-18 x 1/2 in fastener is required, restoring proper fit and preventing rattles or loose parts. What it does:

• Secures panels, brackets, trim, and small components
• Restores tight fit where stripped or missing screws cause vibration or rattling
• Matches OEM thread and length for reliable fastening
• Prevents gaps that can trap dirt or interfere with operation

• One screw

• Use the correct Phillips screwdriver to avoid stripping the head
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Disconnect power and remove any panels as required before working near electrical components
• Replace only with the exact OEM screw to maintain proper fit

If your refrigerator has warm spots or uneven cooling, this air damper door assembly regulates airflow between freezer and fresh-food sections. DIY repair.

Fix ice clumping or frost buildup in your dispenser. This spring returns the ice chute door to closed position, maintaining a tight seal. Easy repair.

The Motor Duct Door is an OEM part for GE refrigerators. It is the cover that houses the evaporator fan motor and ductwork in the refrigerator. The motor and ductwork circulate cold air throughout the unit to maintain even temperatures for food storage

Ice dispenser jammed or spilling cubes? This ice funnel guides ice from maker to bin. Moderate DIY repair; requires dispenser panel removal.

Replacement fastener for refrigerator door handles. Secures handle to door with durable metal construction. Needed when original is cracked or broken.

The Set Screw is an OEM part for GE refrigerators. The set screw fits into the handle assembly, ensuring a tight and stable connection to the refrigerator door. This set screw is essential for preventing the door handle from becoming loose or coming of

Top-left refrigerator door bin for models with in-door ice. Replaces cracked, broken, or missing bins to restore secure storage and organization.

Detachable ice storage bin with hinged door for refrigerator ice dispensers. Replace if cracked, broken, or missing to restore ice containment and access.

Control board exposed or damaged? This PCB cover assembly shields electronics from dust and moisture, restoring protection for reliable operation.

Refrigerator collar gasket seals connections to prevent air leaks and maintain temperature. Replace if worn, cracked, or causing cooling issues.

Fix water leaking from your refrigerator dispenser with a new port gasket. This seal prevents drips and moisture around the dispenser opening.

Seals the refrigerator compartment to keep cold air in. Replace when worn to prevent frost buildup, condensation, and temperature issues. Verify fit.

A left-hand closure door assembly that replaces a worn or broken door closure to restore proper sealing and smooth drawer/door operation. Helps stop drafts and keeps compartments closing correctly for reliable performance. What it does

• Guides an

Fixes dim or uneven refrigerator lighting. This LED light shield replaces cracked or yellowed covers to restore proper light distribution. Simple DIY fix.

8-18 hi/lo 5/8

This is a replacement 8-18 x 1/2" flat-head slotted screw commonly used to secure appliance panels and components. It restores proper fastening and helps eliminate rattles, loose trim, or misaligned parts. What it does:

• Secures panels, brackets, and trim to restore proper fit
• Stops vibration-related noise caused by loose fasteners
• Replaces missing or stripped screws to prevent parts from shifting
• Works where a flat-head, slotted-drive #8 screw with 1/2" length is required

• One 8-18 x 1/2" flat-head slotted screw

• Use the correct size slotted screwdriver to avoid cam-out or head damage
• Tighten until snug; avoid over-torquing which can strip threads or deform panels
• Replace any stripped mating hardware for secure fastening
• Disconnect power before doing repairs on appliances where required for safety

This spring tray latch secures a removable tray so it stays seated during normal use, helping maintain proper alignment and function. Replace a worn or broken latch to stop trays from slipping or failing to stay closed. What it does

• Holds the tray in the correct closed position so it does not slide out unintentionally.
• Restores proper engagement when a tray won't stay latched or shifts during use.
• Helps prevent spills and maintains correct component alignment.
• Works as the spring/retention element for the tray latch assembly.

• High-level fit: installs in the tray latch area; part matches your existing latch before installing.
• Use basic hand tools; keep small parts and springs secure during replacement.
• Disconnect power to the appliance if working near electrical components or moving mechanisms.
• If the tray or adjacent parts are damaged, replace them as well to ensure proper function.

Ice dispenser not working or jamming? This ice bucket and auger motor assembly restores proper ice storage and dispensing. Moderate DIY repair.

Ice dispenser not working or jamming? This clutch spring restores proper tension so the auger engages smoothly. Simple DIY fix for reliable dispensing.

Ice dispenser not working or jamming? This ice bucket and auger motor assembly restores proper ice storage and dispensing. Moderate DIY repair.

This clutch coupling connects the washer motor/clutch to the agitator so the tub agitates properly during the wash cycle. Replaces a worn or broken coupling to restore normal agitation and reduce slipping or grinding. What it does:

• Transfers mot

Loose or rattling parts inside your refrigerator? This e-clip retaining ring secures shafts and pins to prevent unwanted movement and component separation.

Folding center strip that seals the gap between French doors. Replace if worn, damaged, or causing air leaks and condensation. Verify fit by model number.

Center mullion hinge for bottom-mount refrigerators. Mounts between refrigerator and freezer doors to support door alignment and closing. Replace if cracked or broken.

Refrigerator mullion hinge allows the center flipper rail between doors to pivot smoothly. Replace if doors don't seal, mullion is loose, or condensation forms. Confirm fit by model number.

Redirects refrigerator tubing at a right angle for neater routing in tight spaces. Replace this 5/16 in. connector if cracked, leaking, or broken.

If your water line is leaking or disconnected, this coupler connects tubing in your refrigerator. Simple push-in design for DIY repair in under 15 minutes.

Controls refrigerator display, buttons, and dispenser functions. Replace if display is dark, buttons unresponsive, or dispenser malfunctions. Verify fit.

The Refrigerator door board profile is an OEM replacement part for GE refrigerator doors. It is the electronics responsible for operating door functions like illumination, alarm systems, temperature displays, and sealed system sensors.

Round-head sheet metal screw (10-24 x 5/8) secures trim, panels, and internal components in refrigerators. Replace if missing, stripped, or corroded.

Hinge-mounted stop that limits how far your refrigerator door can swing open. Replace if cracked, broken, or missing to prevent door overextension.

Fixes intermittent operation or no power to components. This 1/4" clip connector secures wire terminals for reliable electrical connections in your fridge.