Parts for Kitchenaid KDTE204ESS4: 02 - Door And Panel Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Replace a cracked, bent, or worn right-hand door hinge on your dishwasher. Restores proper door alignment and smooth opening/closing operation.

Foam pad that installs between dishwasher door panels to dampen sound and shield from heat. Replace if torn, compressed, or missing for quieter operation.

Color: White

Covers the lower front of your dishwasher for a finished look. Replace if cracked, broken, missing, or damaged from impact or wear and tear.

Color: White

Black control panel for dishwashers. Replaces cracked, broken, or faded panels on the front of your dishwasher. Restores the exterior appearance.

Stainless steel outer door panel for dishwashers. Replaces cracked, dented, or discolored panels. Updates the exterior appearance of your unit.

This factory screw secures components in your appliance to keep them properly mounted and stable during operation. Replacing a missing or damaged screw restores a tight fit and helps prevent vibration, noise, or loosening parts.

• Fastens panels, brackets, or trim to maintain correct alignment
• Can address rattling, vibration, or loose/misaligned parts where this screw is used
• Helps prevent wear from movement caused by missing or stripped hardware

• Unplug power and shut off utilities before service
• Note original screw location and orientation; replace like-for-like
• Do not overtighten—start by hand to avoid cross-threading
• Address threads before installing the new screw

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Reduce noise and prevent heat loss with this dishwasher toe panel insulation. Replace when soiled, damaged, or missing. Adhesive-backed for easy install.

This stud is a small mounting fastener that provides a secure anchor point for attaching appliance components. Replacing a worn or missing stud restores a tight, aligned fit and helps prevent looseness, rattles, or shifting.

• Provides a fixed, threaded anchor for mounting a handle, bracket, or panel
• Helps keep parts aligned and secure during normal operation
• Common replacement for studs that are stripped, bent, broken, or missing
• Symptoms can include a loose or wobbly component, difficulty tightening, or visible damage/corrosion

• Disconnect power and, if applicable, shut off water or gas before servicing
• Wear cut-resistant gloves and handle panels carefully
• Hand-start threads to avoid cross-threading; tighten snugly without over-torquing
• Reinstall any covers or related hardware in their original positions

White retainer clip secures the kickplate at the bottom of your dishwasher. Replace if broken, cracked, missing, or lost to keep kickplate firmly attached.

Color: Black

The Access Panel Retaining Clip is an OEM part for Whirlpool dishwashers. This black clip is used to secure the access panel to the dishwasher frame, ensuring it stays in place and provides a finished look while protecting internal components.

You should replace the access panel retaining clip if it becomes damaged or worn out. Over time, the clip can break or lose its grip due to repeated removal and installation of the access panel or general wear and tear.

Symptoms of a bad access panel retaining clip include:

• The access panel not staying securely attached
• Rattling or vibrations from a loose panel
• Missing or broken clips

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Replacement fastening nut for dishwasher components and mounting hardware. Secures threaded shafts, studs, or bolts. Needed when original is stripped, missing, or corroded.

10-32 thread machine screw secures panels, brackets, and internal components. Replace missing, stripped, or damaged fasteners to restore solid fit.

The Nameplate is an OEM part for Whirlpool appliances. It serves as an identification label, typically displaying the brand name and model number, providing a clean and professional appearance for the appliance.

You should replace this nameplate if it becomes damaged or worn out. Common causes of a bad nameplate include wear and tear from regular cleaning, exposure to moisture or heat that can cause peeling or fading, and accidental impact that can lead to cracks or detachment.

Symptoms of a bad nameplate include:

• Fading or illegible text
• Peeling or detaching from the appliance surface
• Visible cracks or damage
• The nameplatae being completely missing

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.