Parts for Whirlpool RF366PXDN0: 03 - Door And Drawer Parts

Size: 8 x 3/8 inch.

This part has been discontinued and is no longer available.

This replacement oven door glass restores a clear viewing window and proper heat retention. Replace this pane when the glass is cracked, shattered, or permanently stained to keep your oven safe, efficient, and easy to monitor.

• Forms the inner or outer window of the oven door, sealing heat while letting you watch cooking progress
• Helps maintain temperature stability and preheat performance
• Common failure signs: visible cracks or chips, shattered glass, fogging or residue between panes, or difficulty maintaining temperature
• Restores safety by eliminating sharp edges and reducing risk of further breakage

• Disconnect power and allow the oven to cool completely; shut off gas supply if applicable
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Remove the door and glass retainers; note screw and trim orientation
• Transfer any clips/trim from the original pane as needed; reassemble without overtightening and confirm door alignment and seal

Size: 8 x 3/8 inch.

This replacement screw secures appliance panels, brackets, and internal components so your unit stays assembled, aligned, and quiet. Use it to replace missing, stripped, or corroded hardware and restore a reliable factory-fastened connection.

• Fastens panels, brackets, or trim to the cabinet/frame
• Helps maintain proper alignment of doors, controls, or covers
• Replaces hardware that's missing, rusted, or with a stripped head
• Can help reduce vibration or rattling from loose fasteners

• Disconnect power and shut off gas/water supplies before service
• Match thread and length to the original; transfer any washers if present
• Start threads by hand to avoid cross-threading, then tighten with the correct driver
• Do not overtighten; snug until secure to prevent damage to plastic or sheet metal

A small replacement mounting clip that secures the appliance handle to the door or control panel for a firm fit and reliable operation. Replaces a worn or broken clip to restore handle stability and reduce movement. What it does:

• Holds the handle tight to the door or panel so the handle doesn't wobble or come loose
• Prevents the handle from detaching during normal use
• Helps stop rattling or shifting that can occur with a broken clip
• Fits into the handle mounting location to align and lock the handle in place

• One mounting handle clip

• Disconnect power (and water if applicable) before beginning any repair
• Access may require removing the door trim or interior panel—keep track of fasteners
• Use appropriate hand tools and avoid forcing plastic clips to prevent breakage

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening