Parts for Electrolux FGVU17F8QFA: 02 - Door Parts

This replacement gasket restores a tight seal between mating parts, helping prevent leaks and ensuring your appliance performs as designed. What it does:

• Creates a reliable seal between components to keep air, water, or heat from escaping
• Helps maintain proper operating performance and efficiency
• Replace if the original is cracked, torn, flattened, or no longer sealing
• Common symptoms include moisture or drips at the joint, drafts, or visible gasket damage

• 1 gasket

• Disconnect power and shut off water or gas supply before servicing
• Compare the new gasket to the old one to confirm orientation and routing
• Clean and dry all mating surfaces; remove old residue before installing
• Seat the gasket evenly without stretching; verify uniform contact after reassembly

The Freezer Door Key is an OEM replacement part for Frigidaire refrigerators. This small but essential component is designed to securely lock the freezer door, preventing accidental openings or unauthorized access.

Symptoms of needing to replace the freezer door key include:

• Difficulty in locking or unlocking the freezer door
• The key not fitting properly or becoming stuck in the lock
• Visible wear, damage, or breakage of the key itself

Causes of a faulty freezer door key can include normal wear and tear over time, physical damage due to impact or mishandling, or issues with the locking mechanism itself.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

This main electronic control board manages the appliance's user interface and core functions, restoring responsive controls and proper cycle behavior when the original board fails. It replaces a faulty control to help return normal operation. What it does:

• Receives user commands from the console and sends control signals to the appliance's components.
• Regulates timed cycles, motor and heater operation, and routine sequencing to enable normal function.
• Drives the display and indicator lights so status and settings appear correctly.
• Can stop or prevent operation if internal faults occur, which may show as error codes or no-response symptoms.

• Always disconnect power (unplug or switch off breaker) before attempting service.
• Handle the board by its edges and avoid touching components; discharge static by grounding yourself.
• Verify model-specific wiring and mounting in the service manual or OEM parts diagram before installation.

This replacement nameplate label restores the appliance's identification and rating information so you can read model, serial, and electrical data clearly. Helps when the original label is faded, damaged, or missing. What it does

• Displays model and serial numbers, electrical ratings and safety markings for identification and service
• Replaces faded, torn, or illegible factory labels so appliance data is readable
• Helps technicians and owners confirm correct specifications during repairs or replacement parts ordering
• Does not affect appliance operation; used for identification and information only

• One replacement nameplate label

• Clean and dry the surface before applying so the label adheres and lays flat
• Align carefully; many labels are adhesive-backed and are intended for single use
• Avoid placing over gaskets, vents, or moving parts; install where original label was located

This door stop controls the door's swing, preventing it from opening past its designed angle and protecting the hinge and cabinet. Replace a cracked or missing stop to restore controlled door movement and help maintain proper alignment and sealing.

• Limits door opening angle to prevent overextension
• Helps protect hinges and prevent cabinet/wall impact
• Supports consistent door alignment and gasket contact
• Typical signs: door swings too far, visible broken/missing stop, scuffing near hinge area

• Disconnect power and support or unload the door to reduce weight before servicing
• Support the door; remove hinge cover/hardware as required by your model
• Note the original stop's orientation; transfer and secure with existing hardware
• Adjust hinges if needed

This replacement door handle restores a sturdy, comfortable grip on your refrigerator door. It replaces cracked or loose handles so you can open and close the door safely while keeping the appliance's appearance clean and finished.

• Provides the leverage and grip needed to open and close the door
• Restores appearance when the original handle is worn, discolored, or broken
• Helps prevent stress on the door gasket by giving a proper grab point
• Common signs of failure: handle is cracked, loose, wobbly, or missing

• Disconnect power before servicing; turn off water supply if working near a dispenser line
• Open the door and remove any decorative end caps to access the mounting screws
• Support the handle, remove screws, position the new handle, and reinstall using existing hardware; do not overtighten
• The handle is secure and the door opens and closes smoothly

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This door closing ramp provides the angled surface a hinge cam or glide rides on so the door opens smoothly and pulls itself shut. Replacing a worn ramp restores proper alignment and consistent, reliable closure. What it does

• Creates the sloped track for the mating hinge cam/glide
• Helps the door self-close and seal correctly
• Reduces friction, grinding, or clicking at the hinge area
• Common symptoms: door won't stay closed, pops open, sags, or makes noise when opening/closing

• Includes 1 ramp

• Disconnect power and remove items from the door before service
• Support the door; remove hinge hardware as needed to access the ramp
• Note the ramp's orientation and reuse original fasteners
• After installation, verify door alignment and gasket seal

A small replacement mounting clip that secures interior trim or panels on select refrigerators, helping restore a snug fit and reduce loose, rattling parts. Fits where worn or broken clips allow trim to shift. What it does:

• Holds trim, panels or small components in place to prevent rattling and movement.
• Restores proper alignment of affected panels so edges sit flush and look finished.
• Simple mechanical fastening — replaces brittle or broken clips that no longer grip.
• Helps reduce noise caused by loose interior parts during normal operation.

• Always unplug the appliance or switch off power at the breaker before servicing.
• Remove the affected trim or panel per manufacturer instructions to access the clip location.
• Press the clip into the mating slot or post until it seats securely; use a small tool if needed to avoid fingernail or surface damage.
• Inspect surrounding mounting surfaces for cracks or wear; damaged supports may require additional replacement parts.

This door shelf bin attaches to the inner door panel to hold bottles, jars, and small items. Replacing a cracked or missing bin restores secure, organized storage and helps prevent items from tipping or falling during use.

• Provides on-door storage for jars, condiments, and similar items
• Snaps into the door liner to keep items in place during opening/closing
• Replace if cracked, warped, or if end tabs are broken and the bin won't stay seated
• Symptoms include reduced door storage, items falling, or the bin popping loose

• Disconnect power before servicing
• Remove contents, then lift the old bin up and out of the door liner retainers
• Align the new bin with the slots and press down until it locks fully in place
• Distribute weight evenly and avoid overloading to prevent future damage

The Door Bin is an OEM replacement part for Frigidaire refrigerators. It is an internal door that controls access to the bin storage compartment. This bin area provides additional shelving and can be used to neatly organize larger refrigerated items. This shelf measures approximately 14.25 x 6 inches.

Causes of a bad door bin can include damage to the hinges from frequent opening and closing or impact from heavy items, issues with the door latch or magnets not securely holding the door in closed position.

Symptoms of a bad bin include:

• The door not closing or latching properly
• Gaps allow cool air to escape from the storage area
• Difficulty accessing items inside the storage bin
• Lean or sag over time due to compromised hinges

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Door Shelf Bin is an OEM part for Frigidaire refrigerators. It provides storage for commonly used items along the inside of the refrigerator door.

Symptoms of a bad door shelf bin include:

• Cracks or fractures developing in the plastic
• Difficulty removing or replacing bin due to loose brackets  
• Items falling through or wedging into bin openings
• Missing brackets rendering the bin unusable

Causes of a bad door shelf bin can be normal wear over extended use periods, damage from overloading or dropping heavy items, or stresses from repeated door closings.

Replacing with this OEM bin restores useful door storage space. Compatible with existing mounting locations, it supports organization within busy kitchens.  

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace to avoid further breakdowns.
 

Note: Quantity is one plug button.

This part number contains one (1) screw.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

This nut-anchor is a small mounting insert that provides a secure threaded point in thin sheet metal so screws can fasten panels or components reliably. It restores a solid attachment where the original fastener or threaded hole is missing. What it does:

• Provides a reinforced threaded anchor in thin metal or plastic panels
• Allows screws to tighten without stripping the sheet material
• Stops panels, trim, or assemblies from coming loose or rattling
• Used where a captive nut or threaded insert is required for reassembly

• Install where original nut/insert was located; verify orientation before fastening
• Use the correct screw size and hand-tighten to avoid overtightening or thread damage
• Disconnect power and move the appliance to a safe, stable work area before servicing
• If the original mounting point is severely damaged, consider assessing the surrounding structure for repair

The Refrigerator Door Gasket Clips are OEM parts for Frigidaire refrigerators. These clips secure the door gasket in place, ensuring a tight seal to maintain the internal temperature and prevent cold air from escaping. This pack contains 40 clips, which secure the interior trim pieces and hold the gasket and liner to the freezer lid.

Over time, the gasket clips can become damaged or worn out due to frequent opening and closing of the refrigerator door, exposure to moisture, or accidental impacts. If the clips fail, the door gasket may not stay in place, compromising the refrigerator's efficiency.

Symptoms of bad refrigerator door gasket clips include:

• The door gasket not staying securely in place
• Visible damage or wear on the clips
• Cold air escaping from around the door
• Increased energy consumption due to poor sealing

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.