Parts for Frigidaire FFTR1814TS3: Door Parts

The Freezer Door Gasket is an OEM part for Frigidaire refrigerators, specifically designed to create an airtight seal around the freezer door. This gasket prevents warm air from entering and cold air from escaping the freezer compartment, ensuring efficient cooling and energy efficiency. Made from durable rubber, this gasket is flexible yet strong, designed to withstand the constant opening and closing of the freezer door.  

Causes of a bad Freezer Door Gasket can include wear and tear over time, exposure to excessive moisture leading to mold or mildew buildup, or damage from cleaning products or sharp objects. 

Symptoms of a bad Freezer Door Gasket include:

• Visible cracks, tears, or warping in the gasket.
• Condensation or ice buildup around the door edges.
• The freezer struggles to maintain the set temperature.
• Increased energy consumption as the freezer works harder to keep cold.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This freezer door gasket is an OEM replacement part for Frigidaire refrigerators. The gasket measures approximately 28" wide x 18" long. This gasket is a perfect fit for your refrigerator's inner door panel.

Symptoms of a bad freezer door gasket include:

• Difficulty keeping interior cold temperatures below 0°F  
• Frost buildup around top and sides of door seals
• Defrosts required increasing in frequency
• Visible air gaps noticeable along gasket perimeter

Causes of a bad freezer door gasket can include material breakdown due to hundreds of door opening and closing compression cycles over time developing small cracks in the rubber. Spills along bottom edges may promote seal deterioration if not cleaned promptly.

This genuine Frigidaire replacement gasket is compatible with other brands such as Electrolux and Kenmore as well 

NOTE: To achieve a smooth installation, simply soak the gasket in warm water or use a hair dryer on low heat to eliminate any folds or creases.

Replaces a worn refrigerator door seal on the fresh-food compartment to restore a tight, even seal. Helps maintain cold temperatures, reduce condensation around the door, and cut energy loss when the old gasket is torn, warped, or gapped.

What it does

• Creates a continuous seal around the fresh-food door to keep cold air in.
• Helps prevent warm-air leaks that cause temperature swings.
• Reduces moisture/sweating along the door edge.
• Addresses gaps, tears, cracks, or a gasket that won’t lie flat.

What’s included
One refrigerator door gasket for the fresh-food door (black).

Install notes

• Unplug the refrigerator before starting.
• Warm the new gasket (soak in warm water or use low-heat hair dryer) to relax folds.
• Seat the gasket lip fully into the door channel—start at the corners and work around.
• Close the door and check for uniform contact (paper-pull test); level/adjust hinges as needed and allow 24 hours for the gasket to conform.

The Refrigerator Door Gasket is an OEM replacement part for Frigidaire refrigerators. This crucial component is responsible for creating an airtight seal around the refrigerator door, ensuring efficient temperature control and energy conservation. This gasket is "approximately" 28” by 41”, and may require a screwdriver to remove the old gasket.

Symptoms of needing to replace the refrigerator door gasket include:

• Difficulty in closing the refrigerator door properly
• Visible gaps or gaps around the door gasket area
• Condensation buildup or frost formation around the door gasket
• Increased energy consumption due to inefficient sealing

Causes of a faulty door gasket can include normal wear and tear over time, exposure to extreme temperatures or UV light, or physical damage due to impact or mishandling.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

The Door Shelf is an OEM replacement part for Frigidaire refrigerators. This gallon door shelf measures about 23 inches wide from inside to inside. 

Causes of a bad door shelf can include frequent use, overloading, or accidental impacts, leading to cracks, breaks, or warping. When the door shelf is damaged, it can compromise the stability and security of stored items, making it less effective for storage needs.

Symptoms of a bad part may include- 

• Cracks or breaks in the plastic
• Difficulty holding items securely in place 
• Shelf not staying attached to the door 
• Difficulty closing the door

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Refrigerator Door Shelf is an OEM replacement part for Frigidaire refrigerators that provides storage space on the refrigerator door. This shelf is designed to fit securely on the door, offering a convenient place to store condiments, bottles, and other items for easy access. The package includes one door shelf. The shelf measures approximately 23”.

Over time, the shelf can crack or break due to frequent use, overloading, or accidental impacts. A faulty door shelf can result in items falling or not being securely held in place.

Symptoms of a bad part include:

• Sagging or broken shelves
• Items falling off the shelf
• Difficulty in opening or closing the refrigerator door

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Dairy Door is an OEM replacement part for  Frigidaire side-by-side refrigerators. Located inside the fresh food compartment, it provides a dedicated storage area for milk, yogurt, cheese and other dairy products requiring colder temperatures. The door measures approximately 9 inches wide and 5 inches high.

Causes of a bad dairy door include normal wear from repeated opening and closing over time. Exposure to spills inside the refrigerator can also potentially damage door shelf components or seals.

Symptoms of a bad dairy door are: 

• Difficulty opening or closing the door smoothly  
• Door alignment issues where it does not sit flush in the frame
• Leaks or moisture inside the dairy storage area
• Damage or cracks in shelf supports or gasket seals

This OEM part is also compatible with models from brands like Electrolux, Gibson, and Kelvinator brand models.

NOTE: For white use 240337701

The Freezer Door Shelf is an OEM part for Frigidaire side-by-side refrigerators. It provides adjustable storage within the freezer compartment for easy access to items. The shelf measures about 24 inches long and 5 inches wide.

Causes of a bad freezer door shelf can include wear over time from repeated loading/unloading that causes scratches or cracks in the lightweight plastic. Exposure to slushy spills may promote material breakdown if not cleaned promptly. 

Symptoms of a bad freezer door shelf include:

• Sagging or inability to bear weight of frozen packages
• Breakage leaving smaller pieces that could fall  
• Discoloration compromising appearance and sanitation
• Shelving that won't stay level or properly positioned

This genuine Frigidaire shelf is also compatible with Electrolux and Kenmore models.

This small black plug/button covers a hinge or bearing access hole to restore a finished appearance and help keep out dirt and debris. It's a simple, inexpensive trim piece that maintains the appliance's look and helps protect internal components. What it does:

• Covers exposed hinge or bearing access holes for a clean, finished appearance
• Helps keep dust and debris out of hinge or bearing cavities
• Prevents snagging and reduces the chance of small items entering the opening
• Matches factory appearance and fit for a seamless repair

• Push-fit design; press into the hole until fully seated
• Keep away from small children — small part is a choking hazard

This plug button is a small control panel push button used on select Frigidaire appliances to replace a worn or broken button and restore normal user control. It snaps into the panel for a clean, factory-fit appearance. What it does:

• Acts as the tactile push button used to operate a specific control or function on the appliance
• Replaces cracked, loose, or missing buttons that prevent consistent button actuation
• Restores proper contact engagement so the control registers presses reliably
• Helps eliminate cosmetic damage and keeps the control surface sealed against debris

• One plug button

• Snap-in replacement; remove power to the appliance before attempting any service
• If button is attached to an electronics assembly, handle boards and connectors carefully to avoid damage
• Use basic hand tools as needed and avoid forcing parts—verify orientation before snapping into place

Color: White. Used to cover the hinge bearing hole.

Color: White

This replacement name plate is the identification label used on the appliance's exterior to restore a clear, readable ID and finish. It helps keep the appliance looking complete and makes model/serial information visible. What it does:

• Replaces a worn, faded, or missing identification label on the appliance exterior
• Restores the appliance's original appearance and readable markings
• Helps owners locate model/serial details when present on the label
• Prevents confusion caused by missing or damaged name plate graphics

• High-level replacement; clean and dry the mounting surface before installing for best adhesion
• Remove any old adhesive or backing carefully to avoid surface damage
• Align the label precisely, then press firmly to secure
• Disconnect power and follow basic safety precautions when removing exterior panels if required

This door stop limits the opening range of your refrigerator door to prevent overextension and hinge strain. Replace a worn or broken stop to restore controlled door movement and protect surrounding cabinetry from accidental impacts. What it does:

• Controls how far the door opens to prevent overextension and damage
• Helps maintain proper door alignment and reduces stress on the hinges
• Replaces cracked, deformed, or missing stops that no longer hold the door at its stop point
• Common symptoms include the door swinging too far, a hard "clunk" at full open, or visible damage to the stop

• 1 door stop

• Disconnect power; turn off water supply if your unit has a dispenser/ice maker
• Support the door before loosening any hinge fasteners to access the stop
• Note the stop's orientation and position; transfer any spacers and reinstall the same way
• Open and close the door to verify proper range and clearance before fully tightening fasteners

This door stop limits the refrigerator door's opening range to protect hinges and nearby cabinets. Replace a cracked or missing stop to restore smooth, controlled door movement and help the door close and seal properly.

• Limits door swing to prevent overextension and impact with walls or cabinets
• Reduces hinge stress and helps maintain proper door alignment
• Common signs of failure: door opens too far, binds at the hinge, or the original stop is cracked/missing
• Restores smooth, controlled door motion and closure

• Disconnect power and remove items from the door to reduce weight
• Support the door before loosening any hinge fasteners
• Install the new stop in the correct orientation for your model
• Adjust hinges if needed

This door stop limits the opening angle of the refrigerator/freezer door to prevent overextension that can stress hinges or strike nearby cabinets. Replacing a worn or missing stop restores controlled door travel and helps prevent impact damage.

• Controls and limits the door's opening range
• Helps protect hinges, gaskets, and adjacent cabinets from overextension
• Restores smooth, consistent door operation
• Common signs: door swings past normal position, door hits wall/cabinet, visible broken or missing stop

• Unplug the appliance and lighten the door if needed for easier handling
• Support the door; remove hinge fasteners or pin as needed to access the stop
• Match the orientation of the original stop; retain any shims/spacers in the same order
• Reassemble and verify door alignment and gasket seal

The Door Stop is an OEM part for Frigidaire refrigerators. This small part helps protect the appliance's door from damage and prevents it from impacting walls or adjacent cabinetry, ensuring the longevity and integrity of your refrigerator's exterior. 

Causes of a bad Door Stop can range from physical damage due to forceful door opening, to normal wear and tear from repeated use. In some cases, the mounting area for the door stop may become worn or damaged, affecting its ability to hold the door stop securely.

Symptoms of a bad Door Stop include:

• The refrigerator door swings open wider than usual
• Noticeable wear, damage, or breakage on the door stop
• Difficulty in opening or closing the door smoothly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

A small black replacement plug button that restores a clean, finished appearance and helps keep controls and openings free from dirt and moisture. Designed as a direct-fit cosmetic and protective cap for compatible appliance openings. What it does

• Covers exposed holes or button openings to prevent debris and spills from entering internal areas
• Restores the original look where a worn or missing plug detracts from the appliance finish
• Holds in place to protect underlying components from accidental contact
• Useful when replacing control bezels or trim that require a matching push-in cap

• Disconnect power to the appliance before performing any service work
• Press the plug button squarely into the opening until it snaps into place; no special tools typically required
• Inspect the mounting hole for damage or debris before installing to ensure a secure fit
• If the part does not seat properly, do not force it; verify correct part and orientation

Note: Quantity is one plug button.

Color: White

This full refrigerator door replaces a damaged or worn outer door to restore the appliance's appearance and proper access to the fresh-food compartment. It provides a solid closure surface and helps maintain normal cooling performance when properly installed. What it does:

• Replaces a dented, cracked, or cosmetically damaged outer refrigerator door
• Restores proper sealing and alignment when used with an intact gasket and hinge hardware
• Provides the mounting surface for handles, trim, and door-mounted storage
• Helps prevent cold air loss from the fresh-food compartment when installed correctly

• Disconnect power and empty the door of food and removable bins before beginning
• Many doors require two people to safely lift and align during installation
• Retain and reuse original hinges, pins, and hardware unless the replacement explicitly includes them

INCLUDES 1 HANDLE AND MOUNTING HARDWARE

The Black Handle Kit is an OEM part for Frigidaire refrigerators. It includes new black handles that replace old or damaged ones. Doors and refrigerator components undergo frequent use which can cause handles to show wear through opening and closing motions over many cycles.

Causes of bad handles can be normal wear and tear like scratches, discoloration, loose or missing screws from repeated use. Excessive force when closing doors poses risk of cracks or breaks too.

Symptoms of bad handles include:

• Scratches, chips or discoloration of handle surfaces
• Loose, wobbly or unstable gripping feel
• Difficulty smoothly opening/closing doors due to poor handles
• Cracks or broken pieces that compromise function

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Door Handle Kit is an OEM part for Frigidaire refrigerators. This kit includes the door handle and the necessary mounting hardware to ensure a secure fit. The kit is comprised of one door handle, along with three screws for attachment. It also comes with a set of instructions to guide users through the installation process. 

Over time, door handles can become loose, cracked, or break entirely due to frequent use, mishandling, or impact. Replacing a worn or damaged door handle is essential to maintain the functionality and appearance of the refrigerator.

Symptoms of a bad door handle include:

• Difficulty in opening or closing the refrigerator door
• A loose or wobbly handle
• Visible cracks or breakage in the handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Screw is an OEM part for Frigidaire appliances. This specific screw is designed for Frigidaire models, ensuring a secure fit and proper function in the appliance assembly. Screws like this one are critical for holding components together tightly, contributing to the overall stability and durability of the appliance. Whether used in refrigerators, ovens, washers, or dryers, this screw plays a pivotal role in assembly and maintenance tasks, ensuring parts remain securely fastened during operation.

Over time, screws can become loose, stripped, or lost during repairs or adjustments, potentially compromising the appliance's integrity and performance.  

Symptoms of needing replacement screws include:

• Loose parts or panels on the appliance
• Difficulty in securing components during assembly or maintenance
• The need to replace lost or damaged screws during repair work

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Screw Kit is an OEM part for Frigidaire appliances. It contains various screws specifically designed to fit and secure different components of Frigidaire appliances, ensuring a tight and secure assembly. This kit is essential for both initial installations and for making repairs or replacements to existing appliances, providing the necessary hardware to maintain or restore the structural integrity of your appliance.  These screws are #10-16 x .500 inches long and can be loosened or tightened using either a Phillips-head or square-head screwdriver.

Symptoms of needing a new Screw Kit include:

• Loose components or panels on your appliance due to missing or damaged screws.
• Inability to securely fasten parts during assembly or repairs, which can lead to operational issues or safety hazards.
• Screws stripping or corroding over time, which can compromise the stability and durability of the appliance.

Causes for replacing screws can include mechanical stress that causes screws to loosen or fall out, environmental factors like moisture leading to corrosion, or accidental damage during cleaning or maintenance.

This screw kit is designed to be universally compatible with various Frigidaire models, ensuring that you have the right screws for a range of repair needs.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It is designed to facilitate the smooth opening and closing of the refrigerator door by providing a pivot point for the door hinge. This bearing ensures that the door moves easily and remains properly aligned, helping to maintain a tight seal and optimal refrigerator performance.

Causes of a bad hinge bearing can include regular wear and tear from frequent use, exposure to moisture or temperature changes, and physical damage due to accidental impacts. Over time, these factors can cause the hinge bearing to wear out, become loose, or break, affecting the door's functionality.

Symptoms of a bad hinge bearing include:

• Difficulty opening or closing the refrigerator door
• The door not staying in place or sagging
• Unusual noises, such as squeaking or grinding, when the door is moved
• The door not sealing properly, leading to temperature fluctuations inside the refrigerator

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It plays a critical role in the smooth operation of the refrigerator door by providing a pivot point for the hinge. This small component helps to ensure that the door opens and closes smoothly and seals properly, which is essential for maintaining the refrigerator's internal temperature and energy efficiency.

Symptoms of a bad Hinge Bearing include:

• Difficulty in opening or closing the refrigerator door.
• Squeaking or grinding noises when the door moves.
• The door hanging unevenly or not sealing correctly, potentially leading to temperature fluctuations inside the fridge.

Causes of a bad hinge bearing can include wear and tear from the frequent use of the refrigerator door, accumulation of dirt or grime that impedes smooth movement, or degradation of the material over time due to environmental factors such as moisture.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.