Parts for Frigidaire FGTR1842TP1: Door Parts

Freezer door gasket keeps an airtight seal around the door to lock in cold air and keep moisture out. Replacing a worn, gray magnetic gasket helps maintain temperature, reduce frost and condensation, and support consistent cooling performance.

• Seals the freezer door perimeter to prevent warm-air leaks
• Helps hold set temperature and reduce frost/condensation
• Replaces torn, warped, or permanently compressed gaskets
• Common symptoms: frost along door edges, door not closing flush, warm spots, or longer run times

• Disconnect power to the refrigerator before servicing
• Warm the gasket in hot water or with a low-heat hair dryer to relax shipping creases; do not overheat
• Seat the gasket bead into the door channel; start at corners and work evenly around
• After installation, check the seal with a paper test and allow up to 24 hours for the gasket to conform; adjust door alignment if needed

The Freezer Door Gasket is an OEM part for Frigidaire refrigerators, specifically designed to create an airtight seal around the freezer door. This gasket prevents warm air from entering and cold air from escaping the freezer compartment, ensuring efficient cooling and energy efficiency. Made from durable rubber, this gasket is flexible yet strong, designed to withstand the constant opening and closing of the freezer door.  

Causes of a bad Freezer Door Gasket can include wear and tear over time, exposure to excessive moisture leading to mold or mildew buildup, or damage from cleaning products or sharp objects. 

Symptoms of a bad Freezer Door Gasket include:

• Visible cracks, tears, or warping in the gasket.
• Condensation or ice buildup around the door edges.
• The freezer struggles to maintain the set temperature.
• Increased energy consumption as the freezer works harder to keep cold.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This freezer door gasket is an OEM replacement part for Frigidaire refrigerators. The gasket measures approximately 28" wide x 18" long. This gasket is a perfect fit for your refrigerator's inner door panel.

Symptoms of a bad freezer door gasket include:

• Difficulty keeping interior cold temperatures below 0°F  
• Frost buildup around top and sides of door seals
• Defrosts required increasing in frequency
• Visible air gaps noticeable along gasket perimeter

Causes of a bad freezer door gasket can include material breakdown due to hundreds of door opening and closing compression cycles over time developing small cracks in the rubber. Spills along bottom edges may promote seal deterioration if not cleaned promptly.

This genuine Frigidaire replacement gasket is compatible with other brands such as Electrolux and Kenmore as well 

NOTE: To achieve a smooth installation, simply soak the gasket in warm water or use a hair dryer on low heat to eliminate any folds or creases.

The Refrigerator Door Gasket is an OEM replacement part for Frigidaire refrigerators. As a crucial sealing component, it works to prevent air and temperature leakage around the refrigerator door. The gasket creates an air-tight seal when the door is closed, maintaining proper cooling and preserving freshness inside.

The causes of a bad gasket can include cracks, dried-out or degraded rubber, or damage from repeated door openings and closings.

Symptoms of a bad gasket include:

• Increased humidity or moisture inside the refrigerator
• Difficulty keeping temperatures low enough
• Frost or ice build-up around the door perimeter

This OEM part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Replaces a worn refrigerator door seal on the fresh-food compartment to restore a tight, even seal. Helps maintain cold temperatures, reduce condensation around the door, and cut energy loss when the old gasket is torn, warped, or gapped.

What it does

• Creates a continuous seal around the fresh-food door to keep cold air in.
• Helps prevent warm-air leaks that cause temperature swings.
• Reduces moisture/sweating along the door edge.
• Addresses gaps, tears, cracks, or a gasket that won’t lie flat.

What’s included
One refrigerator door gasket for the fresh-food door (black).

Install notes

• Unplug the refrigerator before starting.
• Warm the new gasket (soak in warm water or use low-heat hair dryer) to relax folds.
• Seat the gasket lip fully into the door channel—start at the corners and work around.
• Close the door and check for uniform contact (paper-pull test); level/adjust hinges as needed and allow 24 hours for the gasket to conform.

The Refrigerator Door Gasket is an OEM replacement part for Frigidaire refrigerators. This crucial component is responsible for creating an airtight seal around the refrigerator door, ensuring efficient temperature control and energy conservation. This gasket is "approximately" 28” by 41”, and may require a screwdriver to remove the old gasket.

Symptoms of needing to replace the refrigerator door gasket include:

• Difficulty in closing the refrigerator door properly
• Visible gaps or gaps around the door gasket area
• Condensation buildup or frost formation around the door gasket
• Increased energy consumption due to inefficient sealing

Causes of a faulty door gasket can include normal wear and tear over time, exposure to extreme temperatures or UV light, or physical damage due to impact or mishandling.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

This clear refrigerator bin stores and organizes food items on a shelf or in a door, keeping groceries contained and easy to access. It replaces cracked, broken, or missing bins so items stop shifting or falling. What it does:

• Holds and organizes produce, deli items, or packaged foods to maximize usable shelf space
• Prevents items from sliding and reduces spills inside the refrigerator
• Restores proper fit where a damaged or missing bin causes gaps or instability
• Compatible with models that use a straight-fit clear storage bin design

• One clear refrigerator bin

• Remove all contents and open the shelf or door fully before installing
• Align bin with shelf rails or mounting slots and slide until it seats securely
• Do not force; if it does not seat easily, inspect for obstructions or misaligned rails
• Clean with mild soap and water; avoid abrasive pads or strong solvents that can damage the plastic

This refrigerator door bin provides a sturdy shelf inside the door to hold bottles, condiments, and small containers for organized storage and easy access. Durable, easy-to-clean plastic replaces a cracked or missing shelf. What it does:

• Holds bottles, jars, and small food containers securely on the refrigerator door
• Restores lost storage space after a cracked or broken door shelf
• Keeps items accessible and helps prevent spills inside the fridge
• Fits into existing door tracks and supports everyday use

• One refrigerator door bin

• Remove contents from the door before replacing the bin
• Slide the old bin out of the door track and align the new bin into the same track until it snaps into place
• No tools typically required; for model-specific instructions
• Disconnect power only if instructed by your model's service manual for interior work

This replacement door bin mounts on the appliance door to hold items securely. Restore organized, usable storage when the original bin is cracked, loose, or missing, and help prevent items from tipping or falling as the door moves.

• Attaches to door liner rails to provide convenient, accessible storage and maximize space
• Replaces a bin that is cracked, warped, broken, or missing
• Common symptoms include broken end tabs, bin won't stay seated, wobbling/sagging, or items falling during door operation
• Matches the original fit for the designated door position on compatible models

• Remove contents; lift the old bin straight up and out of the door slots
• Align the new bin with the tabs/rails and press down until fully seated
• Verify the door closes freely; distribute weight evenly and avoid overloading
• If the bin is very cold, allow it to warm to room temperature before installation to reduce stress on the plastic

This small black plug/button covers a hinge or bearing access hole to restore a finished appearance and help keep out dirt and debris. It's a simple, inexpensive trim piece that maintains the appliance's look and helps protect internal components. What it does:

• Covers exposed hinge or bearing access holes for a clean, finished appearance
• Helps keep dust and debris out of hinge or bearing cavities
• Prevents snagging and reduces the chance of small items entering the opening
• Matches factory appearance and fit for a seamless repair

• Push-fit design; press into the hole until fully seated
• Keep away from small children — small part is a choking hazard

This plug button is a small control panel push button used on select Frigidaire appliances to replace a worn or broken button and restore normal user control. It snaps into the panel for a clean, factory-fit appearance. What it does:

• Acts as the tactile push button used to operate a specific control or function on the appliance
• Replaces cracked, loose, or missing buttons that prevent consistent button actuation
• Restores proper contact engagement so the control registers presses reliably
• Helps eliminate cosmetic damage and keeps the control surface sealed against debris

• One plug button

• Snap-in replacement; remove power to the appliance before attempting any service
• If button is attached to an electronics assembly, handle boards and connectors carefully to avoid damage
• Use basic hand tools as needed and avoid forcing parts—verify orientation before snapping into place

Color: White. Used to cover the hinge bearing hole.

Replacement outer freezer door panel that restores the appliance's exterior appearance and provides the correct surface for the door assembly. Use this panel when the original is dented, cracked, or cosmetically damaged. What it does:

• Replaces a damaged or dented outer freezer door surface
• Restores original appearance and finish on the freezer door
• Provides the proper mounting surface for door trim, handles, and hardware
• Helps the door close and align correctly when panels and trim are intact

• Disconnect power and empty the door area before beginning work
• Follow the appliance service manual to remove the door and transfer any trim, handles, or insulation as needed
• Wear gloves to protect against sharp edges and protect painted surfaces during installation

This part is a complete freezer door intended for top freezer refrigerators.Before installing this part, make sure to unplug the refrigerator or turn off the circuit breaker. To replace the door, locate the hinges that attach it. Near the hinges, find the screws that secure the hinge and unthread them. Pull the door out from the hinge and set it to the side. Place the new door on the hinge and secure the screws that hold it in place. This genuine OEM replacement complete freezer door is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore brand refrigerators.

This name plate is the exterior ID label that restores the appliance's factory identification and appearance. It replaces a faded, torn, or missing label so the unit is easier to identify and looks finished. What it does:

• Provides the factory identification label used for appliance identification and service reference
• Restores the appliance's exterior appearance where the original label was damaged or missing
• Helps owners model/serial information displayed on the appliance surface
• Fits the location originally occupied by the manufacturer's label (surface-mount style)

• One replacement name plate

• Install using the original fasteners or adhesive; do not force or bend the plate
• Clean and dry the mounting area before installation for proper adhesion or fit
• Disconnect power to the appliance before working in areas that expose electrical components
• If original mounting hardware is missing or damaged, use like-for-like replacements rated for appliance use

This door stop limits the opening range of your refrigerator door to prevent overextension and hinge strain. Replace a worn or broken stop to restore controlled door movement and protect surrounding cabinetry from accidental impacts. What it does:

• Controls how far the door opens to prevent overextension and damage
• Helps maintain proper door alignment and reduces stress on the hinges
• Replaces cracked, deformed, or missing stops that no longer hold the door at its stop point
• Common symptoms include the door swinging too far, a hard "clunk" at full open, or visible damage to the stop

• 1 door stop

• Disconnect power; turn off water supply if your unit has a dispenser/ice maker
• Support the door before loosening any hinge fasteners to access the stop
• Note the stop's orientation and position; transfer any spacers and reinstall the same way
• Open and close the door to verify proper range and clearance before fully tightening fasteners

This door stop limits the refrigerator door's opening range to protect hinges and nearby cabinets. Replace a cracked or missing stop to restore smooth, controlled door movement and help the door close and seal properly.

• Limits door swing to prevent overextension and impact with walls or cabinets
• Reduces hinge stress and helps maintain proper door alignment
• Common signs of failure: door opens too far, binds at the hinge, or the original stop is cracked/missing
• Restores smooth, controlled door motion and closure

• Disconnect power and remove items from the door to reduce weight
• Support the door before loosening any hinge fasteners
• Install the new stop in the correct orientation for your model
• Adjust hinges if needed

This door stop limits the opening angle of the refrigerator/freezer door to prevent overextension that can stress hinges or strike nearby cabinets. Replacing a worn or missing stop restores controlled door travel and helps prevent impact damage.

• Controls and limits the door's opening range
• Helps protect hinges, gaskets, and adjacent cabinets from overextension
• Restores smooth, consistent door operation
• Common signs: door swings past normal position, door hits wall/cabinet, visible broken or missing stop

• Unplug the appliance and lighten the door if needed for easier handling
• Support the door; remove hinge fasteners or pin as needed to access the stop
• Match the orientation of the original stop; retain any shims/spacers in the same order
• Reassemble and verify door alignment and gasket seal

The Door Stop is an OEM part for Frigidaire refrigerators. This small part helps protect the appliance's door from damage and prevents it from impacting walls or adjacent cabinetry, ensuring the longevity and integrity of your refrigerator's exterior. 

Causes of a bad Door Stop can range from physical damage due to forceful door opening, to normal wear and tear from repeated use. In some cases, the mounting area for the door stop may become worn or damaged, affecting its ability to hold the door stop securely.

Symptoms of a bad Door Stop include:

• The refrigerator door swings open wider than usual
• Noticeable wear, damage, or breakage on the door stop
• Difficulty in opening or closing the door smoothly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

A small black replacement plug button that restores a clean, finished appearance and helps keep controls and openings free from dirt and moisture. Designed as a direct-fit cosmetic and protective cap for compatible appliance openings. What it does

• Covers exposed holes or button openings to prevent debris and spills from entering internal areas
• Restores the original look where a worn or missing plug detracts from the appliance finish
• Holds in place to protect underlying components from accidental contact
• Useful when replacing control bezels or trim that require a matching push-in cap

• Disconnect power to the appliance before performing any service work
• Press the plug button squarely into the opening until it snaps into place; no special tools typically required
• Inspect the mounting hole for damage or debris before installing to ensure a secure fit
• If the part does not seat properly, do not force it; verify correct part and orientation

Note: Quantity is one plug button.

Color: White

INCLUDES 1 HANDLE AND MOUNTING HARDWARE

The Black Handle Kit is an OEM part for Frigidaire refrigerators. It includes new black handles that replace old or damaged ones. Doors and refrigerator components undergo frequent use which can cause handles to show wear through opening and closing motions over many cycles.

Causes of bad handles can be normal wear and tear like scratches, discoloration, loose or missing screws from repeated use. Excessive force when closing doors poses risk of cracks or breaks too.

Symptoms of bad handles include:

• Scratches, chips or discoloration of handle surfaces
• Loose, wobbly or unstable gripping feel
• Difficulty smoothly opening/closing doors due to poor handles
• Cracks or broken pieces that compromise function

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

INCLUDES 1 HANDLE AND MOUNTING HARDWARE

The Black Handle Kit is an OEM part for Frigidaire refrigerators. It includes new black handles that replace old or damaged ones. Doors and refrigerator components undergo frequent use which can cause handles to show wear through opening and closing motions over many cycles.

Causes of bad handles can be normal wear and tear like scratches, discoloration, loose or missing screws from repeated use. Excessive force when closing doors poses risk of cracks or breaks too.

Symptoms of bad handles include:

• Scratches, chips or discoloration of handle surfaces
• Loose, wobbly or unstable gripping feel
• Difficulty smoothly opening/closing doors due to poor handles
• Cracks or broken pieces that compromise function

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Door Handle Kit is an OEM part for Frigidaire refrigerators. This kit includes the door handle and the necessary mounting hardware to ensure a secure fit. The kit is comprised of one door handle, along with three screws for attachment. It also comes with a set of instructions to guide users through the installation process. 

Over time, door handles can become loose, cracked, or break entirely due to frequent use, mishandling, or impact. Replacing a worn or damaged door handle is essential to maintain the functionality and appearance of the refrigerator.

Symptoms of a bad door handle include:

• Difficulty in opening or closing the refrigerator door
• A loose or wobbly handle
• Visible cracks or breakage in the handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Handle Kit is an OEM part for Frigidaire refrigerators. This kit includes the door handle and the necessary mounting hardware to ensure a secure fit. The kit is comprised of one door handle, along with three screws for attachment. It also comes with a set of instructions to guide users through the installation process. 

Over time, door handles can become loose, cracked, or break entirely due to frequent use, mishandling, or impact. Replacing a worn or damaged door handle is essential to maintain the functionality and appearance of the refrigerator.

Symptoms of a bad door handle include:

• Difficulty in opening or closing the refrigerator door
• A loose or wobbly handle
• Visible cracks or breakage in the handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement mounting screw secures components and panels in refrigerators and freezers, restoring proper fit and stopping loose or rattling parts. Use when original screws are missing, stripped, or damaged. What it does:

• Fastens trim, panels, brackets or small components to the appliance frame
• Restores secure attachment to stop rattling or intermittent contact
• Replaces stripped, corroded, or missing screws to prevent parts from shifting
• Simple, direct replacement that matches the original mounting point

• Use the matching driver bit to avoid stripping the screw head
• Tighten until snug; do not overtighten to prevent thread damage
• Disconnect power to affected appliance areas before servicing if panels expose wiring
• If threads are damaged, replace the mating nut or tapped insert as needed

This replacement screw secures select refrigerator door handles to the door. A worn or missing screw can leave the handle loose or detached, making the door difficult to open and potentially stressing other components.

• Holds the door handle firmly to the door
• Helps restore proper door operation and safe grip
• Designed to fit designated mounting points for compatible models

• Unplug the refrigerator before beginning work
• Open the door to access the handle mounting points
• Use the correct screwdriver/Allen tool to avoid stripping the head
• Start threads by hand and tighten snugly—do not overtighten

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Screw Kit is an OEM part for Frigidaire appliances. It contains various screws specifically designed to fit and secure different components of Frigidaire appliances, ensuring a tight and secure assembly. This kit is essential for both initial installations and for making repairs or replacements to existing appliances, providing the necessary hardware to maintain or restore the structural integrity of your appliance.  These screws are #10-16 x .500 inches long and can be loosened or tightened using either a Phillips-head or square-head screwdriver.

Symptoms of needing a new Screw Kit include:

• Loose components or panels on your appliance due to missing or damaged screws.
• Inability to securely fasten parts during assembly or repairs, which can lead to operational issues or safety hazards.
• Screws stripping or corroding over time, which can compromise the stability and durability of the appliance.

Causes for replacing screws can include mechanical stress that causes screws to loosen or fall out, environmental factors like moisture leading to corrosion, or accidental damage during cleaning or maintenance.

This screw kit is designed to be universally compatible with various Frigidaire models, ensuring that you have the right screws for a range of repair needs.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It is designed to facilitate the smooth opening and closing of the refrigerator door by providing a pivot point for the door hinge. This bearing ensures that the door moves easily and remains properly aligned, helping to maintain a tight seal and optimal refrigerator performance.

Causes of a bad hinge bearing can include regular wear and tear from frequent use, exposure to moisture or temperature changes, and physical damage due to accidental impacts. Over time, these factors can cause the hinge bearing to wear out, become loose, or break, affecting the door's functionality.

Symptoms of a bad hinge bearing include:

• Difficulty opening or closing the refrigerator door
• The door not staying in place or sagging
• Unusual noises, such as squeaking or grinding, when the door is moved
• The door not sealing properly, leading to temperature fluctuations inside the refrigerator

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It plays a critical role in the smooth operation of the refrigerator door by providing a pivot point for the hinge. This small component helps to ensure that the door opens and closes smoothly and seals properly, which is essential for maintaining the refrigerator's internal temperature and energy efficiency.

Symptoms of a bad Hinge Bearing include:

• Difficulty in opening or closing the refrigerator door.
• Squeaking or grinding noises when the door moves.
• The door hanging unevenly or not sealing correctly, potentially leading to temperature fluctuations inside the fridge.

Causes of a bad hinge bearing can include wear and tear from the frequent use of the refrigerator door, accumulation of dirt or grime that impedes smooth movement, or degradation of the material over time due to environmental factors such as moisture.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This genuine replacement screw restores a secure hold for panels, trim, or internal components. It replaces worn or missing fasteners so parts stay aligned and appliances operate safely. What it does:

• Fastens panels, brackets, or trim into place
• Replaces stripped, missing, or damaged screws
• Helps stop rattling, loose panels, or misaligned trim
• Fits OEM mounting locations that require the specified machine screw

• Use the correct driver to avoid stripping the head
• Hand-start the screw, then tighten to firm snug; do not over-torque
• Disconnect power to the appliance before accessing internal components
• If other fasteners are damaged, inspect and replace as needed

This part number contains one (1) screw.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a service wrench used to loosen and tighten appliance fasteners for maintenance and repairs, making access and part replacement easier for technicians and DIYers. Durable tool designed for specific appliance fastener sizes. What it does:

• Provides the correct fit and leverage for removing or installing designated appliance nuts, bolts, and fittings
• Helps safely access internal components during service and part replacement
• Reduces risk of rounding fasteners compared with improvised tools
• Useful for routine maintenance tasks and repair procedures that require a dedicated wrench

• One wrench

• Use the wrench only for its intended appliance fasteners; avoid excessive force
• Disconnect power and water to the appliance before beginning service
• Wear safety gloves and eye protection when working on appliances