Parts for Frigidaire GLHT218WHW2: 03 - Door Parts

The Frigidaire PureSource Plus WFCB Refrigerator Water Filter is an OEM part for Frigidaire refrigerators. This water filter is specifically engineered to reduce impurities and contaminants in your drinking water and ice, including chlorine taste and odor, lead, cysts, and particulates. 

Regular replacement of the water filter is recommended to maintain the best water quality and flow rate. Over time, the filter can become clogged with particles and contaminants, which can reduce its effectiveness and potentially affect the taste and odor of your water.

Symptoms of a filter that needs replacement include:

• Reduced water flow from the dispenser
• Unpleasant taste or odor in the water and ice
• The refrigerator's water filter indicator light turns on

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This freezer door gasket creates a tight seal around the door to keep cold air in and humid air out—helping maintain set temperatures, reduce frost buildup, and support efficient, reliable freezer performance. What it does:

• Seals the freezer door perimeter to prevent air leaks and warm air infiltration
• Helps maintain consistent freezer temperature and energy efficiency
• Helps reduce frost/ice buildup and condensation around the door
• A worn, torn, or warped gasket can lead to poor sealing, frost, moisture, or longer run times

• 1 freezer door gasket

• Disconnect power before servicing
• Allow the new gasket to warm and relax (room temperature or warm water) for easier installation; do not overheat
• Remove the old gasket; clean and dry the door channel, then press the new gasket fully into place, starting at the corners
• After installation, check for uniform contact all around; adjust the door/hinges if needed and verify with a paper-slip test

The Refrigerator Door Gasket is an OEM part for Frigidaire refrigerators, designed to seal the door of the refrigerator compartment, ensuring an airtight closure. This door gasket plays a crucial role in maintaining the efficiency of the refrigerator by preventing cold air from escaping and warm air from entering.

Common causes for a Refrigerator Door Gasket to fail include normal wear and tear from opening and closing the door, damage from cleaning or misuse, and aging of the material, which can lead to hardening and loss of elasticity.

Symptoms of a bad Refrigerator Door Gasket include:

• Noticeable gaps or tears in the gasket
• The refrigerator door does not close as tightly as it should, or it requires more force to close.
• Condensation or frost buildup around the door edges
• An increase in energy consumption

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Dairy Door is an OEM replacement part for Frigidaire side-by-side refrigerators. As the access point to the dedicated dairy compartment, the door is designed with precision seals to maintain optimal humidity levels inside. This helps keep dairy and other perishable items fresh longer.

Causes of a bad dairy door can include worn or damaged seals, dents or impacts warping the door frame, or issues with the electronic components that control humidity levels.

Symptoms of a bad dairy door include: 

• Excessive frost or ice buildup inside the dairy compartment   
• Difficulty opening and closing the door smoothly  
• Warm or dried-out dairy products despite a cold refrigerator interior
• Moisture leaks around the door seals  

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore side-by-side models.

This freezer door assembly replaces a damaged or dented outer door to restore sealing, insulation and appearance for upright freezer compartments. It provides the structural panel and mounting area needed for normal door operation. What it does:

• Replaces the freezer compartment outer door panel and restores a proper seal against the cabinet
• Supports door hardware and hinge attachment so the door opens and closes smoothly
• Helps maintain cold temperatures by preserving the insulated barrier
• Addresses symptoms such as visible dents, cracks, failed seal contact, or a door that won't close flush

• High-level swap; door may require two people to handle safely due to size and weight
• Keep power to the appliance off and remove food from the freezer before servicing
• Verify hinge locations and fasteners on your model—use existing hardware unless new fasteners are specified
• If gasket or inner liner is damaged, inspect and replace those parts separately

This door stop limits the refrigerator door's opening range to protect hinges and nearby cabinets. Replace a cracked or missing stop to restore smooth, controlled door movement and help the door close and seal properly.

• Limits door swing to prevent overextension and impact with walls or cabinets
• Reduces hinge stress and helps maintain proper door alignment
• Common signs of failure: door opens too far, binds at the hinge, or the original stop is cracked/missing
• Restores smooth, controlled door motion and closure

• Disconnect power and remove items from the door to reduce weight
• Support the door before loosening any hinge fasteners
• Install the new stop in the correct orientation for your model
• Adjust hinges if needed

This door stop limits the opening angle of the refrigerator/freezer door to prevent overextension that can stress hinges or strike nearby cabinets. Replacing a worn or missing stop restores controlled door travel and helps prevent impact damage.

• Controls and limits the door's opening range
• Helps protect hinges, gaskets, and adjacent cabinets from overextension
• Restores smooth, consistent door operation
• Common signs: door swings past normal position, door hits wall/cabinet, visible broken or missing stop

• Unplug the appliance and lighten the door if needed for easier handling
• Support the door; remove hinge fasteners or pin as needed to access the stop
• Match the orientation of the original stop; retain any shims/spacers in the same order
• Reassemble and verify door alignment and gasket seal

Color- White; Use this handle if mounted on the left side. If mounted on the right use part number 5304492832.

The Door Handle Set is an OEM part for Frigidaire refrigerators, ensuring a perfect fit and finish for your appliance. This set includes handles for both the refrigerator and freezer doors, designed to replace broken or worn-out handles, providing a secure and comfortable grip for opening and closing the doors.

Causes of damage to the door handle set typically involve physical stress, such as excessive force when opening or closing the door, accidental impacts, and general wear and tear over time. 

Symptoms of a bad Door Handle Set include:

• Handles that are loose or detached, making it difficult to open the door
• Cracked, broken, or worn handles that can lead to injury or further damage to the door
• Difficulty in aligning the handles during installation, indicating potential warping or damage

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Screw Kit is an OEM part for Frigidaire appliances. It contains various screws specifically designed to fit and secure different components of Frigidaire appliances, ensuring a tight and secure assembly. This kit is essential for both initial installations and for making repairs or replacements to existing appliances, providing the necessary hardware to maintain or restore the structural integrity of your appliance.  These screws are #10-16 x .500 inches long and can be loosened or tightened using either a Phillips-head or square-head screwdriver.

Symptoms of needing a new Screw Kit include:

• Loose components or panels on your appliance due to missing or damaged screws.
• Inability to securely fasten parts during assembly or repairs, which can lead to operational issues or safety hazards.
• Screws stripping or corroding over time, which can compromise the stability and durability of the appliance.

Causes for replacing screws can include mechanical stress that causes screws to loosen or fall out, environmental factors like moisture leading to corrosion, or accidental damage during cleaning or maintenance.

This screw kit is designed to be universally compatible with various Frigidaire models, ensuring that you have the right screws for a range of repair needs.

This upper door hinge bearing serves as the low-friction bushing on the top hinge pin so the refrigerator door pivots smoothly. Replacing a worn bearing can stop squeaks and help restore level, easy-opening door operation.

• Provides a low-friction sleeve for the upper hinge pin to reduce wear
• Helps maintain door alignment with the cabinet for a consistent seal
• Common symptoms include squeaking or grinding, door rubbing or sagging, or the door not closing smoothly
• Physical signs include cracks, flattening, or oval-shaped wear in the bushing

• Unplug the refrigerator and remove items from the door
• Support the door; remove the top hinge cover and screws, then lift the door slightly
• Replace the worn upper hinge bearing on the hinge pin or bracket (design varies)
• Reinstall the hinge, align the door, and ensure proper gasket contact

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It plays a critical role in the smooth operation of the refrigerator door by providing a pivot point for the hinge. This small component helps to ensure that the door opens and closes smoothly and seals properly, which is essential for maintaining the refrigerator's internal temperature and energy efficiency.

Symptoms of a bad Hinge Bearing include:

• Difficulty in opening or closing the refrigerator door.
• Squeaking or grinding noises when the door moves.
• The door hanging unevenly or not sealing correctly, potentially leading to temperature fluctuations inside the fridge.

Causes of a bad hinge bearing can include wear and tear from the frequent use of the refrigerator door, accumulation of dirt or grime that impedes smooth movement, or degradation of the material over time due to environmental factors such as moisture.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This actuator controls the refrigerator's internal airflow direction, helping the unit route cold air between compartments for consistent temperatures. Replaces a worn or failed mode/air damper actuator to restore normal airflow control. What it does:

• Moves the mode/air damper or control arm to open and close airflow pathways
• Restores proper compartment temperature balance when the damper is stuck or unresponsive
• Helps stop irregular cooling, warm spots, or fluctuating temperatures tied to damper failure
• Engages with the control board to shift airflow according to selected settings

• One actuator assembly

• Disconnect power before servicing to avoid shock or damage
• Access typically requires removing interior panels or the control housing
• Check connector fit and mounting points; secure actuator before testing

The Door Bin is an OEM part for Frigidaire refrigerators. It provides additional storage space on the refrigerator door, allowing for the convenient organization of smaller items such as condiments, beverages, and jars. This bin is designed to fit securely into the slots on the refrigerator door, making it easy to remove and clean when necessary.

Replace this door bin if it becomes cracked, warped, or no longer fits securely in the door slots. Over time, exposure to varying temperatures and frequent use can cause the plastic to weaken and break.

Symptoms of a bad door bin include:

• Cracks or breakage in the plastic
• Difficulty in securing the bin to the door
• Items falling out or not staying in place

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Shelf Bin is an OEM replacement part for Frigidaire refrigerators. It is designed to fit on the refrigerator door, providing convenient storage space for condiments, bottles, and other small items. This shelf bin helps to keep the refrigerator organized, making it easier to find and reach items stored in the door. 

Causes of a bad door shelf bin can include cracking, breaking, or warping due to overloading, impact from items being moved in and out, or deterioration over time.

Symptoms of a bad door shelf bin include:

• Cracks or breakage in the bin.
• The bin not securely attaching to the door.
• Items falling out or not fitting properly in the bin.
• Difficulty in accessing or retrieving items from the bin.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Freezer Door Shelf Bin is an OEM replacement part for Frigidaire refrigerators. It provides adjustable storage on the inside of the freezer door with removable bin shelves. These bins maximize storage potential in the limited door space through customizable shelving.

Causes of a bad Door Shelf Bin can include shelf breakage from heavy loads, damage to supporting rails or walls of the bin inhibiting proper shelf attachment and use, or broken/missing bin walls reducing structural integrity.

Symptoms of a bad Door Shelf Bin include:

• Detached or missing shelves
• Shelves that do not stay firmly in place when loaded
• Damage or deterioration of bin walls
• Insufficient or compromised storage space

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This water connector links sections of the refrigerator's water supply tubing, maintaining a sealed path to the dispenser and ice maker. Replace a cracked or leaking connector to stop drips and restore reliable water flow and ice production.

• Connects sections of internal water tubing between components (inlet valve, filter, door, ice maker)
• Helps maintain a sealed route for proper dispenser and ice maker operation
• Common symptoms: water leaking behind/under the refrigerator, weak/no dispenser flow, ice maker not filling, visible damage at the fitting
• Direct-fit component built to OEM specifications for the intended application

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Cut tubing ends square and fully insert into the connector until seated; tug gently to confirm engagement
• Restore water, check carefully for leaks, and recheck after the first dispense cycle