Parts for Kenmore 106.7699240 (1067699240, 106 7699240): Door Parts

This freezer door gasket seals the door to the cabinet to keep cold air in and humid air out. Replacing a worn gasket restores a proper seal, helping maintain temperature and reducing frost and condensation around the door.

• Creates a continuous perimeter seal between the freezer door and cabinet
• Helps stabilize freezer temperatures and limits warm-air leaks that can lead to frost/ice buildup
• Common failure signs: torn or hardened gasket, visible gaps, moisture or ice near the door
• Almond color to match compatible units

• Disconnect power to the refrigerator before servicing
• Warm the new gasket in hot water or with low heat to relax folds, then start at the corners and work evenly around the door
• On screw-retained styles, loosen perimeter screws and tuck the gasket lip under the retainer; tighten evenly
• After installation, check seal with a dollar-bill test and allow up to 24 hours for the gasket to fully conform

This is the perimeter seal for the refrigerator's fresh food compartment door. It restores an airtight seal to keep cold air in and humid room air out, helping maintain temperature, reduce condensation, and improve overall efficiency.

• Seals the fresh food door opening to prevent air leaks
• Helps stabilize internal temperature and reduce run time
• Replace if torn, cracked, deformed, or not sealing evenly
• Symptoms can include condensation or moisture around the door, warm spots, frost near the door edge, or the door not closing fully

• Disconnect power; allow the door area and new gasket to warm to room temperature
• Soften the new gasket in warm water to relax bends before installation
• Remove the old gasket; seat the new one fully into the channel, starting at the corners—do not stretch
• Use gentle, low heat (hair dryer) to smooth waves; perform a "paper test" around the perimeter and adjust hinges if needed

This door trim retainer end cap secures the decorative trim on a refrigerator or freezer door, restoring a finished look and keeping the trim aligned. It helps prevent gaps, rattling trim, and moisture intrusion around the door edge. What it does

• Clips into the door trim to hold the trim firmly in place.
• Keeps door trim aligned to reduce cosmetic gaps and noise.
• Helps maintain a proper seal by preventing trim from pulling away.
• Common symptom: visible gap or loose/rattling trim pieces.

• One door trim retainer end cap.

• Designed for a snap-in replacement; may require a flat tool to pry off the old retainer gently.
• Inspect trim and surrounding clips for damage; replace any broken clips before installing.
• Disconnect power only if working near electrical components; this trim replacement is cosmetic/mechanical.

This door trim retainer replaces a broken or missing end cap that holds the door shelf rail/retainer bar in place on the refrigerator or freezer door. It keeps the rail secured so door-shelf contents are properly contained.

• Secures the door shelf trim/retainer bar to the door liner
• Helps keep the rail aligned and prevents it from loosening or falling off
• Replace when the end cap is cracked, missing, or won't hold the rail
• Common symptoms: loose or sagging door rail, bar popping off, gaps at the rail ends

• Disconnect power before servicing
• Support the rail, then release and remove the damaged end cap
• Reuse existing screws/fasteners if your model uses them
• Align and snap/secure the new end cap; ensure the rail is fully seated

This replacement screw secures panels, brackets, and other components in your appliance so they stay tight and properly aligned. Use it to replace missing, stripped, or rusted hardware and eliminate looseness, rattles, or gaps.

• Fastens parts to the cabinet/frame to maintain structural integrity
• Helps keep panels and assemblies aligned to reduce vibration and noise
• Replaces missing, damaged, or corroded screws during service
• Common fix for loose panels or components that no longer hold securely

• Disconnect power and shut off water or gas before servicing
• Match length and thread to the original screw for proper fit
• Hand-start threads to avoid cross-threading; tighten only until snug—do not overtighten
• Tighten them evenly to ensure proper alignment

This sheet-metal screw secures appliance panels, brackets, and components to the cabinet. Replacing a missing or stripped fastener restores a tight, rattle-free fit and helps keep assemblies aligned for reliable operation.

• Fastens sheet-metal parts to the chassis or support brackets
• Replaces stripped, corroded, or lost screws to restore proper hold
• Helps reduce vibration and noise from loose panels
• Maintains alignment of covers, ducts, or trim

• Disconnect power to the appliance; shut off water or gas if applicable.
• Match this screw to the original location and length.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• If the original hole is damaged, repair or replace the mounting point before installing.

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This sheet-metal screw secures appliance panels, brackets, and components to the cabinet. Replacing a missing or stripped fastener restores a tight, rattle-free fit and helps keep assemblies aligned for reliable operation.

• Fastens sheet-metal parts to the chassis or support brackets
• Replaces stripped, corroded, or lost screws to restore proper hold
• Helps reduce vibration and noise from loose panels
• Maintains alignment of covers, ducts, or trim

• Disconnect power to the appliance; shut off water or gas if applicable.
• Match this screw to the original location and length.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• If the original hole is damaged, repair or replace the mounting point before installing.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

Size: 63-1/2 x 35-1/2 x 2-5/8 inch.

This OEM grease is a purpose-made appliance lubricant that reduces friction and protects moving parts for smoother operation and longer component life. Use where specified by the manufacturer for bearings, slides, or motor shafts. What it does:

• Lubricates gears, bearings, rollers and shafts to reduce wear and noise
• Helps prevent binding, seizing, and grinding on moving components
• Protects metal parts from corrosion where grease is specified
• Keeps parts moving smoothly under normal operating temperatures

• Disconnect power before servicing any appliance; follow manufacturer service instructions
• Apply sparingly to clean, dry surfaces; avoid over-greasing which can attract debris
• Wear gloves and wipe excess grease from surrounding areas to prevent staining

The Adhesive is an OEM part for Whirlpool appliances, designed for securing and sealing various components within the appliances. This adhesive is ideal for use in situations where a durable and heat-resistant bond is necessary.Size: 2 oz. tube. This silicone rubber adhesive can be used on door gaskets, felt seals, and much more.

Over time, seals and insulation can become loose or detached due to wear, heat, or mechanical action, potentially compromising the appliance's functionality, efficiency, or safety.

The need for this adhesive may become apparent through symptoms such as:

• Loose seals or gaskets that result in heat loss, inefficiency, or the escape of moisture.
• Detached insulation leading to increased noise, heat transfer, or loss of energy efficiency.
• Components that have become unattached, affecting the appliance's performance or structural integrity.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.