Parts for Frigidaire FFHT1621TS1: Doors Parts

This freezer door gasket forms the airtight seal between the door and cabinet. Replacing a worn or damaged gasket stops air leaks, reduces frost and condensation, and helps the freezer hold the correct temperature and operate efficiently. What it does:

• Seals the freezer door perimeter to keep warm air out and cold air in
• Helps maintain stable internal temperature and energy efficiency
• Reduces frost/ice buildup and moisture around the door opening
• Common symptoms: torn, warped, or brittle gasket; frost along the door edges; door not sealing or popping open

• Includes: 1 freezer door gasket

• Disconnect power and remove items from the freezer door as needed.
• Remove the old gasket and clean the retainer/channel of debris.
• Warm the new gasket with warm water or low heat to relax folds; press it fully into the groove, working evenly around the perimeter.
• Close the door and check for uniform contact all around; use gentle heat to smooth waves and recheck the seal.

The Freezer Door Gasket is an OEM component for Frigidaire refrigerators. It is a rubber-sealing gasket that lines the perimeter of the freezer door. This gasket plays a crucial role in maintaining proper insulation and preventing warm air and moisture from entering the freezer compartment. 

Causes of a bad gasket can include damage from over-tightening of the door, tears or cracks due to age and usage, or warping of the gasket profile from temperature extremes.

Symptoms of a bad freezer door gasket include:

• Frost or moisture buildup inside the freezer  
• Difficulty closing the door fully due to misshapen gasket
• Warm air entering the freezer, causing higher temperatures
• Visible cracks or tears in the rubber seal

This OEM Frigidaire part is compatible with many Electrolux, Gibson, Kelvinator, and Kenmore models. 

This refrigerator door gasket seals the fresh food compartment door to the cabinet, preventing air leaks. Replacing a worn gasket restores a tight seal so the fridge holds temperature better and reduces condensation or frost around the door.

• Forms the air-tight perimeter seal on the fresh food door
• Helps maintain proper temperature and efficiency
• Replaces gaskets that are torn, cracked, shrunken, or won't lay flat
• Common symptoms: door not sealing/closing, warm fridge, moisture or frost at the door, longer run times

• Unplug the refrigerator before servicing
• Let the new gasket relax flat; warm gently (hair dryer or warm water) to remove kinks—do not overheat
• Install starting at the corners and work evenly around the retainer/channel
• Check the seal with a paper-slide test at multiple points; adjust door/hinges if needed

The Refrigerator Door Gasket is an OEM part for Frigidaire refrigerators. This gasket forms an airtight seal around the door, keeping cold air inside and preventing warm air from entering the refrigerator. 

Causes of a bad refrigerator door gasket can include wear and tear over time, exposure to temperature fluctuations, or damage from frequent opening and closing of the door. A faulty gasket can lead to increased energy consumption and reduced cooling efficiency.

Symptoms of a bad refrigerator door gasket include:

• Visible cracks or tears in the gasket
• The door not closing properly or staying closed
• Increased frost buildup inside the refrigerator
• Higher energy bills due to the appliance working harder to maintain temperature

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Rack is an OEM part compatible with Frigidaire refrigerators. It is a convenient storage component designed to fit securely inside the refrigerator door, providing additional space for organizing and storing items.This rack is white in color and measures about 23 inches wide by 3 inches high by 5 inches deep. 

Causes of needing to replace a door rack can include damage from mishandling or impact, wear and tear over time, or the desire to upgrade or customize the interior organization of the refrigerator.

Symptoms indicating it's time for a new door rack include:

• Cracks, breaks, or visible damage to the rack or shelves
• Difficulty in sliding or removing the rack from the door
• Inability to securely hold or support items placed on the rack

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

The Dairy Door is an OEM replacement part for  Frigidaire side-by-side refrigerators. Located inside the fresh food compartment, it provides a dedicated storage area for milk, yogurt, cheese and other dairy products requiring colder temperatures. The door measures approximately 9 inches wide and 5 inches high.

Causes of a bad dairy door include normal wear from repeated opening and closing over time. Exposure to spills inside the refrigerator can also potentially damage door shelf components or seals.

Symptoms of a bad dairy door are: 

• Difficulty opening or closing the door smoothly  
• Door alignment issues where it does not sit flush in the frame
• Leaks or moisture inside the dairy storage area
• Damage or cracks in shelf supports or gasket seals

This OEM part is also compatible with models from brands like Electrolux, Gibson, and Kelvinator brand models.

NOTE: For white use 240337701

The Door Rack is an OEM part for Frigidaire refrigerators. This rack provides additional storage space for bottles, jars, and other condiments. It's an essential component for maximizing the storage capacity and organization of your refrigerator, making the most out of the available space. 

Over time, door racks can experience wear or become damaged due to overloading, accidental impacts, or the natural aging process. This can lead to issues such as the rack becoming loose, cracking, or not being able to securely hold items.

Symptoms of a bad Door Rack include:

• Cracks or breaks in the rack, compromising its structural integrity
• The rack sagging or not attaching securely to the refrigerator door
• Difficulty in sliding the rack in or out, or it not fitting properly
• Reduced effectiveness in holding items securely

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This small black plug/button covers a hinge or bearing access hole to restore a finished appearance and help keep out dirt and debris. It's a simple, inexpensive trim piece that maintains the appliance's look and helps protect internal components. What it does:

• Covers exposed hinge or bearing access holes for a clean, finished appearance
• Helps keep dust and debris out of hinge or bearing cavities
• Prevents snagging and reduces the chance of small items entering the opening
• Matches factory appearance and fit for a seamless repair

• Push-fit design; press into the hole until fully seated
• Keep away from small children — small part is a choking hazard

This plug button is a small control panel push button used on select Frigidaire appliances to replace a worn or broken button and restore normal user control. It snaps into the panel for a clean, factory-fit appearance. What it does:

• Acts as the tactile push button used to operate a specific control or function on the appliance
• Replaces cracked, loose, or missing buttons that prevent consistent button actuation
• Restores proper contact engagement so the control registers presses reliably
• Helps eliminate cosmetic damage and keeps the control surface sealed against debris

• One plug button

• Snap-in replacement; remove power to the appliance before attempting any service
• If button is attached to an electronics assembly, handle boards and connectors carefully to avoid damage
• Use basic hand tools as needed and avoid forcing parts—verify orientation before snapping into place

Color: White. Used to cover the hinge bearing hole.

A replacement freezer door panel that restores the exterior closure for your freezer compartment and helps maintain proper cold seal. Replaces damaged, dented, or discolored door panels to improve appearance and function. What it does

• Replaces the freezer's exterior door panel so the door closes and seals correctly.
• Restores a flat, undamaged surface to prevent cold air loss and reduce frost buildup.
• Helps stop visible damage like dents, cracks, or heavy scratches from affecting use.
• Works with existing hinges, gaskets, and trim when those components are undamaged.

• Inspect hinges, gasket, and mounting hardware before reinstalling; replace if worn.
• Disconnect power to the appliance if removal requires moving electrical components or lights.
• Handle with care to avoid scratching the new panel during installation.

This replacement freezer door restores the enclosure that protects and insulates your freezer compartment, helping maintain cold temperatures and the appliance's appearance. Use it when the original door is dented, bent, or failing to close properly. What it does:

• Replaces a damaged or distorted freezer door to help restore proper closure and insulation
• Helps prevent cold air loss that can lead to frost buildup or food spoilage
• Restores the exterior appearance and provides the mounting surface for handles, gaskets, and interior components
• Addresses symptoms such as visible dents, warping, difficulty closing, or recurring frost/moisture inside the freezer

• Disconnect power before starting and work with a helper—doors can be heavy and awkward
• Remove and transfer existing hinges, handle, gaskets, and any interior trims as required
• Inspect hinge hardware and door gasket for wear; replace damaged hardware or seals to ensure a proper fit
• Follow OEM instructions and torque specifications when tightening hinge fasteners

This replacement name plate is the identification label used on the appliance's exterior to restore a clear, readable ID and finish. It helps keep the appliance looking complete and makes model/serial information visible. What it does:

• Replaces a worn, faded, or missing identification label on the appliance exterior
• Restores the appliance's original appearance and readable markings
• Helps owners locate model/serial details when present on the label
• Prevents confusion caused by missing or damaged name plate graphics

• High-level replacement; clean and dry the mounting surface before installing for best adhesion
• Remove any old adhesive or backing carefully to avoid surface damage
• Align the label precisely, then press firmly to secure
• Disconnect power and follow basic safety precautions when removing exterior panels if required

This door stop limits the opening range of your refrigerator door to prevent overextension and hinge strain. Replace a worn or broken stop to restore controlled door movement and protect surrounding cabinetry from accidental impacts. What it does:

• Controls how far the door opens to prevent overextension and damage
• Helps maintain proper door alignment and reduces stress on the hinges
• Replaces cracked, deformed, or missing stops that no longer hold the door at its stop point
• Common symptoms include the door swinging too far, a hard "clunk" at full open, or visible damage to the stop

• 1 door stop

• Disconnect power; turn off water supply if your unit has a dispenser/ice maker
• Support the door before loosening any hinge fasteners to access the stop
• Note the stop's orientation and position; transfer any spacers and reinstall the same way
• Open and close the door to verify proper range and clearance before fully tightening fasteners

This door stop limits the refrigerator door's opening range to protect hinges and nearby cabinets. Replace a cracked or missing stop to restore smooth, controlled door movement and help the door close and seal properly.

• Limits door swing to prevent overextension and impact with walls or cabinets
• Reduces hinge stress and helps maintain proper door alignment
• Common signs of failure: door opens too far, binds at the hinge, or the original stop is cracked/missing
• Restores smooth, controlled door motion and closure

• Disconnect power and remove items from the door to reduce weight
• Support the door before loosening any hinge fasteners
• Install the new stop in the correct orientation for your model
• Adjust hinges if needed

This door stop limits the opening angle of the refrigerator/freezer door to prevent overextension that can stress hinges or strike nearby cabinets. Replacing a worn or missing stop restores controlled door travel and helps prevent impact damage.

• Controls and limits the door's opening range
• Helps protect hinges, gaskets, and adjacent cabinets from overextension
• Restores smooth, consistent door operation
• Common signs: door swings past normal position, door hits wall/cabinet, visible broken or missing stop

• Unplug the appliance and lighten the door if needed for easier handling
• Support the door; remove hinge fasteners or pin as needed to access the stop
• Match the orientation of the original stop; retain any shims/spacers in the same order
• Reassemble and verify door alignment and gasket seal

The Door Stop is an OEM part for Frigidaire refrigerators. This small part helps protect the appliance's door from damage and prevents it from impacting walls or adjacent cabinetry, ensuring the longevity and integrity of your refrigerator's exterior. 

Causes of a bad Door Stop can range from physical damage due to forceful door opening, to normal wear and tear from repeated use. In some cases, the mounting area for the door stop may become worn or damaged, affecting its ability to hold the door stop securely.

Symptoms of a bad Door Stop include:

• The refrigerator door swings open wider than usual
• Noticeable wear, damage, or breakage on the door stop
• Difficulty in opening or closing the door smoothly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

A small black replacement plug button that restores a clean, finished appearance and helps keep controls and openings free from dirt and moisture. Designed as a direct-fit cosmetic and protective cap for compatible appliance openings. What it does

• Covers exposed holes or button openings to prevent debris and spills from entering internal areas
• Restores the original look where a worn or missing plug detracts from the appliance finish
• Holds in place to protect underlying components from accidental contact
• Useful when replacing control bezels or trim that require a matching push-in cap

• Disconnect power to the appliance before performing any service work
• Press the plug button squarely into the opening until it snaps into place; no special tools typically required
• Inspect the mounting hole for damage or debris before installing to ensure a secure fit
• If the part does not seat properly, do not force it; verify correct part and orientation

Note: Quantity is one plug button.

Color: White

This is a replacement refrigerator outer cabinet door that restores secure closure and the appliance's finished look. It provides a direct-fit exterior door to replace dented, cracked, or otherwise damaged doors. What it does:

• Replaces the damaged outer door panel so the refrigerator seals and looks like new
• Provides mounting locations for hinges, gaskets, and exterior hardware
• Restores proper door alignment and opening/closing function when installed correctly
• Helps prevent drafts and temperature loss caused by bent or warped doors

• 1 refrigerator outer cabinet door

• Disconnect power and empty the door before starting; use two people for safe handling
• Transfer existing hinges, gasket, handles, and trim
• Tighten hinge fasteners and adjust door alignment

This outer refrigerator door replaces a damaged or dented door panel to restore the appliance's seal, appearance, and ease of use. It provides the proper mounting surface for handles, gaskets, and interior shelving. What it does:

• Replaces a cracked, dented, or bent outer door panel that prevents proper closure or looks worn
• Restores door alignment and helps refrigerator maintain an even temperature by supporting the gasket
• Provides the mounting surface for handles, trim, and door accessories
• Helps stop cold-air leaks that can lead to frosting or higher energy use

• Disconnect power and remove food from the door area before starting; doors can be heavy and awkward
• Handle, hinge pins, trim, gaskets, and screws are often reused; verify those parts separately if needed
• Use proper support or a second person when removing and installing the door to avoid damage or injury
• Check door alignment and gasket seating after installation for a proper seal

INCLUDES 1 HANDLE AND MOUNTING HARDWARE

The Black Handle Kit is an OEM part for Frigidaire refrigerators. It includes new black handles that replace old or damaged ones. Doors and refrigerator components undergo frequent use which can cause handles to show wear through opening and closing motions over many cycles.

Causes of bad handles can be normal wear and tear like scratches, discoloration, loose or missing screws from repeated use. Excessive force when closing doors poses risk of cracks or breaks too.

Symptoms of bad handles include:

• Scratches, chips or discoloration of handle surfaces
• Loose, wobbly or unstable gripping feel
• Difficulty smoothly opening/closing doors due to poor handles
• Cracks or broken pieces that compromise function

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Door Handle Kit is an OEM part for Frigidaire refrigerators. This kit includes the door handle and the necessary mounting hardware to ensure a secure fit. The kit is comprised of one door handle, along with three screws for attachment. It also comes with a set of instructions to guide users through the installation process. 

Over time, door handles can become loose, cracked, or break entirely due to frequent use, mishandling, or impact. Replacing a worn or damaged door handle is essential to maintain the functionality and appearance of the refrigerator.

Symptoms of a bad door handle include:

• Difficulty in opening or closing the refrigerator door
• A loose or wobbly handle
• Visible cracks or breakage in the handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Screw is an OEM part for Frigidaire appliances. This specific screw is designed for Frigidaire models, ensuring a secure fit and proper function in the appliance assembly. Screws like this one are critical for holding components together tightly, contributing to the overall stability and durability of the appliance. Whether used in refrigerators, ovens, washers, or dryers, this screw plays a pivotal role in assembly and maintenance tasks, ensuring parts remain securely fastened during operation.

Over time, screws can become loose, stripped, or lost during repairs or adjustments, potentially compromising the appliance's integrity and performance.  

Symptoms of needing replacement screws include:

• Loose parts or panels on the appliance
• Difficulty in securing components during assembly or maintenance
• The need to replace lost or damaged screws during repair work

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Screw Kit is an OEM part for Frigidaire appliances. It contains various screws specifically designed to fit and secure different components of Frigidaire appliances, ensuring a tight and secure assembly. This kit is essential for both initial installations and for making repairs or replacements to existing appliances, providing the necessary hardware to maintain or restore the structural integrity of your appliance.  These screws are #10-16 x .500 inches long and can be loosened or tightened using either a Phillips-head or square-head screwdriver.

Symptoms of needing a new Screw Kit include:

• Loose components or panels on your appliance due to missing or damaged screws.
• Inability to securely fasten parts during assembly or repairs, which can lead to operational issues or safety hazards.
• Screws stripping or corroding over time, which can compromise the stability and durability of the appliance.

Causes for replacing screws can include mechanical stress that causes screws to loosen or fall out, environmental factors like moisture leading to corrosion, or accidental damage during cleaning or maintenance.

This screw kit is designed to be universally compatible with various Frigidaire models, ensuring that you have the right screws for a range of repair needs.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It is designed to facilitate the smooth opening and closing of the refrigerator door by providing a pivot point for the door hinge. This bearing ensures that the door moves easily and remains properly aligned, helping to maintain a tight seal and optimal refrigerator performance.

Causes of a bad hinge bearing can include regular wear and tear from frequent use, exposure to moisture or temperature changes, and physical damage due to accidental impacts. Over time, these factors can cause the hinge bearing to wear out, become loose, or break, affecting the door's functionality.

Symptoms of a bad hinge bearing include:

• Difficulty opening or closing the refrigerator door
• The door not staying in place or sagging
• Unusual noises, such as squeaking or grinding, when the door is moved
• The door not sealing properly, leading to temperature fluctuations inside the refrigerator

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It plays a critical role in the smooth operation of the refrigerator door by providing a pivot point for the hinge. This small component helps to ensure that the door opens and closes smoothly and seals properly, which is essential for maintaining the refrigerator's internal temperature and energy efficiency.

Symptoms of a bad Hinge Bearing include:

• Difficulty in opening or closing the refrigerator door.
• Squeaking or grinding noises when the door moves.
• The door hanging unevenly or not sealing correctly, potentially leading to temperature fluctuations inside the fridge.

Causes of a bad hinge bearing can include wear and tear from the frequent use of the refrigerator door, accumulation of dirt or grime that impedes smooth movement, or degradation of the material over time due to environmental factors such as moisture.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Bin is an OEM part for Frigidaire refrigerators. It is a storage compartment designed to fit securely onto the interior of the refrigerator door, providing convenient and easily accessible storage space for items like beverages, condiments, or other small food items.

Causes of a bad door bin can include cracks or damage due to impact or mishandling, warping or discoloration from exposure to heat or moisture, or wear and tear on the hinges or mounting mechanisms that attach the bin to the door.

Symptoms of a faulty door bin may include:

• Cracks, chips, or other visible damage
• The bin not fitting properly or securely onto the door
• Leaks or spills due to a poorly sealed or damaged bin
• Difficulty opening or closing the bin
• Obstructed access to the bin due to misalignment or warping

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This is the 2 liter bin. For the gallon door bin use part number 240383801.

This Door Shelf Bar is an OEM replacement part for Frigidaire brand refrigerators. This white shelf bar is about 25 inches wide, 4 inches high, and 6 inches deep. It offers plenty of space for your jars and bottles.

Causes of failure relate to stresses from opening and closing the heavy door combined with impacts absorbing gallons placed inside roughing edges. 

Symptoms of a damaged gallon door bin include:

• Cracked or splitting plastic base unable to bear weight  
• Difficulty removing bin from tracks rubbed smooth
• Loose attachment fit from worn mounting supports 
• Contents easily tipping over during door movements

This OEM replacement part is compatible with select Electrolux and Kelvinator models.