Parts for Lg TLD1840CED: Drum And Motor Assembly Parts

This filter guide secures and positions the refrigerator water filter for proper alignment and a reliable seal. It helps keep the filter stable during normal use so water flows correctly and filtration works as intended. What it does:

• Holds the water filter in the correct position inside the filter housing
• Helps maintain a proper seal to reduce the chance of leaks or bypassed water
• Prevents filter movement or rattling when the refrigerator door is opened
• Supports easy removal and replacement of the filter by guiding insertion

• One filter guide

• Designed to install in the refrigerator filter compartment; follow your model's service instructions
• Turn off water supply and relieve system pressure before removing or installing filter components
• Use basic hand tools as required; avoid overtightening which can damage plastic parts
• Inspect surrounding housing and O-rings for wear and replace if needed

Replace your dryer's duct assembly if cracked, broken, or damaged. This component channels air from the drum through the heating system to ensure proper airflow.

Dryer lint filter cover that secures and protects your lint screen. Replace if cracked, broken, or loose to maintain proper airflow and drying efficiency.

If your dryer isn't venting properly or clothes stay damp, a clogged or damaged exhaust duct may be the cause. This assembly restores airflow in 30 minutes.

This Lifter is a replacement shelf support that helps hold and level adjustable refrigerator shelves for smooth raising and lowering. Restores secure shelf positioning so items stay stable and shelves operate correctly. What it does:

• Supports and stabilizes an adjustable refrigerator shelf, preventing sagging.
• Enables smooth lifting and lowering of the shelf when adjusting positions.
• Replaces cracked, broken, or worn plastic support that lets shelves tilt or fall.
• Helps restore proper alignment so refrigerated items sit level.

• One lifter/shelf support.

• Disconnect power to the appliance before starting any repairs.
• Remove the shelf or bin that sits on the lifter to gain access.
• Snap the lifter into the designated mounting slot; some models may require a light push or a screwdriver to assist.

This tub assembly is the main water-containing drum for front-load washers. It replaces a cracked, warped, or damaged tub to stop leaks and restore proper drum rotation and wash performance. What it does:

• Houses the inner drum and contains wash water during cycles
• Supports drum rotation and helps maintain proper agitation/balance
• Stops leaks caused by cracked or warped tubs
• Helps reduce unusual noises or vibration linked to a damaged tub

• Disconnect power and water supply before starting work
• This is a heavy, bulky part — two people are often needed to move and position it safely
• Replace associated seals, gaskets, and fasteners if damaged or worn
• Follow OEM disassembly/reassembly instructions and torque specs; inspect mountings and bearings during install

A manufacturer-configured replacement component designed to restore the appliance's original factory settings and functions. Use this part when a model-specific, pre-configured module is required to return correct operation. What it does:

• Provides the factory-specific configuration and setup programmed by the manufacturer
• Restores functions controlled by the module when configuration or programming is corrupted
• Resolves symptoms such as appliance not starting, control panel unresponsive, or intermittent/erratic operation linked to configuration errors
• Ensures compatibility with model-specific features when the appliance requires a pre-configured assembly

• Disconnect power to the appliance before starting any work
• Handle electronics carefully; observe electrostatic discharge (ESD) precautions for circuit boards or modules
• Match connectors and mounting locations to the original part; do not force connectors

Single wire harness for dryers. Connects electrical components inside the dryer cabinet. Replace if wires are damaged, frayed, or connectors are broken.

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

The Motor Bracket is an OEM part for LG dryers. This bracket securely holds the dryer motor in place. It maintains proper alignment and spacing of the motor to allow for smooth operation of the tumble cycle.

Causes of a bad motor bracket can include cracks or breaks developed over time from repeated use and vibration, or damage due to impact or improper installation.

Symptoms of a bad motor bracket include:

• Excessive noise or grinding sounds emanating from the motor area
• The dryer not rotating or tumbling clothes properly
• Increased movement or shaking of the motor
• Poor airflow and inefficient drying performance

This OEM LG part is also compatible with some Kenmore models.

This is a drum support roller assembly that helps the dryer drum rotate smoothly during operation. The rollers sit along the rear or front of the drum and bear its weight as it spins. Replace this assembly if the dryer makes thumping, squealing, or rumbling noises, or if the drum wobbles or does not turn freely.

Replace your dryer's guide cover trim piece if cracked, broken, or missing. This trim protects the guide area and prevents debris from entering the mechanism.

This clamp secures hoses, tubing or wiring to the appliance frame to help prevent rubbing, vibration and routing issues. It restores a solid attachment point so lines stay in place during normal use. What it does:

• Holds a hose, tubing or wire bundle in place to prevent chafing and abrasion
• Keeps components routed away from moving parts and hot surfaces
• Reduces rattling or vibration caused by loose lines
• Helps maintain safe, reliable connections by preventing strain on fittings

• Disconnect power and shut off water before servicing
• Use basic hand tools; avoid over-tightening which can pinch hoses or wires
• Inspect adjacent hoses/wires for wear and replace if damaged
• Take photos before removal to ensure correct reinstallation

This guide assembly is a replacement slide guide that helps support and align moving components for smooth operation and reliable engagement. It restores proper tracking and reduces wobble or binding in the mechanism. What it does:

• Provides stable support and alignment for a sliding component to prevent mis-tracking and uneven movement
• Reduces noise, sticking, or binding caused by worn or damaged guides
• Helps maintain proper clearance and engagement of the moving part
• Matches OEM fit and mounting points for direct replacement

• Turn off and unplug the appliance before beginning any repair to avoid electrical shock
• Remove any obstructing panels or components to access the guide
• Inspect mating parts (slides, rails, fasteners) and replace any damaged hardware to ensure correct fit

Blower housing assembly for dryer that channels heated air from the drum to the exhaust. Replaces a cracked or damaged housing to restore proper airflow and help the dryer dry more efficiently and quietly. What it does:

• Channels heated air from the drum to the exhaust and supports the blower wheel.
• Restores airflow when a damaged or cracked housing is restricting ventilation.
• Commonly used to address reduced drying performance and longer dry times.
• Can also resolve unusual rattling or grinding noises coming from the lower front of the dryer.

• Disconnect power (and gas, if applicable) before beginning work; wear eye protection and gloves.
• Remove access panels and disconnect vent/ducting per your model's service instructions to reach the blower housing.
• Inspect the blower wheel and surrounding seals/gaskets while the housing is out; replace damaged components as needed.
• Reassemble all panels and venting securely and test the dryer for proper airflow and operation after installation.

Self-tapping screw secures panels, brackets, and components inside your appliance. Replace stripped, corroded, or missing screws to restore secure fit.

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

This replacement screw secures appliance components in their proper position. Use it to restore a tight, rattle-free fit when the original fastener is missing, stripped, or corroded. What it does:

• Fastens brackets, panels, or trim to keep assemblies aligned and secure
• Helps prevent vibration, rattling, and gaps from loose hardware
• Restores proper attachment when a screw is lost, worn, or damaged
• Common symptoms: loose panel/handle, misalignment, rattling, or a missing screw

• Disconnect power; shut off water or gas before service
• Match location to the original; start threads by hand to avoid cross-threading
• Use the correct driver bit; do not overtighten (especially into plastic)
• If the original hole is stripped, repair threads before installing the new screw

This is a fastener and retainer assembly that secures the blower wheel to the motor shaft inside a dryer. It keeps the blower wheel firmly in place so it can properly circulate hot air through the drum and out the exhaust vent. Replace this assembly if the blower wheel wobbles, makes rattling or squealing noises, or if the retainer nut is stripped or broken, causing poor airflow and longer drying times.

Distortion spring that applies tension within the dryer mechanism. Replace if fatigued, broken, or missing to restore proper tension and assembly function.

Dryer drum seal creates an airtight barrier between the rotating drum and housing to maintain drying efficiency. Replace if cracked or hardened. Verify fit with your model number.

The Pressure Sensor is an OEM replacement part for LG dryers. This sensor monitors the airflow or pressure within the dryer, helping to regulate drying cycles and ensure efficient operation. By detecting blockages or changes in airflow, it plays a critical role in maintaining proper performance and preventing overheating.

Over time, the pressure sensor can fail due to wear, electrical issues, or buildup of lint and debris. Damage to the sensor or its connections can cause the dryer to operate inefficiently or stop functioning altogether.

Symptoms of a bad pressure sensor include:

• Dryer not heating properly
• Extended drying times
• Error codes related to airflow or pressure
• Dryer shutting off unexpectedly during cycles

This OEM LG part is also compatible with Sears/Kenmore dryers.

Fix loud banging, grinding noise, or poor drying performance with a new dryer blower wheel. Restores proper airflow through drum and exhaust vent.

This dryer drum belt wraps around the drum and pulleys to spin clothes. Replace if stretched, cracked, or broken to restore tumbling. Confirm fit by model.

Fix a dryer that won't heat or leaves clothes damp with this heating element assembly. Generates heat to dry clothes effectively. DIY repair.

Idler pulley maintains tension on the dryer belt. Replace if worn, cracked, or causing belt slippage. Installs between motor and drum support system.

The Dryer Thermistor is an OEM part for LG dryers, designed to monitor and help regulate the temperature within the dryer by providing feedback to the control board about the temperature inside the drum. This allows the dryer to adjust its heat settings accordingly, preventing overheating and ensuring clothes are dried evenly and safely.

Symptoms of a bad Dryer Thermistor include:

• Clothes not drying properly or taking longer than usual to dry.
• The dryer repeatedly stopping during a cycle.
• Error messages appearing on the dryer's display panel.
• The dryer getting too hot or not heating enough.

Causes of a bad Dryer Thermistor can include a buildup of lint and debris affecting its ability to accurately sense temperature, wear and tear over time, or electrical issues within the dryer's circuitry.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Hi Limit Thermostat Assembly is an OEM part for LG dryers. This thermostat monitors and regulates the temperature within the dryer to prevent overheating, ensuring safe and efficient operation. It acts as a safety device that shuts off the heating element if the dryer exceeds a certain temperature, protecting the appliance and your home from potential fire hazards.

Over time, the hi limit thermostat can fail due to wear and tear, electrical issues, or repeated exposure to high temperatures. If the thermostat becomes faulty, it can lead to improper temperature regulation within the dryer.

Symptoms of a bad hi limit thermostat include:

• The dryer overheating
• The dryer not heating at all
• The dryer shutting off mid-cycle
• Extended drying times due to inconsistent heating

This OEM LG part is also compatible with Sears/Kenmore models.

Captures lint and debris during drying cycles. Replace when torn, cracked, or difficult to remove. Confirm fit using your dryer's model number.

The Dryer Blower Thermostat is an OEM replacement part for LG dryers. It plays a role in regulating the operation of the blower motor, which is responsible for circulating hot air throughout the dryer during the drying cycle.

Causes of a bad dryer blower thermostat can include electrical malfunctions, physical damage, or simply wear and tear over time.

Symptoms of a bad dryer blower thermostat include:  

• The dryer not heating up properly or taking longer to dry clothes
• The blower motor failing to turn on or running continuously
• Inconsistent or inadequate airflow during the drying cycle
• Error codes or fault indicators related to the thermostat or blower motor

This OEM LG part is also compatible with Sears/Kenmore models.

The Hi Limit Thermal Fuse is an OEM part for LG dryers. This fuse is a safety device that protects the dryer from overheating by cutting off power to the heating element if the dryer’s temperature exceeds a safe limit. It ensures that the dryer operates within safe temperature ranges, preventing potential fire hazards.

Replace the hi limit thermal fuse if it becomes faulty due to wear and tear, a buildup of lint, or exposure to high temperatures over time. A malfunctioning fuse can compromise the dryer’s ability to regulate heat properly.

Symptoms of a bad hi limit thermal fuse include:

• The dryer not heating
• The dryer shutting off unexpectedly during a cycle
• No response from the dryer when attempting to start a cycle
• Extended drying times due to lack of heat

This OEM LG part is also compatible with Sears/Kenmore models.