Parts for Kenmore 796.91073310 (79691073310, 796 91073310): Drum And Motor Assembly Parts

This tub assembly is the main water-containing drum for front-load washers. It replaces a cracked, warped, or damaged tub to stop leaks and restore proper drum rotation and wash performance. What it does:

• Houses the inner drum and contains wash water during cycles
• Supports drum rotation and helps maintain proper agitation/balance
• Stops leaks caused by cracked or warped tubs
• Helps reduce unusual noises or vibration linked to a damaged tub

• Disconnect power and water supply before starting work
• This is a heavy, bulky part — two people are often needed to move and position it safely
• Replace associated seals, gaskets, and fasteners if damaged or worn
• Follow OEM disassembly/reassembly instructions and torque specs; inspect mountings and bearings during install

The Gas Burner Valve Assembly is an OEM replacement part for LG gas dryers. It is a component located beneath the gas burner that controls the flow of fuel to ignite and maintain the flame. The valve assembly receives ignition and temperature signals from the dryer's control system to precisely regulate gas levels throughout drying cycles. This gas dryer burner valve includes two solenoid coils.

Causes of a faulty gas valve may involve wear over extended operation, mineral buildup on valve seats, or mechanical issues restricting gas flow at desired levels.

Symptoms of a bad gas burner valve assembly consist of:

• Erratic or inconsistent burner ignition between cycles
• Inability to achieve high heat settings when needed
• Burners not maintaining steady flame patterns
• Potential gas leaks detected around valves or tubing

This OEM LG part is also compatible with some Sears/Kenmore dryers.

This Lifter is a replacement shelf support that helps hold and level adjustable refrigerator shelves for smooth raising and lowering. Restores secure shelf positioning so items stay stable and shelves operate correctly. What it does:

• Supports and stabilizes an adjustable refrigerator shelf, preventing sagging.
• Enables smooth lifting and lowering of the shelf when adjusting positions.
• Replaces cracked, broken, or worn plastic support that lets shelves tilt or fall.
• Helps restore proper alignment so refrigerated items sit level.

• One lifter/shelf support.

• Disconnect power to the appliance before starting any repairs.
• Remove the shelf or bin that sits on the lifter to gain access.
• Snap the lifter into the designated mounting slot; some models may require a light push or a screwdriver to assist.

This poly-V dryer drum drive belt wraps around the drum and pulleys to transfer motor power for tumbling. Replace a stretched, glazed, or broken belt to restore drum rotation and consistent drying performance.

• Transfers motor rotation to the drum for steady, even tumbling
• If broken, the motor may run but the drum won't turn
• Worn or slipping belts can cause squealing, thumping, or a burning rubber smell
• Cracks, frayed ribs, or glazing are visual signs the belt needs replacement

• Disconnect power; for gas dryers, also shut off the gas supply
• Remove top/front panels and support the drum to access the belt path
• Loop the new belt around the drum and route/tension it per the unit's belt diagram with the idler and motor pulleys
• Spin the drum by hand to check tracking before reassembly and test run

The Drum Seal is an OEM part for LG dryers. It forms an airtight seal between the rotating drum and stationary outer housing. This seal prevents air leakage that could diminish drying effectiveness.

Causes of a bad drum seal can include cracks or breaks from heat cycling over time, hardening and failure of rubber seal materials, or physical damage from cleaning tools or debris inside the drum.

Symptoms of a bad drum seal include:

• Slow or incomplete drying times
• Clothes not feeling fully dry at the end of cycles
• Excessively long heating cycles
• Noticeable air drafts around the dryer housing

This OEM LG part is also compatible with some Kenmore models.

This Pipe Assembly routes water into the appliance so the dispenser and ice maker can receive a steady supply. Replacing a damaged tube restores proper water flow and helps stop leaks or pooling inside or beneath the unit. What it does:

• Carries incoming water from the household supply to the appliance's internal water system
• Restores water delivery to the dispenser and ice maker when the original tube is cracked or blocked
• Prevents leaks and water damage caused by split, corroded, or pinched tubing
• Helps eliminate intermittent flow or weak dispenser output caused by a damaged water line

• One complete pipe assembly as shown

• Shut off the refrigerator's water supply and unplug the appliance before beginning
• Handle tubing fittings carefully; use proper tools to avoid damage or overtightening
• Inspect connection points and replace seals or clips if worn; test for leaks after reinstalling

The Dryer Ignitor is an OEM part for LG dryers. It is crucial for the ignition process in gas dryers, responsible for lighting the gas burner that provides heat for drying clothes. This ignitor must heat up to a high temperature to ignite the gas, and its proper function is essential for the dryer to operate safely and efficiently.

Symptoms of a bad Dryer Ignitor include:

• The dryer not heating up, even though all other functions are working correctly.
• The gas valve opening but no flame being produced, indicating the ignitor isn't reaching the necessary temperature.
• Intermittent heating, where the dryer sometimes produces heat and other times does not.

Causes of a bad dryer ignitor can include thermal fuse issues, a broken or malfunctioning ignitor due to wear and tear, or electrical problems affecting power delivery to the ignitor.

This OEM LG part is also compatible with Kenmore models.

For propane order 383EEL3002A.

The Liquid Propane Gas Orifice is an OEM replacement part for LG dryers. This orifice is specifically designed for models that run on liquid propane gas. It regulates the flow of gas into the burner, allowing the dryer to heat up and dry your clothes.

Causes of a faulty orifice can include corrosion from repeated heating cycles breaking down internal components. Orifices degrade naturally over extended use.

Symptoms of a failed orifice include:

• The dryer failing to properly heat or dry clothes
• Yellow flames or plumes of unburnt gas exiting the dryer vent
• Error codes related to gas or heating issues displayed

This OEM LG part is also compatible with some Kenmore models.

For natural gas order 4948EL4001B.

This duct assembly channels dryer exhaust between internal components to ensure proper airflow and help the appliance vent safely. Replacing a damaged duct restores efficient venting and can reduce drying time and heat buildup. What it does:

• Channels heated air and moisture from the drum to the external vent
• Keeps internal airflow pathways sealed to maintain drying efficiency
• Helps prevent hot spots that can cause odors or reduced performance
• Reduces air leaks that can lead to longer dry cycles or moisture buildup

• One duct assembly

• Disconnect power and, if applicable, gas supply before starting work
• Verify correct orientation and seating of seals; fasten with manufacturer-specified hardware
• Inspect adjacent hoses and clamps for wear and replace if needed

The High Limit Thermostat is an OEM part for LG dryers, designed to act as a critical safety feature within the appliance. This thermostat monitors the dryer's internal temperature, shutting off the heat source if it detects temperatures that are dangerously high. By doing so, it prevents overheating, which can lead to appliance damage or, in worst-case scenarios, fires. The high limit thermostat is a crucial component for the safe operation of your dryer, ensuring it operates within the specified temperature range.

Causes of a faulty High Limit Thermostat can include a malfunction within the thermostat itself, such as a failure to accurately detect temperature changes, or issues with the dryer that cause it to run hotter than designed, such as restricted airflow or a malfunctioning heating element.

Symptoms of a malfunctioning High Limit Thermostat include:

• The dryer not heating properly or at all
• The dryer repeatedly shutting off during cycles
• Excessive heat emanating from the dryer, indicating it is not regulating temperature correctly

This OEM LG part is also compatible with some Kenmore models.

The LAMP, LED is an OEM component specifically designed for LG dryers. It provides illumination inside the dryer drum, a crucial safety feature for easily viewing clothes during operation. Proper lighting allows users to monitor drying progress without hindering efficiency.

Causes of a bad LED lamp can include regular wear and tear over extended use, as well as potential electrical issues disrupting current flow to the lighting source.

Symptoms of a bad LED lamp include:

• Dim or completely absent lighting inside the dryer drum
• Inability to visually inspect clothes without opening the dryer door
• Premature ending of cycles due to detection of insufficient light  

The high-efficiency LED technology in this OEM part helps maximize useful life. Replace yours today to restore optimal usability. This LG replacement part is also compatible with Sears/Kenmore models.

The High Limit Thermostat is an OEM part for LG dryers, designed to act as a critical safety feature within the appliance. This thermostat monitors the dryer's internal temperature, shutting off the heat source if it detects temperatures that are dangerously high. By doing so, it prevents overheating, which can lead to appliance damage or, in worst-case scenarios, fires. The high limit thermostat is a crucial component for the safe operation of your dryer, ensuring it operates within the specified temperature range.

Causes of a faulty High Limit Thermostat can include a malfunction within the thermostat itself, such as a failure to accurately detect temperature changes, or issues with the dryer that cause it to run hotter than designed, such as restricted airflow or a malfunctioning heating element.

Symptoms of a malfunctioning High Limit Thermostat include:

• The dryer not heating properly or at all
• The dryer repeatedly shutting off during cycles
• Excessive heat emanating from the dryer, indicating it is not regulating temperature correctly

This OEM LG part is also compatible with some Kenmore models.

The Igniter Sensor is an OEM part for LG dryers. This sensor plays a critical role in the ignition process, ensuring that the gas ignites properly to produce the heat necessary for drying clothes efficiently. It helps monitor and regulate the ignition temperature.

Over time, the igniter sensor can become faulty due to regular use, exposure to high temperatures, or electrical issues. These factors can lead to a malfunction, resulting in the dryer not heating properly or failing to start.

Symptoms of a bad igniter sensor include:

• Dryer not heating up
• Long drying times
• Dryer not starting
• Unusual smells or noises during operation

This OEM LG part is also compatible with Sears/Kenmore.

A small mounting bracket that secures and supports internal appliance components to keep shelves, drawers or assemblies aligned and stable. Replaces a cracked, broken or missing supporter to restore proper fit and reduce movement. What it does

• Secures an internal component or assembly in place to prevent sagging or misalignment
• Stops rattling, wobble or looseness caused by a damaged or missing bracket
• Restores correct clearance and support for the associated shelf/drawer/assembly
• Helps maintain normal operation and prevents further wear on adjacent parts

• One supporter holder bracket

• Disconnect power before starting repairs; unplug or flip the appliance breaker
• Remove nearby shelves, drawers or panels to access the damaged bracket
• Inspect mating parts for damage and replace any worn fasteners as needed
• Use basic hand tools;

The Roller Kit is an OEM part for LG dryers. This 4 roller kit includes replacement drum support rollers, which are essential for allowing the dryer drum to rotate smoothly during operation. The rollers are designed to provide stable support for the drum, minimizing noise and ensuring efficient drying performance. 

Over time, drum rollers can wear out due to continuous use, exposure to heavy loads, or lack of proper lubrication. When the rollers become damaged or worn, they may develop flat spots, lose their smooth surface, or begin to squeak. These issues can lead to improper drum rotation or increased strain on other dryer components.

Symptoms of a bad Roller Kit include:  

• Loud squeaking, rumbling, or thumping noises during operation  
• The dryer drum not spinning or rotating unevenly  
• Excessive vibrations while the dryer is running  

This OEM LG part is also compatible with Sears/Kenmore.

This is an authentic OEM drum support roller sourced directly from the manufacturer for use in clothes dryers. During the drying cycle, the drum turns and tosses the clothes around to distribute heat. This drum support roller holds the drum in place as it rotates. Over time, the heat from the dryer can lead to the roller becoming worn. If the dryer is making squealing sounds or thumping when operating, the support roller is worn out and should be replaced. Before replacing the drum support roller, make sure the power is disconnected from the dryer. Remove the top and front panel of the dryer to reach the drum. The idler pulley and dryer belt are underneath the drum; remove these and then take the drum out of the unit and set it aside. Remove the mounting bracket holding the worn drum support roller. Remove and replace the worn roller. While the dryer is apart, inspect the remaining support rollers. Reverse the steps used and put the dryer back together. Power the dryer and make sure the drum turns.This is a black and white, rubber and metal part that is individually sold. It does not come with assembly hardware. This drum support roller is designed for dryers manufactured by LG, Kenmore, and General Electric.

The Lint Filter Assembly is an OEM part for LG dryers that captures lint and debris from your clothes during the drying cycle. This part maintains the efficiency of your dryer, allows airflow and reduce the risk of overheating. 

Causes of a bad Lint Filter Assembly can include clogging due to accumulation of lint and fabric particles, physical damage such as tears or cracks that allow lint to pass through, and wear over time.

Symptoms of a bad Lint Filter Assembly include:

• Reduced drying efficiency, leading to longer drying times
• Excessive lint and debris outside the filter area
• The dryer overheating due to restricted airflow caused by a clogged or damaged filter
• Unusual smells from trapped lint that may not be effectively captured or is getting past the filter

This OEM LG part is also compatible with some Kenmore models.

This guide cover is a small replacement trim piece that restores proper guiding and protection for the associated assembly, improving part alignment and helping keep debris out of the mechanism. What it does

• Protects and covers the guide area to prevent debris from entering the mechanism
• Helps maintain proper alignment of the adjacent moving parts
• Replaces cracked, broken or missing covers that can cause rubbing or minor noise
• Restores finished appearance to the appliance where the cover is damaged

• One guide cover

• Disconnect power before beginning any repairs; unplug the appliance or shut off the circuit
• Removal typically requires basic hand tools (screwdriver); handle panels gently to avoid breaking clips
• Secure all fasteners and retaining clips until the cover is fully seated
• Inspect adjoining parts and replace as needed

This filter guide secures and positions the refrigerator water filter for proper alignment and a reliable seal. It helps keep the filter stable during normal use so water flows correctly and filtration works as intended. What it does:

• Holds the water filter in the correct position inside the filter housing
• Helps maintain a proper seal to reduce the chance of leaks or bypassed water
• Prevents filter movement or rattling when the refrigerator door is opened
• Supports easy removal and replacement of the filter by guiding insertion

• One filter guide

• Designed to install in the refrigerator filter compartment; follow your model's service instructions
• Turn off water supply and relieve system pressure before removing or installing filter components
• Use basic hand tools as required; avoid overtightening which can damage plastic parts
• Inspect surrounding housing and O-rings for wear and replace if needed

The Pressure Sensor is an OEM replacement part for LG dryers. This sensor monitors the airflow or pressure within the dryer, helping to regulate drying cycles and ensure efficient operation. By detecting blockages or changes in airflow, it plays a critical role in maintaining proper performance and preventing overheating.

Over time, the pressure sensor can fail due to wear, electrical issues, or buildup of lint and debris. Damage to the sensor or its connections can cause the dryer to operate inefficiently or stop functioning altogether.

Symptoms of a bad pressure sensor include:

• Dryer not heating properly
• Extended drying times
• Error codes related to airflow or pressure
• Dryer shutting off unexpectedly during cycles

This OEM LG part is also compatible with Sears/Kenmore dryers.

This steam nozzle assembly directs a fine spray into the dryer drum during Steam/Refresh cycles. Replacing a clogged or cracked nozzle helps restore proper mist distribution and reduces leaks or drips from the nozzle area.

• Channels water from the inlet line into the drum for steam-enabled cycles
• Maintains the correct spray pattern and coverage
• Common symptoms: no mist/steam, weak or uneven spray, dripping, mineral buildup, or leaks around the nozzle
• Can contribute to wet spots if the spray is misdirected or blocked

• Unplug the dryer and turn off the water supply before servicing
• Allow the appliance to cool; wear gloves and eye protection
• Access is typically near the front bulkhead/drum opening; remove panels as required per model
• Ensure hose seating and clamps are secure; test for leaks after installation

The Blower Wheel is an OEM part for LG dryers. This part circulates air through the dryer drum and out the exhaust vent, ensuring proper airflow for efficient drying of clothes.

Causes of a bad blower wheel can include accumulation of lint and debris, wear and tear over time, or physical damage due to foreign objects entering the blower housing.  

Symptoms of a bad blower wheel include:

• Reduced or no airflow from the exhaust vent
• Unusual noises such as rattling or squealing during the drying cycle
• Clothes taking longer to dry or remaining damp
• Overheating or frequent shutdowns of the dryer

This OEM LG part is also compatible with some Kenmore models.

Adapt your gas dryer for propane with this LP conversion kit. It provides the correct orifice and regulator adjustments needed so the burner fires properly on LP fuel, helping ensure safe operation and consistent drying performance after a fuel change.

• Converts a compatible gas dryer from natural gas to liquid propane (LP)
• Helps ensure proper burner flame characteristics on LP
• Appropriate when moving to a home with propane or changing utilities
• Symptoms can include weak heat, improper flame, or sooting

• Disconnect power and shut off gas before servicing
• Installation and regulator/orifice adjustments must be performed per the service manual
• After installation, leak-check all connections and verify proper burner operation
• Do not attempt conversion without the correct kit for your specific model

Blower housing assembly for dryer that channels heated air from the drum to the exhaust. Replaces a cracked or damaged housing to restore proper airflow and help the dryer dry more efficiently and quietly. What it does:

• Channels heated air from the drum to the exhaust and supports the blower wheel.
• Restores airflow when a damaged or cracked housing is restricting ventilation.
• Commonly used to address reduced drying performance and longer dry times.
• Can also resolve unusual rattling or grinding noises coming from the lower front of the dryer.

• Disconnect power (and gas, if applicable) before beginning work; wear eye protection and gloves.
• Remove access panels and disconnect vent/ducting per your model's service instructions to reach the blower housing.
• Inspect the blower wheel and surrounding seals/gaskets while the housing is out; replace damaged components as needed.
• Reassemble all panels and venting securely and test the dryer for proper airflow and operation after installation.

This duct assembly routes exhaust air from the appliance to the external vent, helping maintain proper airflow and preventing leaks. It replaces a damaged or clogged duct to restore effective venting and reduce moisture buildup. What it does:

• Channels hot, moist air from the appliance to the house venting system
• Helps prevent exhaust air leaks that can reduce performance or cause odors
• Can resolve symptoms like longer dry times, damp laundry, or reduced airflow
• Reduces risk of lint buildup in damaged ducts when properly installed

• Disconnect power (and gas supply for gas models) before service to avoid shock or injury
• Use basic hand tools; support the appliance as needed for access
• Inspect adjoining seals and clamps; replace or tighten to ensure an airtight fit
• After installation, run a short test cycle and check for proper airflow and leaks

This guide assembly is a replacement slide guide that helps support and align moving components for smooth operation and reliable engagement. It restores proper tracking and reduces wobble or binding in the mechanism. What it does:

• Provides stable support and alignment for a sliding component to prevent mis-tracking and uneven movement
• Reduces noise, sticking, or binding caused by worn or damaged guides
• Helps maintain proper clearance and engagement of the moving part
• Matches OEM fit and mounting points for direct replacement

• Turn off and unplug the appliance before beginning any repair to avoid electrical shock
• Remove any obstructing panels or components to access the guide
• Inspect mating parts (slides, rails, fasteners) and replace any damaged hardware to ensure correct fit

The Dryer Thermistor is an OEM part for LG dryers, designed to monitor and help regulate the temperature within the dryer by providing feedback to the control board about the temperature inside the drum. This allows the dryer to adjust its heat settings accordingly, preventing overheating and ensuring clothes are dried evenly and safely.

Symptoms of a bad Dryer Thermistor include:

• Clothes not drying properly or taking longer than usual to dry.
• The dryer repeatedly stopping during a cycle.
• Error messages appearing on the dryer's display panel.
• The dryer getting too hot or not heating enough.

Causes of a bad Dryer Thermistor can include a buildup of lint and debris affecting its ability to accurately sense temperature, wear and tear over time, or electrical issues within the dryer's circuitry.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Dryer Blower Thermostat is an OEM replacement part for LG dryers. It plays a role in regulating the operation of the blower motor, which is responsible for circulating hot air throughout the dryer during the drying cycle.

Causes of a bad dryer blower thermostat can include electrical malfunctions, physical damage, or simply wear and tear over time.

Symptoms of a bad dryer blower thermostat include:  

• The dryer not heating up properly or taking longer to dry clothes
• The blower motor failing to turn on or running continuously
• Inconsistent or inadequate airflow during the drying cycle
• Error codes or fault indicators related to the thermostat or blower motor

This OEM LG part is also compatible with Sears/Kenmore models.

This metal mounting bracket secures internal components to the appliance frame, restoring proper alignment and reducing movement. Replace a worn or damaged bracket to stop rattling and maintain stable operation. What it does:

• Provides structural support to hold panels, controls, or assemblies in place
• Prevents excess vibration and noise caused by loose parts
• Keeps components aligned for reliable mechanical operation
• Helps maintain safe clearances between moving parts

• Turn off power and unplug the appliance before beginning work
• Use appropriate hand tools; retain any original fasteners unless replacements are specified
• Inspect adjacent parts and mounting points for damage; replace if worn

This high-quality, OEM replacement part fits LG and Kenmore dryers, ensuring efficient air circulation for optimal drying. Featuring durable construction, this blower motor addresses common issues such as inadequate drying, unusual noises, and overheating.

This clamp secures hoses, tubing or wiring to the appliance frame to help prevent rubbing, vibration and routing issues. It restores a solid attachment point so lines stay in place during normal use. What it does:

• Holds a hose, tubing or wire bundle in place to prevent chafing and abrasion
• Keeps components routed away from moving parts and hot surfaces
• Reduces rattling or vibration caused by loose lines
• Helps maintain safe, reliable connections by preventing strain on fittings

• Disconnect power and shut off water before servicing
• Use basic hand tools; avoid over-tightening which can pinch hoses or wires
• Inspect adjacent hoses/wires for wear and replace if damaged
• Take photos before removal to ensure correct reinstallation

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

The Idler Pulley Assembly is an OEM part for LG dryers. It plays a critical role in the dryer's drum belt tension system, helping to maintain proper tension on the belt so the drum can rotate smoothly during the drying cycle.

Causes of a bad idler pulley assembly can include wear and tear over time, buildup of lint or debris, or damage from an overloaded dryer. A malfunctioning idler pulley can lead to inefficient drying and potential damage to other dryer components.

Symptoms of a bad idler pulley assembly include:

• Squeaking or squealing noises during operation
• The drum not rotating properly or at all
• The dryer stopping mid-cycle
• The belt slipping or breaking

This OEM LG part is also compatible with Sears/Kenmore.

The Dryer Idler Pulley is an OEM replacement part for LG dryers. It is a critical component that helps guide and maintain proper tension on the dryer belt, ensuring efficient transfer of rotational force from the motor to the dryer drum.

Symptoms of a faulty dryer idler pulley include:

• Squeaking or grinding noises coming from the pulley area
• Visible wear, cracks, or damage to the pulley surface
• Slipping or irregular rotation of the dryer drum

Causes of a bad idler pulley can include normal wear and tear over time, exposure to high temperatures or lint buildup, misalignment or improper tracking, or physical damage from impact or foreign objects.

This OEM LG part is also compatible with Sears/Kenmore dryer models.

This replacement screw secures appliance components in their proper position. Use it to restore a tight, rattle-free fit when the original fastener is missing, stripped, or corroded. What it does:

• Fastens brackets, panels, or trim to keep assemblies aligned and secure
• Helps prevent vibration, rattling, and gaps from loose hardware
• Restores proper attachment when a screw is lost, worn, or damaged
• Common symptoms: loose panel/handle, misalignment, rattling, or a missing screw

• Disconnect power; shut off water or gas before service
• Match location to the original; start threads by hand to avoid cross-threading
• Use the correct driver bit; do not overtighten (especially into plastic)
• If the original hole is stripped, repair threads before installing the new screw

This self-tapping screw fastens panels, brackets, and internal components in compatible appliances. Replace a stripped, corroded, or missing screw to restore a secure fit and help prevent vibration, rattling, and misalignment.

• Forms/engages its own threads in sheet metal or plastic for a secure hold
• Secures covers, brackets, and assemblies to maintain alignment
• Helps reduce vibration and noise from loose components
• Replace if the head is stripped/broken, threads are worn, or the screw is missing

• Disconnect power and shut off water or gas, as applicable, before servicing
• Match to the original location and hardware; use identical length and thread where specified
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving hole is damaged, repair it before installing the new screw